HP Officejet Pro 8600 Premium User Manual

3.Slide the media guides in the tray to adjust them for the media size that you have
loaded, and then reinsert the tray.
4. Pull out the extension on the output tray.
Load custom-size media
To load custom-size media
Use these instructions to  load custom-size media.
CAUTION:Use only custom-size media  that is supported by the printer. For more
information, see 
Media speci fications.
NOTE:Load only plain media in Tray 2.
1.Pull out Tray 1.
2.Insert the media print-side do wn in the center of the tray....

3.Slide the media guides in the tray to adjust them for the media size that you have
loaded, and then reinsert the tray.
4.Pull out the extension on the output tray.
Insert a memory device
If your digital camera uses a memory card to  store photos, you can insert the memory
card into the printer to print or save your photos.
CAUTION: Attempting to remove a memory card  while it is being accessed can
damage files on the card. You can safely remove a card only when the photo light
is not blinking. Also,...

NOTE:You cannot insert more  than one memory card in the printer.
To connect a storage device
1.If you are connecting a di gital camera, change the USB mode of the camera to
storage mode, and then connect one end of the USB cable to the camera.
NOTE: Different cameras use different terms to describe  the storage mode.
For instance, some cameras have a digital camera setting and a disk drive
setting. In this instance, the disk drive setting is the storage mode setting. If
storage mode does not work on...

Slide the duplexer into the back of the printer until the unit locks into place. Do not
press the buttons on either side of the duplexer when installing the unit; use them only
for removing the unit from the printer.
Install Tray 2
NOTE: This feature is available with some models of the printer.
Tray 2 can hold up to 250 sheets of plain paper. For ordering information, see HP
supplies and accessories.
To install Tray 2
1.Unpack the tray, remove the packing tapes  and materials, and move the tray to the...

To load Tray 2
1.Pull the tray out of the printer by grasping under the front of the tray.
2.Insert the paper print-side down  in the center of the tray. Make sure the stack of
paper aligns with the line on the width guide, and does not exceed the line marking
on the guide.
NOTE: Tray 2 can be loaded only with plain paper.
3.Slide the media guides in the tray to adjust them for the size that you have loaded.
Install the accessories 31
 

4.Gently reinsert the tray.
5. Pull out the extension on the output tray.
Configure trays
NOTE: Tray 2 is an optional accessory.  For ordering information, see Order
printing supplies online.
To configure the trays, you must have Tray 2 installed and turned on.
By default, the printer draws media from Tray 1. If Tray 1 is empty, the printer draws
media from Tray 2 (if it is installed and loaded with media). You can change this default
behavior by using the following features:
•Tray Lock:  Use this...

I want to...Follow these steps
Load media in both trays but have the printer
pick media from a specific tray first.
•Load media in Tray 1 and Tray 2.
•Make sure default tray is set to the
appropriate tray.
To configure the trays
1. Make sure the printer is turned on.
2. Touch 
 (right arrow), touch  Setup, touch  Preferences , and then select  Default
Tray  or Tray Lock .
3. Click  OK or Apply  after changing the desired tray settings.
Turn on accessories in the printer driver
•To turn on accessories...

To clean the scanner glass
1.Turn the printer off. For more information, see 
Turn the printer off.
2. Lift the scanner lid.
3. Clean the glass and the glass strip by using a soft, lint-free cloth that has been
sprayed with a mild glass cleaner. Dry the glass with a dry, soft, lint-free cloth.
CAUTION: Use only glass cleaner to clean the scanner glass. Avoid cleaners
that contain abrasives, acetone, benzene, and carbon tetrachloride, all of which
can damage the scanner glass. Avoid isopropyl alcohol...

cover to access the pick assembly inside the automatic document feeder, clean the
rollers or separator pad, and then close the cover.
To clean the rollers or separator pad
1. Remove all originals from the document feeder tray.
2. Lift the automatic document feeder cover (1).
This provides easy access to the ro llers (2) and separator pad (3).
11
22
33
1 Automatic document feeder cover
2Rollers
3 Separator pad
3.Lightly dampen a clean lint-free cloth  with distilled water, then squeeze any excess
liquid...

2Print
Most print settings are automatically handled by the software application. Change the
settings manually only when you want to change print quality, print on specific types of
paper, or use special features. For more information about selecting the best print
media for your documents, see 
Select print media.
Choose a print job to continue:
Print documents
Print brochures
Print on envelopes
Print photos
Print on special and custom-size paper
Print borderless documents
Print documents
Follow the...