HP LaserJet 4250 User Manual

Control panel messageDescriptionRecommended action
DIFFERENT PAPER
SIZES IN JOBThe stapler cannot align the paper for
stapling if different paper sizes are in the
job. Printing continues but the job is not
stapled.If stapling is required, modify the job.
DUPLEXER ERROR
REMOVE DUPLEXER
Install duplexer
with power offThe optional duplexer has an error.Turn off the printer power and reattach
the optional duplexer. (Any print jobs at
the printer might be lost.)
EIO X disk
spinning upThe disk accessory in EIO...

Control panel messageDescriptionRecommended action
EIO X DISK IS
WRITE PROTECTED
To clear press 
alternates with

The EIO disk is protected, and no new
files can be written to it.Use the Device Storage Manager in
HP Web Jetadmin to disable the write
protection.
EIO X DISK NOT
INITIALIZED
To clear press 
alternates with

The file system has not been initialized.Use HP Web Jetadmin to initialize the
file system.
ENVELOPE FEEDER
EMPTY
alternates with
The envelope feeder is empty.Load envelopes in the...

Control panel messageDescriptionRecommended action
INTERNAL DISK FILE
OPERATION FAILED
To clear press 
alternates with

The requested operation could not be
performed. You might have attempted
an illegal operation, such as trying to
download a file to a non-existent folder.Try printing again to an existing folder.
INTERNAL DISK FILE
SYSTEM IS FULL
To clear press 
alternates with

The Internal disk is full.Delete files from the disk and then try
again. Use the Device Storage Manager
in HP Web Jetadmin to...

Control panel messageDescriptionRecommended action
LOAD TRAY XX
[TYPE][SIZE]
To continue press 
alternates with
Move tray switch to
CUSTOM
A job is sent that requires a specific type
and size that is not available in the tray
that is indicated.Move the tray switch to the CUSTOM
position if another tray is available.
LOAD TRAY XX
[TYPE][SIZE]
To continue press 
alternates with
Recommend move tray
switch to STANDARD
A job is sent that requires a specific type
and size that is not available in the tray
that...

Control panel messageDescriptionRecommended action
No job to cancelThe STOP button was pressed, but there
is no active job or buffered data to cancel.
The message is displayed for
approximately 2 seconds before the
printer returns to the ready state.No action necessary.
NON HP SUPPLY
INSTALLED
Economode disabledThe printer has detected that the print
cartridge is not a genuine HP supply.This message is displayed until you
install an HP cartridge or press the
override button 
 ( SELECT button).
If you...

Control panel messageDescriptionRecommended action
RAM DISK DEVICE
FAILURE
To clear press 
alternates with

The RAM disk had a critical failure and
can no longer be used.Contact an HP-authorized service or
support provider.
RAM DISK FILE
OPERATION FAILED
To clear press 
alternates with

The requested operation could not be
performed. You might have attempted
an illegal operation, such as trying to
download a file to a non existent folder.Try printing again to an existing folder.
RAM DISK FILE
SYSTEM IS...

Control panel messageDescriptionRecommended action
REPLACE CARTRIDGE
For help press 
alternates with

Pages remaining for this supply has
reached the low threshold. The printer
was set to stop printing when a supply
needs to be ordered.To continue printing, press  (SELECT
button) to exit the printer message then
press 
 (SELECT button). The message
becomes  ORDER CARTRIDGE LESS
THAN XXXX PAGES  (warning).
Follow the next steps to replace the
supply.
1. Open the top cover.
2. Remove print cartridge.
3....

Control panel messageDescriptionRecommended action
ROM DISK IS
WRITE PROTECTED
To clear press 
alternates with

The disk is protected, and no new files
can be written to it.Use the Device Storage Manager in
HP Web Jetadmin to disable the write
protection.
ROM DISK NOT
INITIALIZED
To clear press 
alternates with

The file system has not been initialized.Use HP Web Jetadmin to initialize the
file system.
SANITIZING DISK
% COMPLETE
Do not power off
alternates with
CLEANING DISK
% COMPLETE
For help press A...

Control panel messageDescriptionRecommended action
STAPLER OUT OF
STAPLESThe stapler in the optional stapler/
stacker is out of staples. The printer
behavior depends on how STAPLES
OUT  is configured in the  Output Setup
submenu.● If STAPLES OUT=STOP , the
printer stops printing until you refill
the stapler or press Select. This is
the default setting.
● If STAPLES OUT=CONTINUE ,
printing continues, but the job is not
stapled.
Replace the staple cartridge. For
information about replacing the staple...

Control panel messageDescriptionRecommended action
Unable to store job

alternates with
The print job named cannot be stored
due to a memory, disk, or configuration
problem.Correct the error and then try again to
store the job.
UNSUPPORTED DATA ON
[FS] DIMM IN SLOT X
To clear press The data on the DIMM is not supported.
[FS] stands for either ROM or FLASH.The DIMM may need to be replaced.
Turn the printer power off before
removing it.
Press 
 (SELECT button) to continue.
USE TRAY XX
[TYPE][SIZE]
To...