JBL Sdp5 Manual
Have a look at the manual JBL Sdp5 Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 57 JBL manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
SETUPJBL Synthesis 3-22 Note: The on-screen display appears horizontally stretched across the display device screen when all of the fol- lowing conditions are met: •The S-VIDEO OSD (4:3) parameter is set to OFF. •An anamorphic video input signal is present. •A 16:9 display device (widescreen) is connected to an S-video output connector. S-VIDEO OSD 4:3ON, OFF Controls the appearance of the on-screen display when the display device is connected to an S-video output connector. When set to ON, the display device shows the on-screen display in a 4:3 aspect ratio* regardless of the incoming signal. When set to OFF, the display device shows the on-screen display in the same aspect ratio as the input signal. *Aspect ratio refers to the size of the picture on the display device screen or to the size of the display device screen. A 4:3 aspect ratio is almost square. A 16:9 aspect ratio, often referred to as “widescreen,” is almost twice as wide as high. S-VIDEO OSD 4:3MAIN ADVANCEDDVD1INPUTSSETUP DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CHL7FILM %!D5.1 L7FILM DTS-ES DTS-ES L7FILM MAIN ADVANCED ZONE2 IN DIGITAL MAIN ADVANCED MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONSINPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX INPUTSDVD1 The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. DVD1 MAIN ADV INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF S-VIDEO OSD 4:3 ON ON OFF MAIN ADVANCED (continued from page 3-21)
SETUPSDP-5 3-23 COMPONENT OSD ON, OFF Controls the appearance of the on-screen display when the display device is connected to the component video output connector. When set to ON, the display device shows the on-screen display as a 480i video signal on a full blue-screen background. To minimize viewing distractions, the two-line status does not appear on the on-screen display. When set to OFF, the display device does not show the on-screen display, including the two-line status (2-18). Note: When the ON-SCREEN DISPLAY menu BACKGROUND parameter (3-51) is set to OFF, the display device using the component video output connector will not show the on-screen display. COMPONENT OSDMAIN ADVANCEDDVD1INPUTSSETUP DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CHL7FILM %!D5.1 L7FILM DTS-ES DTS-ES L7FILM MAIN ADVANCED ZONE2 IN DIGITAL MAIN ADVANCED MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONSINPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX INPUTSDVD1 The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. DVD1 MAIN ADV INPUT SELECT DIGITAL 2-CH ANLG BYP OFF S-VIDEO 16:9 AUTO S-VIDEO OSD 4:3 ON COMPONENT OSD OFF COMPONENT OSD OFF ON OFF
SETUPJBL Synthesis 3-24 ZONE2 INDIGITAL, ANLG, DMIX Controls the interaction of the digital and analog audio input connectors assigned to the selected Zone 2 input.The INPUT SETUP menu can be used to assign one digital and one analog audio input connector for the selected input. Refer to pages 3-7 and 3-8 for more information. The table shown on the next page describes ZONE2 IN parameter settings. ZONE2 INDVD1INPUTSSETUP DVD1 INPUT SETUP NAME DVD1 DIGITAL IN COAX-1 ANALOG IN NONE ANLG IN LVL +0dB VIDEO IN S-VIDEO-1 COMPONENT IN 1 2-CHL7FILM %!D5.1 L7FILM DTS-ES DTS-ES L7FILM MAIN ADVANCED ZONE2 IN DIGITAL ZONE2 IN DIGITAL MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONSINPUT SETUP DVD1 DVD2 SAT VCR TV CD TUNER AUX INPUTSDVD1 The DVD1 INPUT SETUP menu is shown here as an example, and will continue to be shown as an example throughout this section. Whenever it appears, any other INPUT SETUP menu may be substituted. Likewise, whenever the DVD1 input appears as a step in a menu path, any other input may be substituted. DIGITAL ANLG DMIX When the ZONE2 IN parameter is set to DIGITAL or ANLG, the SDP-5 recognizes some dts-encoded input sources as audio signals (not data signals) and outputs loud digital noise from the Zone 2 audio output connectors.CAUTION
DIGITALANLG (Analog)DMIX (Downmix) SETUPSDP-5 3-25 The SDP-5 automatically sets the ZONE2 IN parameter to DIGITAL when the ANALOG IN parameter is set to NONE. •The SDP-5 sends the assigned digital audio input connector to the Zone 2 audio output connectors. The SDP-5 ignores the assigned analog audio input connector. •Independent zone monitoring is available. •The DIGITAL IN parameter (3-7) can be used to assign a digital audio input connector for the selected input.The SDP-5 automatically sets the ZONE2 IN parameter to ANLG when the DIGITAL IN parameter is set to NONE. •The SDP-5 sends the assigned analog audio input connector to the Zone 2 audio output connectors. The SDP-5 ignores the assigned digital audio input connector. •Independent zone monitoring is available. •The ANALOG IN parameter (3-8) can be used to assign an analog audio input connector for the selected input.Set the ZONE2 IN parameter to DMIX to send a downmixed version of Main Zone audio to the Zone 2 audio output connectors. Downmixes can be generated for Dolby Digital and dts(-ES) sources. •To generate a downmix, the same input must be selected in the Main Zone and Zone 2. Otherwise, the Zone 2 audio output connectors will mute. •Main Zone listening mode activation affects the Zone 2 audio output connectors. For instance, when the MONO listening mode is activated in the Main Zone, the Zone 2 audio output connectors will generate mono output signals. •Downmixes cannot be generated when the 5.1a BYPASS listening mode is activated in the Main Zone. However, when the ZONE2 IN parameter is set to DMIX, the signals from the Main Zone audio output connectors labeled Front L/R are sent to Zone 2. Signals from other Main Zone audio output connectors are ignored. •Independent zone monitoring is NOTavailable. •It is recommended to set the ZONE2 IN parameter to DMIX when recording from a DVD player without built-in Dolby Digital or dts-ES decoding to a VCR or PVR (i.e. Tivo ®or Replay TV®). •The SDP-5 automatically uses LOGIC7 encoding to downmix multi-channel input sources (except 5.1-channel analog sources) to LOGIC7-encoded stereo output signals for listening and recording. LOGIC7-encoded downmixes are compatible with matrix decoders, but will sound best when played back through a LOGIC7 listening mode. ZONE2 IN Parameter Settings The table below describes ZONE2 IN parameter settings.
SETUPJBL Synthesis 3-26 CUSTOM SPEAKER SETUPS Selecting the SPEAKER SETUP menu CUSTOM SETUP option opens the CUSTOM SETUP menu shown above, which can be used to configure the Main Zone audio output connectors for a custom speaker setup. The CUSTOM SETUP menu allows the selection of independent crossover points for each Main Zone audio output connector. Refer to the the paragraph below for more information about determining crossover points. Determining Crossover Points The CUSTOM SETUP menu shown above can be used to assign independent crossover points for each Main Zone audio output connector. Crossover points can be selected in 10Hz increments CUSTOM SETUPSPEAKERSSETUP SPEAKER SETUP Selecting the SETUP menu SPEAKERS option opens the SPEAKER SETUP menu shown below, which can be used to configure the Main Zone audio output connectors for the desired speaker setup, set speaker distances, and calibrate output levels. The SDP-5 has eight Main Zone audio output connectors labeled Front L/R, Center, Subwoofer, Side L/R, and Rear L/R. SPEAKER SETUPSPEAKERSSETUP within a 30 to 120Hz range. With the exception of THX 80Hz, all crossover points activate a 24dB-per-octave filter. The graphs on the next page indicate the frequency response of these crossover points. The THX 80Hz crossover point activates a 12dB-per-octave filter for the Main Zone audio output connectors labeled Front L/R, Center, Side L/R, and Rear L/R, and a 24dB-per-octave filter for the Main Zone audio output connector labeled Subwoofer. For each Main Zone audio output connector, select the crossover point closest to the low-frequency rating of the associated speaker. For the output connector labeled Subwoofer, select the crossover point equal to the lowest crossover point of the other speakers. MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKERS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION 80Hz80Hz 80Hz80Hz80Hz 80Hz80Hz 80Hz L M SUB R C SL SR RL RR CUSTOM SETUP CUSTOM SETUP FRONT L/R 80Hz CENTER 80Hz SIDE L/R 80Hz REAR L/R 80Hz SUBWOOFER 80Hz THXULTRA2 SUB OFF BGC N/A ASA APART
SETUPSDP-5 3-27 Highpass Filter Highpass filters attenuate low frequencies at 24dB per octave. The curves in the graph above indicate the frequency response of each crossover setting. From left to right, the curves represent crossover settings from 30 to 120Hz. The graph above does not show the THX 80Hz crossover point, which is 12dB per octave. 10 20 50 100 200 500 1k dB 0 0 -12 -24 -36 -48 0 0 -60 Hz Lowpass Filter Lowpass filters attenuate high frequencies at 24dB per octave. The curves in the graph above indicate the frequency response of each crossover setting. From left to right, the curves represent crossover settings from 30 to 120Hz. In general, low frequencies will be redirected from speakers with the highest crossover points to speakers with the lowest crossover points. Low-frequency signals lower than the lowest crossover point will be redirected to the subwoofer. If the lowest crossover point is FULL, low- frequency signals, excluding LFE information, will not be redirected to the subwoofer. . . . Custom Speaker Setups continues on page 3-28
CUSTOM SETUP FRONT L/R 40Hz CENTER 80Hz SIDE L/R 80Hz REAR L/R 80Hz SUBWOOFER 80Hz THXULTRA2 SUB OFF BGC N/A ASA APART SETUPJBL Synthesis 3-28 FRONT L/RFULL, 30Hz to 120Hz, THX 80Hz Opens the FRONT L/R SPEAKERS menu shown above, which can be used to select a crossover point for the Main Zone audio output connectors labeled Front L/R. When set to FULL, the SDP-5 sends a full-range audio output signal to these connectors. Otherwise, the SDP-5 activates a crossover point at the selected setting. Choose the setting closest to the low-frequency rating of the associated speakers. FRONT L/RCUSTOM SETUPSPEAKERSSETUP Default Possible Parameter Setting Settings FRONT L/R 80Hz FULL, 30 to 120Hz, THX 80Hz CENTER 80Hz FULL, 30 to 120Hz, THX 80Hz, NONE SIDE L/R 80Hz FULL, 30 to 120Hz, THX 80Hz, NONE REAR L/R 80Hz FULL, 30 to 120Hz, THX 80Hz, NONE SUBWOOFER 80Hz FULL, 30 to 120Hz, THX 80Hz, NONE THX ULTRA2 SUB OFF ON, OFF BGC N/A ON, OFF ASA APART TOGETHER, CLOSE, APART MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKERS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION 80Hz80Hz 80Hz80Hz80Hz 80Hz80Hz 80Hz L M SUB R C SL SR RL RR CUSTOM SETUPFRONT L/R 80HzFRONT L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz Custom Speaker Setups(continued from page 3-27)
CUSTOM SETUP FRONT L/R 80Hz CENTER 80Hz SIDE L/R 80Hz REAR L/R 80Hz SUBWOOFER 80Hz THXULTRA2 SUB OFF BGC N/A ASA APART SETUPSDP-5 3-29 CENTERFULL, 30Hz to 120Hz, THX 80Hz, NONE Opens the CENTER SPEAKER menu shown above, which can be used to select a crossover point for the Main Zone audio output connector labeled Center. When set to FULL, the SDP-5 sends a full- range audio output signal to this connector. Otherwise, the SDP-5 activates a crossover point at the selected setting. Choose the setting closest to the low-frequency rating of the associated speaker. When set to NONE, the SDP-5 redirects center channel signals to the Main Zone audio output connectors labeled Front L/R. CENTERCUSTOM SETUPSPEAKERSSETUP Note: When the CENTER parameter is set to NONE, center channel signals will not be redirected if the 5.1a BYPASS listening mode is activated. To redirect center channel signals, configure the speaker setup with the associated DVD-A/SACD player. . . . Custom Speaker Setups continues on page 3-30 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKERS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION 80Hz80Hz 80Hz80Hz80Hz 80Hz80Hz 80Hz L M SUB R C SL SR RL RR CUSTOM SETUPCENTER 80Hz CENTER SPEAKER FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz NONE
CUSTOM SETUP FRONT L/R 80Hz CENTER 80Hz SIDE L/R 80Hz REAR L/R 80Hz SUBWOOFER 80Hz THXULTRA2 SUB OFF BGC N/A ASA APART SETUPJBL Synthesis 3-30 Note: When the SIDE L/R parameter is set to NONE, Dolby Digital Surround EX, THX Ultra2, THX Surround EX , and dts-ES decoding are not available. SIDE L/RFULL, 30Hz to 120Hz, THX 80Hz, NONE Opens the SIDE L/R SPEAKERS menu shown above, which can be used to select a crossover point for the Main Zone audio output connectors labeled Side L/R. When set to FULL, the SDP-5 sends a full-range audio output signal to these connectors. Otherwise, the SDP-5 activates a crossover point at the selected setting. Choose the setting closest to the low-frequency rating of the associated speakers. When set to NONE, the SDP-5 redirects side channel signals to the Main Zone audio output connectors labeled Rear L/R. If the CUSTOM SETUP menu REAR L/R parameter is also set to NONE, the SDP-5 redirects surround channel signals to the Main Zone audio output connectors labeled Front L/R. SIDE L/RCUSTOM SETUPSPEAKERSSETUP Custom Speaker Setups(continued from page 3-29) MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKERS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION 80Hz80Hz 80Hz80Hz80Hz 80Hz80Hz 80Hz L M SUB R C SL SR RL RR CUSTOM SETUP SIDE L/R 80Hz SIDE L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz NONE
CUSTOM SETUP FRONT L/R 80Hz CENTER 80Hz SIDE L/R 80Hz REAR L/R 80Hz SUBWOOFER 80Hz THXULTRA2 SUB OFF BGC N/A ASA APART SETUPSDP-5 3-31 REAR L/RFULL, 30Hz to 120Hz, THX 80Hz, NONE Opens the REAR L/R SPEAKERS menu shown above, which can be used to select a crossover point for the Main Zone audio output connectors labeled Rear L/R. When set to FULL, the SDP-5 sends a full-range audio output signal to these connectors. Otherwise, the SDP-5 activates a crossover point at the selected setting. Choose the setting closest to the low-frequency rating of the associated speakers. When set to NONE, the SDP-5 redirects rear channel signals to the Main Zone audio output connectors labeled Side L/R. If the CUSTOM SETUP menu SIDE L/R parameter is also set to NONE, the SDP-5 redirects surround channel signals to the Main Zone audio output connectors labeled Front L/R. REAR L/RCUSTOM SETUPSPEAKERSSETUP Note: When the REAR L/R parameter is set to NONE: •Dolby Digital Surround EX, THX Ultra2, THX Surround EX, and dts-ES decoding are not available. •The ASA parameter is not available. . . . Custom Speaker Setups continues on page 3-32 MAIN MENU MODE ADJUST AUDIO CONTROLS SETUP SETUP SETUP INPUTS SPEAKERS REAR PANEL CONFIG DISPLAYS VOLUME CONTROLS TRIGGER LOCK OPTIONS SPEAKERS SPEAKER SETUP CUSTOM SETUP SYNTHESIS 7CH SETUP SPEAKER DISTANCES LEVELS CALIBRATION 80Hz80Hz 80Hz80Hz80Hz 80Hz80Hz 80Hz L M SUB R C SL SR RL RR CUSTOM SETUP REAR L/R 80Hz REAR L/R SPEAKERS FULL 30Hz 40Hz 50Hz 60Hz 70Hz 80Hz THX 80Hz 90Hz 100Hz 110Hz 120Hz NONE