HP LaserJet 3050z User Manual

Change the number of copies
You can choose to have the default number of copies be any number from 1 to 99.
To change the number of copies for the current job (HP LaserJet 3050 all-in-one)
1. On the all-in-one control panel, use the alphanumeric buttons to type the number of copies
(between 1 and 99) that you want to make for your current job.
2. Press  Start Copy to begin copying your job.
NOTE The change in the setting remains active for  about two minutes after the copy job
has been completed. During...

Scan: How do I?
Use this section to answer scanning questions.
Use HP LaserJet Scan
1.In the Hewlett-Packard program group, select  Scan to start HP LaserJet Scan.
NOTE Pressing Start Scan on the all-in-one control panel also starts HP LaserJet Scan.
2.Choose the action that you want to accomplish.
●Select a destination to begin scanning immediately.
● Select 
Scan after prompting me for settings  to specify additional settings before you
begin scanning.
● Select 
Set up the device  to program the Scan...

Program the all-in-one Scan To button
NOTEThe Scan To  button must be programmed before you can use it. However, some
destinations are programmed by default if the  all-in-one is directly connected to the computer.
To program the Scan To button
1.In the Hewlett-Packard program group, select  Scan to start HP LaserJet Scan.
NOTE Pressing  Start Scan  on the all-in-one control panel also starts HP LaserJet Scan
when the all-in-one is directly connected to the computer.
2. Click  Setup  to open the  Scan To...

Scan to e-mail
Scanning to e-mail is supported by Microsoft Outlook, Outlook Express, and Lotus Notes.
NOTETo use this feature in Windows, an e-mail recipient must be programmed in the  Scan
to  tab. See 
Programming the all-in-one Scan To button . For Macintosh operating systems, set
up this function from the  Monitor Device tab. See the HP Director online Help.
1.Load the originals that are to be scanned face-up in the automatic document feeder (ADF) input
tray. Adjust the media guides to hold the...

Network: How do I?
Use this section to answer network questions.
Set up the all-in-one and use it on the network
Hewlett-Packard recommends that you use the HP software installer on the CDs that came with the
all-in-one to set up printer drivers for the following network setups.
To configure a network port-connected all-in-one configuration (direct mode
or peer-to-peer printing)
In this configuration, the all-in-one is connected directly to the network, and all computers on the
network print directly to...

To configure a direct-connected shared all-in-one (client server printing)
In this configuration, the all-in-one is connected to a computer through a USB cable, the computer is
connected to the network, and the all-in-one is  shared with other computers on the network.
1. Insert the all-in-one CD into your computer. If  you have already set up your all-in-one, click
Install Software  to start the software installer. If the software installer does not start, navigate to
the hpsetup.exe file on the CD and...

To change from a direct-connected shared all-in-one to a network port-
connected all-in-one configuration
To change from a direct connection to a network configuration, complete the following steps.
1. Uninstall the printer driver for the direct connect all-in-one.
2. Install the driver as a network configuration by using the steps in 
To configure a network port-
connected all-in-one configuration (direct mode or peer-to-peer printing) .
Set my network password
Use HP ToolboxFX to set a network...

Other: How do I?
Use this section to answer other questions about the all-in-one.
Clean the paper path
During the printing process, paper, toner and dust particles can accumulate inside the all-in-one.
Over time, this buildup can cause print-quality problems such as toner specks or smearing. This all-
in-one has a cleaning mode that can correct and prevent these types of problems.
To clean the paper path from HP ToolboxFX
Use HP ToolboxFX to clean the paper path. This  is the recommended cleaning method....

To clean the paper path from the all-in-one control panel
If you do not have access to HP ToolboxFX, you can print and use a cleaning page from the all-in-
one control panel.
1.Press  Menu.
2. Use the  < or the  > button to find the  Service menu.
3. Press 
.
4. Use the  < or the  > button to find  Cleaning Mode .
5. Press 
.
6. Load plain letter or A4 paper when you are prompted.
7. Press 
 again to confirm and begin the cleaning process.
A page feeds through the all-in-one slowly. Discard the page when...

Use the Embedded Web server (EWS)
The EWS is a Web-based interface that provides simple access to all-in-one status and
configurations, including network configurations and Smart Printing Supplies (SPS) functionality.
You can gain access to the EWS through the network connection to the all-in-one. Type the all-in-
one IP address in a Web browser to open the all-in-one EWS homepage in the browser. From the
homepage, you can use the tabs and left navigation menu to check the status of the all-in-one,\...