IBM Thinkpad Transnote Manual

							7. Paste new velcro tapes
1on the bottom side of
ThinkScribe digital notepad and remove the old tapes

2as shown in the following figures.
Right-handed model to left-handed model
Left-handed model to right-handed model
(continued)
Removing and replacing a FRU
ThinkPad TransNote127 
						

							8. Paste new tape for digitizer
1and digitizer base
tape
2on the bottom side of the computer side, and
then remove the other one
3.
Right-handed model to left-handed model
Left-handed model to right-handed model
9. Install the system-digi cable to the new Endurimer or
leather cover. (See“1100 Endurimer and system-digi
cable”on page 85.)
Note:When replacing the Endurimer or the
system-digi cable, make sure that the black
connector of the system-digi cable is attached
to the computer and the white connector is
attached to the digital notepad assembly.
(continued)
Removing and replacing a FRU
128ThinkPad TransNote 
						

							10. Install the computer side to the new Endurimer or
leather cover as follows;
a. Connect the system-digi cable to the computer
side and then paste new system board plate.
b. Paste the new tape (Tape for digitizer 2) aligning
the″┌″marks on the base plate.
(continued)
Removing and replacing a FRU
ThinkPad TransNote129 
						

							c. Tighten the screws and paste the screw caps.
Screw holes for a left-handed model.
Screw holes for a right-handed model.
Screw hole for both models.
(continued)
Removing and replacing a FRU
130ThinkPad TransNote 
						

							11. Install the digital notepad to the new Endurimer or
leather cover doing as follows;
a. Connect the system-digi cable
1to the digital
notepad and then paste the digitizer plate
2.
b. Paste the new tape (Tape for digitizer 2)
3
aligning the┌marks on the digitizer base plate.
(continued)
Removing and replacing a FRU
ThinkPad TransNote131 
						

							c. Tighten the screws and paste the screw caps.
Screw holes for a left-handed model.
Screw holes for a right-handed model.
12. Install the digital-pen holder kit. (See“1070
Digital-pen holder kit”on page 75.)
Removing and replacing a FRU
132ThinkPad TransNote 
						

							Locations
Front view

1TrackPoint buttons

2Latch

3System status indicators

4Power switch (computer side)

5Mini PCI Card slot

6Reset switch (computer side)

7DIMM slot

8ThinkPad button

9FlipTouch control button

10Mute button

11Battery pack

12Battery pack latch

13TrackPoint buttons

14Microphone jack

15Infrared port

16Built-in monaural speaker

17Built-in microphone

18Stereo line-in jack

19Stereo headphone jack

20Digital pen

21ThinkScribe digital notepad (see“ThinkScribe
digital notepad”on page 135.)
Locations
ThinkPad TransNote133 
						

							Rear view

1CompactFlash card slot

2CompactFlash card eject button

3Modem connector

4Network connector

5Universal serial bus (USB) connector

6External-monitor connector

7Power jack

8Security keyhole

9Port replicator connector

10PC card slot

11Hard-disk drive
Locations
134ThinkPad TransNote 
						

							ThinkScribe digital notepad

1Status display

2Error indicator light

3ThinkScribe reset switch

4Page selector

5Ink Files selector

6Actions selector

7Activity indicator light

8ThinkScribe power button

9Page Forward pen button

10Page Backward pen button

11Cancel pen button

12OK pen button

13Ink refill trays

14Pen holder
Locations
ThinkPad TransNote135 
						

							Parts list
Overall
26 27
28
3312
3
14
c c
b
35
16
15
17
a
a13
e d 1810 22
6
7
9 8
5
12
11
19
g
f
29
4
20
24
23
21
25
30
31 34
32
Parts list
136ThinkPad TransNote