InFocus Projector IN5132 User Manual

							87
SECURITY menu
This projector is equipped with security functions.
From the SECURITY menu, you can perform the items shown in the table below.To use the SECURITY menu: User registration is required before using the security functions.
Enter to the SECURITY menu
1.  Press the ► button. The ENTER PASSWORD box will be displayed.  
2.  Use the ▲/▼/◄/► buttons to enter the password. The factory default password is as follows.    IN5132, IN5142: 6007 
     IN5134, IN5134a, IN5144, IN5144a: 4407      IN5135, IN5145: 6107 This password can be changed (below). Move the cursor to the right side of the ENTER PASSWORD box and press the ► button to display the SECURITY menu.
• We strongly recommend changing the factory default password as soon as possible.• If an incorrect password is entered, the ENTER PASSWORD box will be displayed again. If an incorrect password is entered 3 times, the projector will turn off. Afterwards the projector will turn off every time an incorrect password is entered.3.  Items shown in the table below can be performed.
If you have forgotten your password(1)   While the ENTER PASSWORD box is displayed, press and hold the RESET button on the remote control for about 3 seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector.
(2)  
A 10 digit Inquiring Code will be displayed. Contact your dealer with the 10 digit Inquiring Code. Your password will be sent to you after your user registration has been verified.
• If the Inquiring Code is displayed and no one operates the keys for approximately 55 seconds, the menu will close. If necessary, repeat the process starting from item (1).  
ItemDescription
SECURITY PASSWORD CHANGE
(1)   
Use the ▲/▼ buttons on the SECURITY menu to select SECURITY PASSWORD CHANGE and press the ► button to display the ENTER NEW PASSWORD box.(2)  Use the ▲/▼/◄/► buttons to enter the new password.(3)  
Move the cursor to the right side of the ENTER NEW PASSWORD box and press the ► button to display the NEW PASSWORD AGAIN box. Enter the same password again. (4)  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button and the NOTE NEW PASSWORD box will be displayed for about 30 seconds. Write down the password at this time.Pressing the ENTER button on the remote control or ► button on the projector will close the NOTE NEW PASSWORD box.
• Do not forget your password.
(continued on next page)
SECURITY menu 
						

							88
SECURITY menu
ItemDescription
MyScreen 
PASSWORD
The MyScreen PASSWORD function can be used to prohibit access to the MyScreen function and prevent the current MyScreen image from being overwritten.
1 Turning on the MyScreen PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to select MyScreen PASSWORD and press the ► button to display the MyScreen PASSWORD on/off menu.1-2  Use the ▲/▼ buttons on the MyScreen PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.1-3  Use the ▲/▼/◄/► buttons to enter the password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box. Enter the same PASSWORD again.1-4  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press the ► button to display the NOTE NEW PASSWORD box. This will display for about 30 seconds. Write down the password at this time. Press the ENTER button on the remote control or ► button on the projector to return to the MyScreen PASSWORD on/off menu.
When a password is set for MyScreen:
• The MyScreen registration function (and menu) will be unavailable.
• The MyScreen Lock menu will be unavailable.
• The START UP setting will be locked on MyScreen (and the menu will be unavailable).Turning the MyScreen PASSWORD off will allow normal operation of these functions.
• Do not forget your MyScreen PASSWORD.
2 Turning off the MyScreen PASSWORD2-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off menu.2-2  
Select OFF to display the ENTER PASSWORD box (large). Enter the password and the screen will return to the MyScreen PASSWORD on/off menu.
If an incorrect PASSWORD is entered, the menu will close. If necessary, repeat the process starting from item 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MyScreen PASSWORD on/off menu.3-2  Select OFF to display the ENTER PASSWORD box (large). A 10 digit Inquiring Code will be displayed inside the box.
3-3  Contact your dealer with the 10 digit Inquiring Code. Your password will be sent to you after your user registration has been verified.
(continued on next page)
ENTER NEW PASSWORD box (small)
ENTER PASSWORD box (large) 
						

							89
SECURITY menu
ItemDescription
PIN LOCK
PIN LOCK is a function which prevents the projector from being used unless a registered Code is entered.
1 Turning on the PIN LOCK1-1  Use the ▲/▼ buttons on the SECURITY menu to select PIN LOCK and press the ► button or the ENTER button to display the PIN LOCK on/off menu.1-2  Use the ▲/▼ buttons on the PIN LOCK on/off menu to select ON and the Enter PIN Code box will be displayed. 1-3  Input a 4 digit PIN code using the ▲/▼/◄/►, COMPUTER 1 and INPUT buttons. The PIN Code again box will appear.  Reenter the same PIN code. This  will complete the PIN code registration.
• If the Enter PIN Code box or the PIN Code  Again box is displayed and no one operates the keys for approximately 55 seconds, the menu will close. If necessary, repeat the process starting from item 1-1.
Afterwards, the Enter PIN Code box will display each time AC power has been turned off and the projector is restarted. Enter the registered PIN code.The projector can be used after the correct PIN code has been entered. If an incorrect PIN code is entered, the Enter PIN code box will be displayed again.If an incorrect PIN code is entered 3 times, the projector will turn of f. Afterwards the projector will turn off every time an incorrect PIN code is entered. If the Enter PIN code box is displayed and no one operates the keys for approximately 5 minutes, the projector will turn off.This function is activated when AC power to the projector has been turned off and the projector is restarted.
• Do not forget your PIN code.
2 Turning off the PIN LOCK2-1  Follow the procedure in 1-1 to display the PIN LOCK on/off menu. 2-2  Use the ▲/▼ buttons to select OFF and the Enter PIN Code box will be displayed. Enter the registered PIN code to turn the PIN LOCK function off.
If an incorrect PIN code is entered 3 times, the projector will turn of f. 
3 If you have forgotten your PIN code3-1  While the Enter PIN code box is displayed, press and hold the RESET button for three seconds or press and hold the INPUT button for 3 seconds while pressing the ► button on the projector. A 10 digit Inquiring Code will be displayed.
• If the Inquiring Code is displayed and no one operates the keys for approximately 5 minutes, the projector will turn off.3-2  Contact your dealer with the 10 digit Inquiring Code. Your PIN code will be sent to you after your user registration has been verified.
(continued on next page) 
						

							90
SECURITY menu
ItemDescription
TRANSITION DETECTOR
If this function is ON and the projector's vertical angle or INSTALLATION setting is different from the previous recorded setting, the TRANSITION DETECTOR ON alarm will be displayed instead of an input signal.
• To display the input signal again, turn this function OFF.• The projector will display the TRANSITION DETECTOR ON alarm for approximately 5 minutes and then the lamp will turn off.• The keystone adjustment feature is not available while the Transition Detector function is on.
1 Turning on the TRANSITION DETECTOR1-1  Use the ▲/▼ buttons on the SECURITY menu to select TRANSITION DETECTOR and press the ► or ENTER button to display the TRANSITION DETECTOR on/off menu.1-2  Use the ▲/▼ buttons on the TRANSITION DETECTOR on/off menu to select ON. Selecting ON will save the setting of the current angle and the INSTALLATION setting. The ENTER NEW PASSWORD box (small) will be displayed.1-3  Use the ▲/▼/◄/► buttons to enter a password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box. Enter the same password again.1-4  Move the cursor to the right side of the  NEW PASSWORD AGAIN box and press  the ► button to display the NOTE NEW  PASSWORD box. It will display for about  30 seconds. Write the password down at this  time.Press the ENTER button on the remote control or the ► button on the projector to return to the TRANSITION DETECTOR on/off menu.
• Do not forget your TRANSITION DETECTOR password.• This function will only activate when AC power has been turned off and the projector has been restarted.• If this feature has been turned ON and the projector is on an unstable surface, this feature may not function properly.
2 Turning off the TRANSITION DETECTOR2-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.2-2  Select OFF to display the ENTER PASSWORD box (large). Enter the password and the screen will return to the TRANSITION DETECTOR on/off menu.
If an incorrect password is entered, the menu will close. If necessary, repeat the process starting from item 2-1.
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the TRANSITION DETECTOR on/off menu.3-2  Select OFF to display the ENTER PASSWORD box (large). A 10 digit Inquiring Code will be displayed inside the box.3-3  Contact your dealer with the 10 digit Inquiring Code. Your password will be sent to you after your user registration has been verified.
ENTER NEW PASSWORD box (small)
ENTER PASSWORD box (large) 
						

							91
SECURITY menu
ItemDescription
MY TEXT PASSWORD
The MY TEXT PASSWORD function can prevent the MY TEXT from being overwritten. When the password is set for the MY TEXT;• The MY TEXT DISPLAY menu will be unavailable, which can prohibit changing the DISPLAY setting.• The MY TEXT WRITING menu will be unavailable, which can prevent the MY TEXT from being overwritten.
1 Turning on the MY TEXT PASSWORD1-1  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT PASSWORD and press the ► button to display the MY TEXT PASSWORD on/off menu.1-2  Use the ▲/▼ buttons on the MY TEXT PASSWORD on/off menu to select ON. The ENTER NEW PASSWORD box (small) will be displayed.1-3  Use the ▲/▼/◄/► buttons to enter the password. Move the cursor to the right side of the ENTER NEW PASSWORD box (small) and press the ► button to display the NEW PASSWORD AGAIN box, and then enter the same password again.1-4  Move the cursor to the right side of the NEW PASSWORD AGAIN box and press ► button to display the NOTE NEW PASSWORD box for about 30 seconds. Write the password down at this time.
Press the ENTER button on the remote control or ► button on the projector to return to the MY TEXT PASSWORD on/off menu. 
2 Turning off the MY TEXT PASSWORD2-1  Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off menu.2-2  Select OFF to display the ENTER PASSWORD box (large). Enter the password and the screen will return to the MY TEXT PASSWORD on/off menu. 
If an incorrect password is entered, the menu will close. If necessary, repeat the process starting  from item 2-1
3 If you have forgotten your password3-1  Follow the procedure in 1-1 to display the MY TEXT PASSWORD on/off menu.3-2  Select OFF to display the ENTER PASSWORD box (large). A 10 digit inquiring code will be displayed inside the box. 3-3  Contact your dealer with the 10 digit inquiring code. Your password will be sent to you after your user registration has been verified.
(continued on next page)
ENTER NEW PASSWORD  box (small)
ENTER PASSWORD box (large) 
						

							92
SECURITY menu
ItemDescription
MY TEXT DISPLAY
(1)  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT DISPLAY and press the ► or ENTER button to display the MY TEXT DISPLAY on/off menu.
(2)  Use the ▲/▼ buttons on the MY TEXT DISPLAY on/off menu to select on or off.
ON ó OFF
When this is set to ON, the START UP screen will display MY TEXT and when INFORMATION on the SERVICE menu is selected, INPUT_INFORMATION will display.
• This function is only available when the MY TEXT PASSWORD function is set to OFF.
MY TEXT WRITING
(1)  Use the ▲/▼ buttons on the SECURITY menu to select the MY TEXT WRITING and press the ► button. The MY TEXT WRITING dialog will display.
(2)  
The current MY TEXT will be displayed on the first 3 lines. If nothing has been entered yet, the lines will be blank.  Use the ▲/▼/◄/► buttons and the ENTER or INPUT button to select and enter characters. To erase 1 character at one time, press the RESET button or press the ◄ and INPUT button simultaneously. Also if you highlight DELETE or ALL CLEAR on screen and press the ENTER or INPUT button, you can erase one character or all characters at a time. Up to 24 characters can be entered on each MY TEXT line.
(3)  
To change an existing character, press the ▲/▼ button to move the cursor to one of the first 3 lines, and use the ◄/► buttons to highlight the character to be changed.After pressing the ENTER or INPUT button, the character is selected. Then, repeat item (2) above.
(4)  
To finish entering text, move the cursor to OK and press the ►, ENTER or INPUT button. To revert to the previous MY TEXT without saving changes, move the cursor to CANCEL and press the ◄, ENTER or INPUT button.
• The MY TEXT WRITING function is only available when the MY TEXT PASSWORD function is OFF.
(continued on next page) 
						

							93
SECURITY menu
ItemDescription
SECURITY INDICATOR
Select this to display the SECURITY INDICATOR dialog. Use the ▲/▼ buttons to select ON or OFF.
ON ó OFF
When PIN LOCK or TRANSITION DETECTOR is ON and this is turned ON, the SECURITY indicator blinks yellow in the standby mode (89, 90).
STACK LOCKSelect this to display the STACK LOCK dialog. For more information, see the Instant Stack Guide. 
						

							94
Presentation tools
Presentation tools
PC-LESS Presentation reads image and audio data from a storage media device 
inserted into the USB TYPE A ports and displays images in the following modes.
PC-LESS Presentation can be started by selecting the USB TYPE A as the input 
source.
This feature allows you to make your presentations without your computer.
PC-LESS Presentation
- Thumbnail mode (95)
- Full Screen mode (99)
- Slideshow mode (101)
[Supported storage media]
• USB memory (USB memory type, USB hard disk and USB card reader type)
• Some USB memory devices and/or USB hubs may not operate properly.
• USB devices with security software may not work.
• Be careful when inserting or removing a USB device. (12, 97)
NOTE
• NTFS is not supported.NOTE
[Supported format]
• FAT12, FAT16 and FAT32
The projector has the following convenient tools that enable on-screen 
presentations easily and quickly:
- PC-LESS Presentation (below)
- USB Display (104)
-  Network Presentation 
For more details about Network Presentation, refer to the Network Guide and 
the LiveViewer manual.
[Supported file format and its extension]
• JPEG (.jpeg, .jpg)  * Progressive is not supported.
• Bitmap (.bmp) *  16bit mode and compressed bitmap is not supported.
• PNG (.png) * Interlace PNG is not supported.
• GIF (.gif) 
• Movie (.avi, .mov) *  Supported video format: Motion-JPEG 
Supported audio format:  WAV (Linear PCM, Stereo 
16bit), IMA-ADPCM
(continued on next page) 
						

							95
Presentation tools
• Files with a resolution larger than the following are not supported. 
   IN5132, IN5142: 1024 x 768 (Still), 768 x 576 (Movie)
   IN5134, IN5134a, IN5144, IN5144a: 1280 x 800 (Still), 768 x 576 (Movie)
   IN5135, IN5145: 1920 x 1200 (Still), 768 x 576 (Movie)
(* Some computers may not support these resolutions.)
• Files with a resolution smaller than 36 x 36 are not supported.
• Files with a resolution smaller than 100 x 100 may not be displayed.
• Movie images with a frame rate higher than 15 fps cannot be displayed.
• Movie images with a bit rate higher than 20 Mbps cannot be displayed.
• Some supported files may not be displayed.
• Only a frame appears when the image data content cannot be displayed in 
the Thumbnail mode.
• Even with the file format and audio format combinations described above, 
playback of some files may fail.
NOTE
Thumbnail Mode
PC-LESS Presentation (continued)
The Thumbnail mode displays the images saved in a USB storage device on the 
Thumbnail screen. A maximum of 20 images can be displayed on a screen.
After you select some images in the Thumbnail mode, you can jump into Full 
Screen mode or Slideshow mode if desired.
Thumbnail mode will start automatically when the USB TYPE A source is 
selected.
Thumbnail menu
Selected image
Thumbnail images 
						

							96
Presentation tools
PC-LESS Presentation (continued)
The SETUP menu for the selected image
ItemFunctions
SETUPUse the ◄/► cursor buttons to switch each setting or use the ► cursor button to perform the functions as follows.
RETURNPress the ► cursor button or ENTER to return to the Thumbnail screen.
STARTSwitch to ON to set the selected image as the first image in the Slideshow. This setting information will be saved in the playlist.txt file (103).
STOPSwitch to ON to set the selected image as the last image in the Slideshow. This setting information will be saved in the playlist.txt file (103).
SKIPSwitch to ON to skip the selected image in the Slideshow. This setting information will be saved in the playlist.txt file (103).
ROTATEPress the ► cursor or the ENTER button to rotate the selected still image 90 degrees clockwise. This setting information will be saved in the playlist.txt file (103).
You can control the images on the Thumbnail screen with the remote control, 
control panel or Web Remote Control. The following functions can be supported 
while the Thumbnail screen is displayed.
Button operation
FunctionsRemote controlControl panelWeb Remote Control
▲/▼/◄/►▲/▼/◄/►[▲]/[▼]/[◄]/[►]Moves the cursor.
PAGE UPPAGE DOWN-[PAGE UP][PAGE DOWN]Switches pages.
ENTERINPUT[ENTER]
• Displays the selected image on the Full Screen mode when a cursor is on a Thumbnail image. • Displays the SETUP menu 
(below) for the selected image 
when a cursor is on a Thumbnail image number.
Button Operation