InFocus Projector IN5316HDa User Manual

— 34 — 
Settings 2 Menu  
Press the  MENU button to open the  OSD menu. Press  ◄► to move to the  Settings 2 menu. Press 
▲▼  to move up and down in the  Settings 2 menu.  
 
ITEM DESCRIPTION 
Auto Source  Press  ◄► to enter and enable or disable  automatic source detection.  
No Signal Power 
Off (min.) Press 
◄► to enter and enable or disable automat ic shutdown of the lamp when no 
signal is detected. 
Auto Power On  Press 
◄► to enter and enable or disable automatic power On when AC power is...

  – 35 – 
Status 
Press ▲▼ to move up and down in the Settings 2 menu. Select the Status menu and press Enter 
or ► to enter. 
 
ITEM DESCRIPTION 
Active Source Displays the active source. 
Video Information Displays resolution/video information for RGB source and color standard for Video 
source. 
Lamp Hours Lamp hour used information is displayed (ECO, Normal, Boost). 
Software Version Displays the system software version. 
Serial Number Displays the serial number of this projector. 
  

— 36 — 
Advanced 1 Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press 
▲▼ to move to the Advanced 1 menu and then press Enter or ►. Press ▲▼ to move up and down 
in the Advanced 1 menu. Press ◄► to enter and change values for setting. 
 
ITEM DESCRIPTION 
Menu Position Press ◄► to enter and select different OSD location. 
Translucent Menu Press ◄► to enter and select OSD background translucent level.  
Low Power Mode 
Press ◄► to enter and select Low Power...

  – 37 – 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp Timer on page 44 to reset the lamp hour counter. 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
DHCP 
Press ◄► to turn DHCP On or Off.  
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, 
and DNS fields. 
IP Address  Enter a valid IP address if DHCP is turned off. 
Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is...

— 38 — 
Controlling the projector remotely 
 
 
To control your projector remotely, use one of the supported external devices listed below, or use 
RS232 using a TelNet utility, such as HyperTerminal. 
 Crestron is a registered trademark of Crestron Electronics, Inc. of the United States. 
 Extron is a registered trademark of Extron Electronics, Inc. of the United States. 
 AMX is a registered trademark of AMX LLC of the United States. 
 PJLink applied for trademark and logo registration in Japan,...

  – 39 – 
Advanced 2 Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Settings 2 menu. Press 
▲▼ to move to the Advanced 2 menu and then press Enter or ►. Press ▲▼ to move up and down 
in the Advanced 2 menu. Press ◄► to enter and change values for setting. 
 
ITEM DESCRIPTION 
Sleep Timer (min) Press ◄► to enter and set Sleep timer. The projector automatically turns off after the 
preset period of time. 
Source Filter Press  (Enter) / ► to enter the Source Filter menu. See...

— 40 — 
Source Filter 
Press the ENTER button to enter the Source Filter sub menu. 
 
ITEM DESCRIPTION 
DVI Press ◄► to enter and enable or disable the DVI source. 
HDMI Press ◄► to enter and enable or disable the HDMI source. 
DisplayPort Press ◄► to enter and enable or disable the Displaymort source. 
VGA1 Press ◄► to enter and enable or disable the VGA1 source. 
VGA2 Press ◄► to enter and enable or disable the VGA2 source. 
BNC Press ◄► to enter and enable or disable the BNC source. 
Component Video...

  – 41 – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. Be sure to use the InFocus lamp module 
designed for this projector. You can order new lamps from www.infocusstore.com (in select areas), your 
retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. Use of non 
InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not 
liable for the performance, safety...

— 42 — 
4.  Loosen the captive screw 
on the lamp cover. 
 
5.  Pull up and remove the 
cover. 
6.  Use a screwdriver to 
loosen the two captive 
screws from the lamp 
module. 
 
7.  Pull out the lamp module. 
     

  – 43 – 
8.  Reverse steps 1 to 7 to 
install the new lamp 
module.  
While installing, align the 
lamp module with the 
connector and ensure it is 
level to avoid damage. 
Note:  
The lamp module must sit 
securely in place and the 
lamp connector must be 
connected properly before 
tightening the screws.