HP Photosmart C6383 User Manual

❑Broadband Internet access (optional but recommended) such as cable or DSL.
❑ If you connect the HP All-in-One on a wireless network that has Internet access, HP
recommends that you use a wireless router (access point or base station) that uses
Dynamic Host Configuration Protocol (DHCP).
❑ Network name (SSID).
❑ WEP key or WPA Passphrase (if needed).
Connect to an integrated wireless WLAN 802.11 network
The Wireless Setup Wizard provides an easy way to connect the HP All-in-One to your
network. You can...

3.Press the down arrow button until  Network is highlighted, and then press  OK.
4. Press the down arrow button to highlight  Wireless Setup Wizard, and then press
OK .
This runs the  Wireless Setup Wizard . The setup wizard searches for available
networks, and then displays a list of detected network names (SSIDs). The networks
with the strongest signal appear first, the weakest appear last.
5. Press the down arrow button to highlight the name of the network you wrote down in
step 1, and then press...

To connect the product with SecureEasySetup
1.Activate SecureEasySetup  on your wireless router or access point.
2. Press  Setup.
3.Press the down arrow button until  Network is highlighted, and then press  OK.
4. Press the down arrow button to highlight  Wireless Setup Wizard, and then press
OK .
5. Follow the onscreen prompts on the display to complete the connection.
6. When the product connects successfully to the network, go to your computer to install
the software on each computer that will use...

OR
▲Use an ad hoc network profile on your computer to connect to the product. If your
computer is not currently configured with an ad hoc network profile, consult the Help
file for your computer Operating System for the proper method to create an ad hoc
profile on your computer. Once the ad hoc network profile has been created, run the
Wireless Setup Wizard  from the Network menu on the HP All-in-One and select the
ad hoc network profile you created on your computer.
NOTE: An ad hoc connection can be...

5.Select the  Use Windows to configure my wireless network settings  check box.
6. Click  Add, and then do the following:
a .In  Network name (SSID)  box, type in a unique network name of your choice.
NOTE:The network name is case sensitive, so it is important to remember
any uppercase (capital) and lowercase (small) letters.
b . If there is a  Network Authentication  list, select Open. Otherwise, go to the next
step.
c .In the  Data encryption  list, select WEP.
NOTE: It is possible to create a network...

•Network name (SSID) : Mynetwork (example only)
NOTE:You should create a network name that is unique and easy for you to
remember. Just remember that the network name is case-sensitive. Therefore,
you must remember which letters are uppercase and lowercase.
• Communication mode : ad hoc
• Encryption : enabled
Connect to a wireless ad hoc network
You can use the Wireless Setup  Wizard to connect the HP All-in-One to a wireless ad
hoc network.
To connect to a wireless ad hoc network
1. Press  Setup....

d. Press the down arrow button until  Ad Hoc is highlighted, and then press  OK.
e . Press the down arrow button until  Yes, my network uses WEP encryption  is
highlighted, and then press  OK. The visual keyboard displays.
If you do  not want to use WEP encryption, press the down arrow button until  No,
my network does not use encryption  is highlighted, and then press OK. Go to
step 7.
6. If prompted, enter your WEP key as follows. Otherwise go to step 7.
a. Use the arrow buttons to highlight a letter...

To install the Windows HP Photosmart Software
1.Quit all applications running on your computer, including any virus detection software.
2. Insert the Windows CD that came with the product into the CD-ROM drive on your
computer and follow the onscreen instructions.
3. If a dialog box about firewalls appears, follow the instructions. If you see firewall pop-
up messages, you must always accept or allow the pop-up messages.
4. On the  Connection Type  screen, select Through the network , and then click...

3.Install the software for a network connection, choose  Add a product, and then
choose  Through the network .
4. When the installation is complete, open  Printers and Faxes (or Printers ) in the
Control Panel  and delete the printers from the previous USB installation.
To change a USB connection to an integrated wireless WLAN 802.11 connection
1. Unplug the USB connection from the back of the product.
2. Press  Setup.
3.Press the down arrow button until  Network is highlighted, and then press  OK.
4....

This section contains the following topics:
•
Use the Wireless Setup Wizard
•
View and print network settings
•
Restore network defaults
•
Turn the wireless radio on and off
•
Print the wireless network test
Use the Wireless Setup Wizard
The Wireless Setup Wizard provides an easy way to set up and manage a wireless
connection to the HP All-in-One.
To run the Wireless Setup Wizard
1. Press  Setup.
2.Press the down arrow button until  Network is highlighted, and then press  OK.
3. Press the down arrow...