JBL Sdp5 Manual

SETUPJBL Synthesis
3-22
Note:
The on-screen display appears horizontally stretched
across the display device screen when all of the fol-
lowing conditions are met:
•The S-VIDEO OSD (4:3) parameter is set to OFF.
•An anamorphic video input signal is present.
•A 16:9 display device (widescreen) is connected
to an S-video output connector.
S-VIDEO OSD 4:3ON, OFF
Controls the appearance of the on-screen display when the display
device is connected to an S-video output connector. When set to
ON, the display...

SETUPSDP-5
3-23
COMPONENT OSD ON, OFF
Controls the appearance of the on-screen display when the display
device is connected to the component video output connector.
When set to ON, the display device shows the on-screen display as
a 480i video signal on a full blue-screen background. To minimize
viewing distractions, the two-line status does not appear on the 
on-screen display. When set to OFF, the display device does not
show the on-screen display, including the two-line status (2-18).
Note:
When the...

SETUPJBL Synthesis
3-24
ZONE2 INDIGITAL, ANLG, DMIX
Controls the interaction of the digital and analog audio input connectors assigned to the selected Zone 2 input.The INPUT SETUP menu can
be used to assign one digital and one analog audio input connector for the selected input. Refer to pages 3-7 and 3-8 for more information. 
The table shown on the next page describes ZONE2 IN parameter settings.
ZONE2 IN
DVD1
INPUTS
SETUP
DVD1 INPUT SETUP
NAME DVD1
DIGITAL IN COAX-1
ANALOG IN NONE
ANLG IN LVL +0dB...

DIGITALANLG (Analog)DMIX (Downmix)
SETUPSDP-5
3-25
The SDP-5 automatically sets the
ZONE2 IN parameter to DIGITAL
when the ANALOG IN parameter
is set to NONE.
•The SDP-5 sends the
assigned digital audio input
connector to the Zone 2
audio output connectors.
The SDP-5 ignores the
assigned analog audio input
connector.
•Independent zone monitoring
is available.
•The DIGITAL IN parameter
(3-7) can be used to assign a
digital audio input connector
for the selected input.The SDP-5 automatically sets the
ZONE2...

SETUPJBL Synthesis
3-26
CUSTOM SPEAKER SETUPS
Selecting the SPEAKER SETUP menu CUSTOM SETUP option opens
the CUSTOM SETUP menu shown above, which can be used to
configure the Main Zone audio output connectors for a custom
speaker setup. The CUSTOM SETUP menu allows the selection of
independent crossover points for each Main Zone audio output
connector. Refer to the the paragraph below for more information
about determining crossover points.
Determining Crossover Points
The CUSTOM SETUP menu shown above...

SETUPSDP-5
3-27
Highpass Filter
Highpass filters attenuate low frequencies at 24dB per octave. The curves in the graph
above indicate the frequency response of each crossover setting. From left to right, the
curves represent crossover settings from 30 to 120Hz. The graph above does not
show the THX 80Hz crossover point, which is 12dB per octave.
10 20 50 100 200 500 1k dB
0
0
-12
-24
-36
-48
0
0
-60
Hz
Lowpass Filter
Lowpass filters attenuate high frequencies at 24dB per octave. The curves in the graph...

CUSTOM SETUP
FRONT L/R 40Hz
CENTER 80Hz
SIDE L/R 80Hz
REAR L/R 80Hz
SUBWOOFER 80Hz
THXULTRA2 SUB OFF
BGC N/A
ASA APART
SETUPJBL Synthesis
3-28
FRONT L/RFULL, 30Hz to 120Hz, THX 80Hz
Opens the FRONT L/R SPEAKERS menu shown above, which can be
used to select a crossover point for the Main Zone audio output
connectors labeled Front L/R. When set to FULL, the SDP-5 sends a
full-range audio output signal to these connectors. Otherwise, the
SDP-5 activates a crossover point at the selected setting. Choose
the...

CUSTOM SETUP
FRONT L/R 80Hz
CENTER 80Hz
SIDE L/R 80Hz
REAR L/R 80Hz
SUBWOOFER 80Hz
THXULTRA2 SUB OFF
BGC N/A
ASA APART
SETUPSDP-5
3-29
CENTERFULL, 30Hz to 120Hz, THX 80Hz, NONE
Opens the CENTER SPEAKER menu shown above, which can be
used to select a crossover point for the Main Zone audio output
connector labeled Center. When set to FULL, the SDP-5 sends a full-
range audio output signal to this connector. Otherwise, the SDP-5
activates a crossover point at the selected setting. Choose the
setting...

CUSTOM SETUP
FRONT L/R 80Hz
CENTER 80Hz
SIDE L/R 80Hz
REAR L/R 80Hz
SUBWOOFER 80Hz
THXULTRA2 SUB OFF
BGC N/A
ASA APART
SETUPJBL Synthesis
3-30
Note:
When the SIDE L/R parameter is set to NONE, Dolby
Digital Surround EX, THX Ultra2, THX Surround EX ,
and dts-ES decoding are not available.
SIDE L/RFULL, 30Hz to 120Hz, THX 80Hz, NONE
Opens the SIDE L/R SPEAKERS menu shown above, which can be
used to select a crossover point for the Main Zone audio output
connectors labeled Side L/R. When set to FULL, the...

CUSTOM SETUP
FRONT L/R 80Hz
CENTER 80Hz
SIDE L/R 80Hz
REAR L/R 80Hz
SUBWOOFER 80Hz
THXULTRA2 SUB OFF
BGC N/A
ASA APART
SETUPSDP-5
3-31
REAR L/RFULL, 30Hz to 120Hz, THX 80Hz, NONE
Opens the REAR L/R SPEAKERS menu shown above, which can be
used to select a crossover point for the Main Zone audio output
connectors labeled Rear L/R. When set to FULL, the SDP-5 sends a
full-range audio output signal to these connectors. Otherwise, the
SDP-5 activates a crossover point at the selected setting. Choose
the...