InFocus Projector IN5316HDa User Manual

— 
i  —   Copyright 
This  publication,  including  all  photographs,  illustrations  and  software,  is  protected  under  international 
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may 
be reproduced without written consent of the author. 
©  Copyright 2014 
Disclaimer  The  information  in  this  document  is  subject  to  change  without  notice.  The  manufacturer  makes  no 
representations  or  warranties  with  respect  to  the...

— ii — 
Important Safety Information 
 Important: 
It is strongly recommended that you read this section carefully before using the projector. These 
safety and usage instructions will ensure that you enjoy many years of safe use of the projector. 
Keep this manual for future reference. 
Symbols Used 
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.  
The following styles are used in this manual to alert you to important information. 
Note: 
Provides...

– iii – 
Projector Installation Notice 
 Place the projector in a horizontal position 
The tilt angle of the projector should not exceed 15 degrees. In addition, the projector should 
not be installed in any other way except desktop and ceiling mount positions. Otherwise lamp life 
could decrease dramatically, and may lead to other unpredictable damage. 
     
 Allow at least 50 cm (19.69 inch) clearance around the exhaust vent. 
   
   
 
 Ensure that the intake vents do not recycle hot air from the...

— iv — 
Power Safety 
 Only use the supplied power cord. 
 Do not place anything on the power cord. Place the power cord where it will not be in the way of 
foot traffic. 
 Remove the batteries from the remote control when storing or not in use for a prolonged period. 
Replacing the Lamp 
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 41 
for clear and safe instructions for this procedure. Before replacing the lamp: 
 Unplug the power cord. 
 Allow...

–
v – Table of Contents 
GETTING STARTED  ........................................................................\
................................................................................... 1P
ACKING  CHECKLIST  ........................................................................\
................................................................................... 1 V
IEWS OF  PROJECTOR  PARTS  ........................................................................\...

— 
vi  —   SPECIFICATIONS
 ........................................................................\
.....................................................................................  51S
PECIFICATIONS  ........................................................................\
.........................................................................................  51P
ROJECTION D ISTANCE VS. P ROJECTION S IZE  (1080P)...

–1 –
GETTING STARTED 
Packing Checklist 
Carefully unpack the projector and check that the following items are included:  
DLP
 PROJECTOR  
REMOTE CONTROL  
(BATTERIES NOT INCLUDED)  CD-ROM
 
(THIS USER’S MANUAL)  QSC 
VGA
 CABLEPOWER CORD
(VARIES PER COUNTRY)  S
AFETY & WARRANTY 
BOOKLET 
Contact your dealer immediately if any items are mi
ssing, appear damaged, or if the unit does not work. It 
is recommend that you keep the original packing ma terial should you ever need to return the equipment 
for...

— 
2  —   Views of Projector Parts 
Front-angled View 
I TEM   L ABEL   D ESCRIPTION   S EE PAGE :  
1.   IR receiver   Receive s   the  IR signals from the remot e control .  
7  
2.   Lens   Projection Lens .  
3.   Focus ring   Focuses the projected image .  
17  
4.   Zoom ring   Enlarges the projected image .  
5.   Elevator foot   Adjusts level of projector .  
14  
6.   Function keys   See Top view — On - screen Display (OSD) 
but tons .   3  
7.   Lamp cover   Remo ve   cover to replace lamp ....

–
3 – Top view
—On-screen Display (OSD) buttons  I TEM   L ABEL   D ESCRIPTION   S EE PAGE :  
1.   M ENU   Open and exit OSD menus .  
20  2.   ◄   (Left cursor)  Navigate and change settings in the OSD .  
Quick Menu  –   For Volume  
3.   ▲ (Up cursor)  Navigate the OSD .  
Quick Menu  –   For Keystone .  
4.   ▼ (Down cursor)  Navigate the OSD .  
Quick Menu  –   For Keystone .  
5.   ► (Right cursor) Navigate and change setti ngs in the OSD .  
Quick Menu  –   For Volume .  
6.   SELECT   Enter or...