HP LaserJet M4345xs User Manual

Print Quality menu
NOTEValues shown with (default) are the factory-default values. Some men\
u items have
no default.
Table 2-15   Print Quality menu
Menu itemSub-menu itemValuesDescription
Set RegistrationTest PagePrint (button)Use Set Registration  to shift the margin alignment to
center the image on the page from top to bottom and
from left to right. You can also align the image on the
front with the image printed on the back.
Print a test page for setting the registration.
SourceAll trays
Tray :...

Menu itemSub-menu itemValuesDescription
Toner Density Choose from a range of
1 to 5. 3 is the default.Lighten or darken the print on the page. 1 is the
lightest and 5 is the darkest.
Calibration/Cleaning Auto CleaningEnabled
DisabledWhen auto-cleaning is on, the device prints a
cleaning page when the page count reaches the
value that is set in  Cleaning Interval.
Cleaning Interval1000
2000
5000
10000
20000Set the interval when the cleaning page should be
printed. The interval is measured by the number...

Troubleshooting menu
NOTEValues shown with (default) are the factory-default values. Some men\
u items have
no default.
Table 2-16   Troubleshooting menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Event Log  Print (button)This feature shows the event codes and
their corresponding engine cycles on the
display, and it allows you to print the full
event log.
Calibrate Scanner  Calibrate (button)Use this feature to compensate for offsets
in the scanner imaging system (carriage
head) for ADF and...

Menu itemSub-menu itemSub-menu itemValuesDescription
Paper Path Test Test Page Print (button)Generate a test page for testing paper
handling features. You can define the path
that is used for the test in order to test
specific paper paths.
Source All trays
Tray 1
Tray 2
(Additional trays are
shown, if applicable.)Specify whether the test page will be
printed from all trays or from a specific tray.
Destination All bins
Stacker Bin
Standard Output BinSelect the output option for the test page.
You can...

Menu itemSub-menu itemSub-menu itemValuesDescription
Finishing Paper
Path TestStaplesFinishing OptionsChoose from a list
of available options.Test paper handling features for the finisher.
Select the option that you want to test.
Media SizeLetter
Legal
A4
Executive (JIS)
8.5 x 13Select the paper size for the Finishing
Paper Path Test.
Media Type Select the paper type for the Finishing
Paper Path Test.
CopiesRange: 2-30,
Default=2Select the number of copies to include in
the Finishing Paper Path Test....

Menu itemSub-menu itemSub-menu itemValuesDescription
Component Test   Exercise individual parts independently to
isolate noise, leaking, or other issues. To
start the test, select one of the components.
The test will run the number of times
specified by the Repeat option. You might
be prompted to remove parts from the
device during the test. Press the  Stop
button to abort the test.
Print/Stop Test  Continuous value
from 0 to 60,000
milliseconds. The
default is 0
milliseconds.Isolate faults by stopping...

Resets menu
Table 2-17  Resets menu
Menu itemValuesDescription
Clear Local Address BookClear (button)Use this feature to clear all addresses from the address books that
are stored on the device.
Clear Fax Activity LogYes
No (default)Use this feature to clear all events from the Fax Activity Log.
Restore Factory Telecom SettingRestore  (button)Use this option to restore the telephone-related settings that are in
the Initial Setup  menu to factory default values.
Restore Factory SettingsRestore (button)Use...

Service menu
The Service menu is locked and requires a PIN for access. This menu is intended for use by
authorized service personnel.
56 Chapter 2   Control Panel ENWW
 

3Input/output (I/O)
This chapter describes how to configure certain network parameters on the device. The following
topics are covered:
●
USB configuration
●
Network configuration
ENWW 57
 

USB configuration
This device supports a USB 2.0 connection. You must use an A-to-B type USB cable for printing.
Figure 3-1  USB connection
1USB connector
2USB port (type B)
58 Chapter 3   Input/output (I/O) ENWW