HP P2055 Manual

Status-light patterns (HP LaserJet P2030 Series Printers
only)
Table 7-13  Status-light legend
Symbol for light off
Symbol for light on
Symbol for light blinking
Table 7-14  Control-panel light messages
Light statusState of the productAction
Initialization/Startup
While in the Startup state, the Go, Ready,
and Attention lights cycle (at the rate of
500 ms) one after another.
Reconfiguration Initialization
During the product start up, you can
request special initialization sequences
that reconfigure the...

Light statusState of the productAction
Ready
The product is ready with no job activity.To print a Configuration page, press and
hold the Go button for 5 seconds while
the device Ready light is on and no other
jobs are printing.
Processing Data
The product is processing or receiving
data. To cancel the current job, press the
Cancel
 button.
Table 7-14   Control-panel light messages (continued)
210 Chapter 7   Solve problems ENWW 

Light statusState of the productAction
Manual Feed or Continuable Error
This state can be reached in the following
circumstances:
● Manual feed
● General continuable error
● Memory configuration error
● Personality/Job related errorTo recover from the error and print
whatever data is possible, press the 
Go
button.
If the recovery is  successful, the product
goes to the Processing Data state and
completes the job.
If the recovery is unsuccessful, the
product returns to the Continuable Error
state....

Light statusState of the productAction
Fatal Error●Turn off the product, wait 10
seconds, and turn on the product.
● If you are unable to resolve the
problem, contact HP. See
Customer support on page 287.
Toner Low
The Go, Ready, and Attention lights act
independently of the Toner Low state. Order a new print cartridge.
Table 7-14
  Control-panel light messages (continued)
212 Chapter 7   Solve problems ENWW 

Light statusState of the productAction
Toner Missing
The print cartridge has been removed
from the product.Reinsert the print cartridge in the
product.
JamClear the jam. See Clear jams
on page 230.
Table 7-14  Control-panel light messages (continued)
ENWW Status-light patterns (HP LaserJet P2030 Series Printers only) 213 

Light statusState of the productAction
Paper OutLoad paper or other media.
Paper Mount
The loaded paper or other media is not
supported.Load acceptable paper or other media.
See 
Supported paper and print media
on page 32
.
Press the Go  button to override the
condition.
Table 7-14   Control-panel light messages (continued)
214 Chapter 7   Solve problems ENWW 

Status-alert messages (HP LaserJet P2030 Series Printers
only)
Status-alert messages appear on the computer scr een when the product has certain problems. Use the
information in the following table to solve these problems.
Alert messageDescriptionRecommended action
10.X Supply memory errorThe product has experienced a print cartridge
error.
The two cartridge memory contacts on the
right-rear side of the print cartridge contact
the reader contacts on the product.1. Make sure that a genuine HP print...

Alert messageDescriptionRecommended action
Door OpenOpening the front door opens the front door
switch (SW301) and disables the +24 V to the
high-voltage contacts on the print cartridges.1.Remove the left cover, and then open
and close the front door. Determine if
SW301 closes when the door closes.
2. Make sure that the two connectors from
the engine control PCA to the switch are
securely installed on the switch
contacts.
3. Replace the front door switch (SW301).
if the message persists. See...

Alert messageDescriptionRecommended action
Jam in output binThis error occurs if the duplex reverse
photosensor (PS918) or fusing exit sensor
(PS915) detect unexpected paper.1.Make sure that the paper meets
specifications. See 
Specifications
on page 291.
2. Open the rear duplex jam-release door
and clear any visible paper. Verify that
the duplex-release sensor flag moves
freely. You might need a pen light to
observe the flags.
3. Open the face-up output door, and verify
that the exit sensor flag in the...

Alert messageDescriptionRecommended action
Load paperThe product did not detect paper in Tray 1 or
Tray 2. PS916 detects paper in Tray 1.
PS914 detects paper in Tray 2. See 
Figure
7-7 Components in the print cartridge cavityon page 199.
1.Verify that paper is loaded in the input
tray.
2. Make sure that the photosensor flags
are not hindered.
3. Make sure that connectors J205 (for
Tray 1) and J204 (for Tray 2) on the
engine controller PCA are seated.
Manual feedThe product is set for manual feed...