HP LaserJet M3035xs MFP User Manual

Safety statements
Laser safety
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has
implemented regulations for laser products m anufactured since August 1, 1976. Compliance is
mandatory for products marketed in the United States . The device is certified as a “Class 1” laser product
under the U.S. Department of Health and Human  Services (DHHS) Radiation Performance Standard
according to the Radiation Control for Health and Safety Act of 1968. Since...

EMI statement (Taiwan)
Laser statement for Finland
Luokan 1 laserlaite
Klass 1 Laser Apparat
HP LaserJet M3027, M3027x, M3035, M3035xs, laserkirjoitin on käyttäjän kannalta turvallinen luokan
1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi estää lasersäteen pääsyn laitteen
ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN 60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän...

E Working with memory and print servercards
This section explains the device memory  features and provides steps for expansion.
●
Overview
●
Install memory
●
Check DIMM installation
●
Save resources (permanent resources)
●
Enable memory for Windows
●
Use HP Jetdirect print server cards
ENWW 231
 

Overview
One dual inline memory module (DIMM) slot is available for upgrading the device with the following
items:
● More memory—DIMMs are availabl
e in 64, 128, 256, and 512 MB.
● Other DIMM-based printer languages and printer options.
The device uses 100-pin 133 MHz DDR memory modu les. Extended data output (EDO) DIMMs are not
supported.
For ordering information, see 
Order parts, accessories, and supplies .
NOTESingle inline memory modules (SIMMs) used  in previous HP LaserJet printers are not...

Install memory
You might want to add more memory to the device if you often print complex graphics, print PostScript
(PS) documents, or use many do wnloaded fonts. Added memory also give s you more flexibility in
supporting job-storage features, such as quick copying. 
Install device memory
CAUTION Static electricity can damage DIMMs.  When handling DIMMs, either wear an
antistatic wrist strap or frequently touch the su rface of the DIMM antistatic package, then touch
bare metal on the device.
The HP...

3.Remove the right side panel by sliding it towards  the rear of the device until the side slides from
the device.
4. Open the access door by pulling on the metal tab.
5.Remove the DIMM from the antistatic package.
CAUTION To reduce the possibility of damage ca used by static electricity, always wear
an electrostatic discharge (ESD) wrist strap or  touch the surface of the antistatic package
before handling DIMMs.
234 Appendix E   Working with memory and print server cards ENWW
 

6.Hold the DIMM by the edges, and align the notc hes on the DIMM with the DIMM slot. (Check that
the locks on each side of the DIMM slot are open.)
7. Press the DIMM straight into the slot, and press fi rmly. Make sure the locks on each side of the
DIMM snap into place.
NOTE To remove a DIMM, first release the locks.
ENWW Install memory 235
 

8.Close the access door, and press firmly until it snaps into place.
9.To replace the right side panel, line up the alignment arrows and slide the panel toward the front
of the device until it latches into place.
10.Reconnect the interface cabl e(s) and the power cord.
11.Turn the device on.
236 Appendix E   Working with memory and print server cards ENWW
 

Check DIMM installation
After installing the DIMM, make sure that the installation was successful.
Verify that DIMM is installed correctly
1. Turn the device on. Check that th e Ready light is illuminated after the device has gone through the
startup sequence. If an error message appears,  a DIMM might have been incorrectly installed.
See 
Control-panel messages .
2. Print a configuration page (see 
Use information pages ).
3. Check the memory section on the configuration page  and compare it to the...

Enable memory for Windows
1.On the  Start menu,  Settings , and Printers  or Printers and Faxes .
2. Select this device and select  Properties.
3. On the  Configure  tab, click More.
4. In the  Total Memory  field, type or select the total amount of memory that is now installed.
5. Click  OK.
6. Go to 
Check DIMM installation .
238 Appendix E   Working with memory and print server cards ENWW