HP P 1100 Service Manual

							Left cover
NOTE:For the HP LaserJet Professional P1100w Printer series, removing the left cover also removes
the control panel.
Before proceeding, remove the following components:
●Input tray or main-input tray. See 
Input tray or main-input tray on page 40
.
● Output bin tray extension. See 
Output bin tray extension on page 41
.
● Front cover. See 
Front cover on page 42.
Remove the left cover
1.
Use the figure below to locate the tabs (callout 1) on the cover.
Figure 2-10  Remove the left cover (1 of 5)
1
ENWW Covers 43 
						

							2.Open the cartridge door, release one tab (callout 1) and then remove the left plate (callout 2).
Figure 2-11   Remove the left cover (2 of 5)
1
2
3.HP LaserJet Professional P1100 Printer series : Remove the light pipe (callout 1).
HP LaserJet Professional P1100w Printer series : Remove the light pipe (callout 1), wireless
button (callout 2), and the cancel button (callout 3).
Figure 2-12   Remove the left cover (3 of 5)
1
2
3
44 Chapter 2   Removal and replacement ENWW 
						

							4.Remove one screw (callout 1).
Figure 2-13  Remove the left cover (4 of 5)
1
5.Release three tabs (callout 1) at the top, rear, and bottom of the cover, slide the cover toward the
front of the product to release two tabs (callout 2), and then remove the left cover (callout 3).
Figure 2-14  Remove the left cover (5 of 5)
1
3
2
ENWW Covers 45 
						

							Right cover
Before proceeding, remove the following components:●Input tray or main-input tray. See 
Input tray or main-input tray on page 40.
● Output bin tray extension. See 
Output bin tray extension on page 41.
● Front cover. See 
Front cover on page 42.
Remove the right cover
1.
Use the figure below to locate the tabs (callout 1) on the cover.
Figure 2-15   Remove the right cover (1 of 3)
1
2.Remove on screw (callout 1), and open the print-cartridge door.
Figure 2-16   Remove the right cover (2 of 3)
1
46 Chapter 2   Removal and replacement ENWW 
						

							3.Release three tabs (callout 1) at the top, rear, and bottom of the cover, slide the cover toward the
front of the product to release two tabs (callout 2), and then remove the left cover (callout 3).
Figure 2-17  Remove the right cover (3 of 3)
2
3
1
ENWW Covers 47 
						

							Cartridge door
Before proceeding, remove the following components:●Input tray or main-input tray. See 
Input tray or main-input tray on page 40.
● Output bin tray extension. See 
Output bin tray extension on page 41.
● Front cover. See 
Front cover on page 42.
● Left cover. See 
Left cover on page 43.
● Right cover. See 
Right cover on page 46
.
Remove the cartridge door
1. Open the cartridge door, and then release the tabs on the link arms (callout 1).
Figure 2-18   Remove the cartridge door (1 of 2)
1
48 Chapter 2   Removal and replacement ENWW 
						

							2.Release two pins (callout 1), and then remove the cartridge door (callout 2).
Figure 2-19  Remove the cartridge door (2 of 2)
1
2
ENWW Covers 49 
						

							Face-down cover
Before proceeding, remove the following components:●Input tray or main-input tray. See 
Input tray or main-input tray on page 40.
● Output bin tray extension. See 
Output bin tray extension on page 41.
● Front cover. See 
Front cover on page 42.
● Left cover. See 
Left cover on page 43.
● Right cover. See 
Right cover on page 46
.
● Cartridge door assembly. See 
Cartridge door on page 48
Remove the face-down cover
1.
Release two tabs (callout 1), and slightly separate the face-down cover from the rear cover.
Figure 2-20   Remove the face-down cover (1 of 2)
1
50 Chapter 2   Removal and replacement ENWW 
						

							2.Rotate the bottom of the cover away from the product and then remove the cover.
Reinstallation tip When you reinstall the cover, make sure that the tabs on the cover fit into the
slots in the top of the chassis near the print-cartridge opening.
It might be easier to reinstall the cover if you remove the rear cover first. See 
Rear cover
on page 52 .
Figure 2-21  Remove the face-down cover (2 of 2)
ENWW Covers 51 
						

							Rear cover
Before proceeding, remove the following components:●Input tray or main-input tray. See 
Input tray or main-input tray on page 40.
● Output bin tray extension. See 
Output bin tray extension on page 41.
● Front cover. See 
Front cover on page 42.
● Left cover. See 
Left cover on page 43.
● Right cover. See 
Right cover on page 46
.
● Face-down cover. See 
Face-down cover on page 50
.
Remove the rear cover
1. Remove one screw with washer (callout 1).
Figure 2-22   Remove the rear cover (1 of 2)
1
52 Chapter 2   Removal and replacement ENWW