HP LaserJet P2055dn User Manual

NOTE:This mode is the recommended network configuration for the product.
1.Before turning on the product, connect the product directly to the network by inserting a network
cable into the product network port.
2. Turn on the product, wait 2 minutes, and then use the control panel to print a configuration page.
NOTE: Make sure that an IP address is listed on the configuration page before proceeding to the
next step. If an IP address is not present, reprint the configuration page.
3. Insert the product CD...

IP address
The product IP address can be set manually, or it can be configured automatically via DHCP, BootP, or
AutoIP.
Automatic configuration 1.On the control panel, press OK .
2. Use the arrow buttons to select  Network config., and then press OK.
3. Use the arrow buttons to select either  BOOTP or DHCP , and then press  OK.
4. Use the arrow buttons to select  Yes, and then press OK .
It may take several minutes before the automatic IP address is ready for use.
5. Use the Back or  Cancel button to...

Link speed setting
NOTE:Incorrect changes to the link speed setting might prevent the product from communicating with
other network devices. For most situations, the product should be left in automatic mode. Changes can
cause the product to power cycle. Changes should be made only while the product is idle.
1. On the control panel, press  OK.
2. Use the arrow buttons to select  Network config., and then press OK .
3. Use the arrow buttons to select  CFG LINK, and then press OK.
4. Use the arrow buttons...

42 Chapter 5   ConnectivityENWW
 

6 Paper and print media
●Understand paper and print media use
●
Supported paper and print media sizes
●
Custom paper sizes
●
Supported paper and print media types
●
Tray and bin capacity
●
Special paper or print media guidelines
●
Load trays
●
Configure trays
●
Use paper output options
ENWW 43
 

Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this
user guide. Paper or print media that does not meet these guidelines might cause the following problems:
●Poor print quality
● Increased jams
● Premature wear on the product, requiring repair
For best results, use only HP-brand paper and print media designed for laser printers or multiuse. Do
not use paper or print media made for inkjet printers. Hewlett-Packard...

Supported paper and print media sizes
This product supports a number of paper sizes, and it adapts to various media.
NOTE:To obtain best results, select the correct paper size and type in the printer driver before printing.
Table 6-1   Supported paper and print media sizes
Size and dimensionsTray 1Tray 2Optional 500-sheet
Tray 3Duplexer (duplex
models only)
Letter
216 x 279 mm (8.5 x 11 inches)
Legal
216 x 356 mm (8.5 x 14 inches)
A4
210 x 297 mm (8.27 x 11.69 inches)
A5
148 x 210 mm (5.83 x 8.27 inches)...

Size and dimensionsTray 1Tray 2Optional 500-sheet
Tray 3Duplexer (duplex
models only)
Envelope B5 ISO
176 x 250 mm (6.7 x 9.8 inches)   
Envelope C5 ISO
162 x 229 mm (6.93 x 9.84 inches)   
Envelope DL ISO
110 x 220 mm (4.33 x 8.66 inches)   
Envelope Monarch
98 x 191 mm (3.9 x 7.5 inches)   
Custom
76 x 127 mm to 216 x 356 mm
(3.0 x 5.0 inches to 8.5 x 14 inches)    
Custom paper sizes
This product supports a variety of custom paper sizes. Supported custom sizes are sizes that are within
the minimum-...

Supported paper and print media types
For a complete list of specific HP-brand paper that this product supports, go to www.hp.com/support/
ljp2050series.
Paper type (control panel)Paper type (printer driver)Tray 1Tray 2Optional 500-
sheet Tray 3Duplexer
(duplex
models only)
PLAIN 75–95 GPlain
LIGHT 60-74 GLight 60-74g
MID-WEIGHTMid-weight
HEAVY 111–130 GHeavy 111–130g 
EXTRA HEAVY 131–175 GExtra heavy 131–175g   
TRANSPARENCYMonochrome Laser
Transparency 
LABELSLabels   
LETTERHEADLetterhead...

Tray and bin capacity
Tray or binPaper typeSpecificationsQuantity
Tray 1PaperRange:
60 g/m
2 (16 lb) bond to 200 g/m2
(54 lb) bond
Maximum stack height: 5 mm
(0.3 inch)
Equivalent to 50 sheets of 75 g/
m
2 (20 lb) bond
EnvelopesLess than 60 g/m2 (16 lb) bond to
90 g/m2 (24 lb) bond
Up to 10 envelopes
LabelsMaximum 0.23 mm (0.009 inch)
thickMaximum stack height: 5 mm
(0.3 inch)
TransparenciesMinimum 0.13 mm (0.005 inch)
thickMaximum stack height: 5 mm
(0.3 inch)
Tray 2PaperRange:
60 g/m
2 (16 lb) bond to...