HP Photosmart C6383 User Manual

3.Press the down arrow button until  View Network Settings is highlighted, and then
press  OK.
4. Do one of the following:
•To display wired network settings , press the down arrow button until Display
Wired Summary  is highlighted, and then press  OK.
• To display wireless network settings , press the down arrow button until
Display Wireless Summary  is highlighted, and then press  OK.
• To print the network configuration page , press the down arrow button until
Print Network Configuration Page  is...

3.Press the down arrow button until  Wireless Radio is highlighted, and then press
OK .
4. Press the down arrow button to highlight  On or  Off , and then press  OK.
Print the wireless network test
The wireless network test performs a series of diagnostic tests to determine whether
network setup is successful. If an issue is detected, a recommendation on how to correct
the issue will be included on the printed report. You can print the wireless network test at
any time.
To print the wireless test...

3.Press the down arrow button until  Advanced Setup is highlighted, and then press
OK .
Press the down arrow button until  Set Link Speed is highlighted, and then press
OK .
4. Press the down arrow button to select the link speed that matches your network
hardware, and then press  OK to confirm the setting.
• Automatic
• 10-Full
• 10-Half
• 100-Full
• 100-Half
Change IP settings
The default setting for the IP settings is  Automatic, which sets the IP settings
automatically. However, if you are an...

Related topics
•“
View and print network settings” on page 37
•“
Network configuration page definitions” on page 42
Use the Embedded Web Server
If your computer is connected to an HP All-in-One on a network, you can access the
Embedded Web Server that resides in the  HP All-in-One. The Embedded Web Server is
a Web-based user interface that provides so me options not available on the HP All-in-
One control panel like advanced network security options. The Embedded Web Server
also enables you to monitor...

Use the Embedded Web Server to modify network settings
The Embedded Web Server gives you an intuitive interface to your network connection
parameters.
To access the Embedded Web Server setup wizard
1.Print a network configuration page to find the IP address for the product.
2. In the  Address  box in your Web browser on your computer, type the IP address of
the product, as shown on the network settings page. For example, http://
192.168.1.101.
The Embedded Web Server  Home page appears, showing...

General network settings
The following table describes the general network settings shown on the network
configuration page.
ParameterDescription
Network StatusStatus of the HP All-in-One:
•Ready: The HP All-in-One is ready  to receive or transmit data.
•Offline: The HP All-in-One is not currently connected to the network.
Active connection
typeNetwork mode of the HP All-in-One:
•Wired: The HP All-in-One is connected by Ethernet cable to an IEEE
802.3 network.
•Wireless : The HP All-in-One is connected...

Wired (802.3) network settings
The following table describes the 802.3 wired settings shown on the network configuration
page.
ParameterDescription
Hardware
Address (MAC)The Media Access Control (MAC) address that identifies the HP All-in-One.
This is a unique 12-digit identification number assigned to networking
hardware for identification, including routers, switches, and other such
devices. No two pieces of hardware have the same MAC address.
NOTE:Some Internet service providers (ISPs) require that...

ParameterDescription
Link
ConfigurationThe speed at which data is transmitted over a network. Speeds include 10TX-
Full , 10TX-Half , 100TX-Full , and 100TX-Half . When set to  None, networking
is disabled.
Total Packets
transmittedThe number of packets transmitted by  the HP All-in-One without error since
it has been turned on. The counter clears after the HP All-in-One is turned
off. When a message is transmitted over a packet-switching network, it is
broken up into packets. Each packet contains the...

ParameterDescription
•Manual: The configuration parameters are set manually, such as a static
IP address.
•Not Specified : The mode used when the HP All-in-One is initializing.
DNS serverThe IP address of the domain name service (DNS) for the network. When you
use the Web or send an e-mail message, you use a domain name to do it.
For example, the URL http://www.hp.c om contains the domain name hp.com.
The DNS on the Internet translates the domain name into an IP address.
Products use the IP addresses to...

ParameterDescription
number. Value is from 1 to 14; countries/regions might limit the range of
approved channels.
•(number): Value ranging from 1 to 14, depending on country/region.
•None: No channel is in use.
•Not Applicable : The WLAN is disabled or this parameter does not apply
to this network type.
NOTE: In ad hoc mode, if you are not able to receive or transmit data
between your computer and the HP All-in-One, make sure that you are using
the same communication channel on your computer and the HP...