HP LaserJet P3005 User Manual

							
HP LaserJet P3005, P3005d, P3005n, P3005dn, P3005x, laserkirjoitin on käyttäjän kannalta turvallinen
luokan 1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen
ulkopuolelle. Laitteen turvallisuusluokka on määrit etty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING !
Om apparaten används på annat sätt än i bruksanv isning specificerats, kan användaren utsättas för
osynlig laserstrålning, som över skrider gränsen för laserklass 1.
HUOLTO
HP LaserJet P3005, P3005d, P3005n, P3005dn, P3 005x - kirjoittimen sisällä ei ole käyttäjän
huollettavissa olevia kohteita. Laitteen saa avata  ja huoltaa ainoastaan sen huoltamiseen koulutettu
henkilö. Tällaiseksi huoltotoimenpiteeksi ei  katsota väriainekasetin vaihtamista, paperiradan
puhdistusta tai muita käyttäjän käsikirjassa lueteltuja , käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia,
jotka voidaan suorittaa  ilman erikoistyökaluja.
VARO !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömällelasersäteilylle laitteen ollessa
toiminnassa. Älä katso säteeseen.
VARNING !
Om laserprinterns skyddshölje öppnas då apparat en är i funktion, utsättas användaren för osynlig
laserstrålning. Betrakta ej strålen. Tiedot laitte essa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 775-795 nm Teho 5 m W Luokan 3B laser.
ENWW Safety statements 179
 
						

							
180 Appendix D   Regulatory information ENWW
 
						

							
E Work with memory and print servercards
This section explains the memo ry features of the device and provides steps for expansion.
●
Overview
●
Install memory
●
Check DIMM installation
●
Save resources (permanent resources)
●
Enable memory for Windows
●
Use HP Jetdirect print server cards
ENWW 181
 
						

							
Overview
One dual inline memory module (DIMM) slot is available for upgrading the device with the following
items:
● More device memory—DIMMs—is available in 32, 48, 64, 128, and 256 MB.
● Other DIMM-based device lang
uages and device options.
For ordering information, see 
Order parts, accessories, and supplies .
NOTESingle inline memory modules (SIMMs) used  in previous HP LaserJet devices are not
compatible with the device.
The device also has one EIO slot for expanding the de vice networking capabilities. The EIO slot can be
used to upgrade the device with an additional netw ork connection, such as a wireless print server,
network card, or a connectivity card for a serial or AppleTalk connection.
NOTE Some HP LaserJet P3005 series devices come  with a network device already installed.
The EIO slot may be used to provide networking ca pabilities in addition to those already built into
the device.
To find out how much memory is inst alled in the device, or to find out what is installed in the EIO slots,
print a configuration page. See 
Use information pages .
182 Appendix E   Work with memory and print server cards ENWW
 
						

							
Install memory
You might want to add more memory to the device if you often print complex graphics, print PostScript
(PS) documents, or use many do wnloaded fonts. Added memory also give s you more flexibility in
supporting job-storage features, such as quick copying. 
Install device memory
CAUTION Static electricity can damage DIMMs.  When handling DIMMs, either wear an
antistatic wrist strap or frequently touch the su rface of the DIMM antistatic package, then touch
bare metal on the device.
The HP LaserJet P3005 devices come with one DIMM slot. If desired, you can replace a DIMM installed
in the slot with a higher memory DIMM.
If you have not already done so, print a configuration page to find out how much memory is installed in
the device before adding more memory. See 
Use information pages .
1. After the configuration page has printed, turn the device off and disconnect the power cord.
2.Disconnect all interface cables.
ENWW Install memory 183
 
						

							
3.Remove the right side panel by sliding it towards  the rear of the device until the side slides from
the device.
4. Open the access door by pulling on the metal tab.
5.Remove the DIMM from the antistatic package.
CAUTION To reduce the possibility of damage ca used by static electricity, always wear
an electrostatic discharge (ESD) wrist strap or  touch the surface of the antistatic package
before handling DIMMs.
184 Appendix E   Work with memory and print server cards ENWW
 
						

							
6.Hold the DIMM by the edges, and align the notc hes on the DIMM with the DIMM slot. (Check that
the locks on each side of the DIMM slot are open.)
7. Press the DIMM straight into the slot, and press fi rmly. Make sure the locks on each side of the
DIMM snap into place.
NOTE To remove a DIMM, first release the locks.
8.Close the access door, and press firmly until it snaps into place.
ENWW Install memory 185
 
						

							
9.To replace the right side panel, line up the alignment arrows and slide the panel toward the front
of the device until it latches into place.
10.Reconnect the interface cabl e(s) and the power cord.
11.Turn the device on.
186 Appendix E   Work with memory and print server cards ENWW
 
						

							
Check DIMM installation
After installing the DIMM, make sure that the installation was successful.
Verify that DIMM is installed correctly
1. Turn the device on. Check that th e Ready light is illuminated after the device has gone through the
startup sequence. If an error message appears,  a DIMM might have been incorrectly installed.
See 
Control-panel messages .
2. Print a configuration page (see 
Use information pages ).
3. Check the memory section on the configuration page  and compare it to the configuration page that
was printed before the memory installation. If th e amount of memory has not increased, the DIMM
might not be installed correctly, or the DIMM might  be defective. Repeat the installation procedure.
If necessary, install a different DIMM.
NOTE If you installed a device language (persona lity), check the Installed Personalities and
Options section on the configuration page. Th is area should list the new device language.
ENWW Check DIMM installation 187
 
						

							
Save resources (permanent resources)
Utilities or jobs that you download to the device sometimes include resources (for example, fonts,
macros, or patterns). Resources that are internally  marked as permanent remain in the device memory
until you turn the device power off.
Use the following guidelines if you use the page desc ription language (PDL) ability to mark resources
as permanent. For technical details, see an  appropriate PDL reference for PCL or PS.
● Mark resources as permanent only when it is absolutely necessary that they remain in memory
while the device power is turned on.
● Send permanent resources to the device only at th
e beginning of a print job and not while the device
is printing.
NOTE Overusing permanent resources or downloading them while the device is printing might
affect device performa nce or the ability to print complex pages.
188 Appendix E   Work with memory and print server cards ENWW