IBM Thinkpad Transnote Manual

							For a left-handed model
Step Screw (quantity) Screw cap Torque

1M2.5×3 mm,
nylon-coated (2)
39.2 Ncm
(4 kgfcm)

3M2.5×3 mm,
nylon-coated (1)39.2 Ncm
(4 kgfcm)
When installing:
When installing part
Ain the preceding figure, fit the
screw-hole plate and the claw into the square holes on the
bottom side of
A(
a) and then slide
Ain the direction
of the arrow
b. Then tighten the screw.
(continued)
Removing and replacing a FRU
ThinkPad TransNote77 
						

							Step Screw (quantity) Screw cap Torque

5M2.5×3 mm,
nylon-coated (1)
39.2 Ncm
(4 kgfcm)

6M2.5×3 mm,
nylon-coated (1)
39.2 Ncm
(4 kgfcm) Removing and replacing a FRU
78ThinkPad TransNote 
						

							1080 Computer side
Screw removal notice:When removing the computer
side from the Endurimer or
leather cover, remove only the
screws marked with″>″beside
the screw holes.
Step Screw (quantity) Screw cap Torque

1aM2.5×3 mm,
nylon-coated (1)none 39.2 Ncm
(4 kgfcm)

1M2.5×3 mm,
nylon-coated (3)
39.2 Ncm
(4 kgfcm)

2M2.5×4.5 mm,
nylon-coated (1)39.2 Ncm
(4 kgfcm)
(continued) vBattery pack(1010)
vHard-disk drive and hard-disk drive cover(1040)
vDigital-pen holder kit(1070)
Removing and replacing a FRU
ThinkPad TransNote79 
						

							(continued)
Removing and replacing a FRU
80ThinkPad TransNote 
						

							Removing and replacing a FRU
ThinkPad TransNote81 
						

							1090 ThinkScribe digital notepad
assembly
Screw removal notice:When removing the computer
side from the Endurimer or
leather cover, remove only the
screws marked with″>″beside
the screw holes.
Step Screw (quantity) Screw cap Torque

1M2.5×3 mm,
nylon-coated (3)
39.2 Ncm
(4 kgfcm)

1aM2.5×3 mm,
nylon-coated (2)none 39.2 Ncm
(4 kgfcm)
(continued) vBattery pack(1010)
vHard-disk drive and hard-disk drive cover(1040)
vDigital-pen holder kit(1070)
Removing and replacing a FRU
82ThinkPad TransNote 
						

							Note:In procedure
3, remove the base plate tape gently
in the direction of the arrow to avoid damaging the
copper sheet under the tape; it is to be reused.
When installing:Align the right edge of the base plate
tape (
a)tothe
b-part of the base
plate, as shown in the following figure.
(continued)
Removing and replacing a FRU
ThinkPad TransNote83 
						

							Note for a non-English model
Before attaching new digitizer onto the Endurimer, do the
followings;
1. Wipe the surface of the digitizer sheet
agently with a
dry soft cloth to remove a stain or a dust on it.
2. Stick the digitizer label
bonto the digitizer sheet.
Removing and replacing a FRU
84ThinkPad TransNote 
						

							1100 Endurimer and system-digi cable
Notes about the optional leather covervScratching or discoloration of the leather cover is
not covered under warranty.
vWhen removing and replacing the leather cover,
be very careful not to scratch the surface of the
Endurimer material.
Do not subject the system-digi cable to tension, especially
at the base of the cables of the connectors shown in figure

a. Tension could cause the cable to snap.
Note:When replacing the Endurimer or the system-digi
cable, make sure that the black connector of the
system-digi cable is attached to the computer and
the white connector is attached to the digital
notepad assembly.
For the process of changing the cover from right-handed
orientation to left-handed orientation, see“4010 Changing
the orientation of a left- or right-handed model”on
page 124. vBattery pack(1010)
vHard-disk drive and hard-disk drive cover(1040)
vDigital-pen holder kit(1070)
vComputer side(1080)
vThinkScribe digital notepad assembly(1090)
Removing and replacing a FRU
ThinkPad TransNote85 
						

							1110 Audio card and speaker
After procedure
2, lay the LCD unit down and then turn
the computer side upside down.
(continued) vBattery pack(1010)
vHard-disk drive and hard-disk drive cover(1040)
vKeyboard(1050)
vBackup battery and sub-battery(1060)
vDigital-pen holder kit(1070)
vComputer side(1080)
Removing and replacing a FRU
86ThinkPad TransNote