HP LaserJet 3050z User Manual

Clearing stapler jams
To reduce the risk of staple jams, make sure that you staple 20 or fewer pages of media (80 g/m2 or
20 lb) at a time.
To clear a staple jam from the convenience stapler
1. Turn off the HP LaserJet 3392 all-in-one,  and then open the stapler door.
NOTEOpening the stapler door disables the stapler.
2.Remove the staple cassette from the all-in-one.
3.Clear any loose staples from the stapler and from the staple cassette.
ENWW Clearing stapler jams 193
 

4.Replace the staple cassette.
5.Close the stapler door and then  turn on the HP LaserJet 3390/3392 all-in-one.
6.Insert media to test the convenience stapler. Repeat steps 1 through 6 if necessary.
194 Chapter 10   Convenience stapler (HP LaserJet 3392 all-in-one only) ENWW
 

11 How do I?
●Print: How do I?
●
Fax: How do I?
●
Copy: How do I?
●
Scan: How do I?
●
Network: How do I?
●
Other: How do I?
ENWW 195
 

Print: How do I?
Use this section to answer printing questions.
Change the all-in-one print settings, such as volume or print
quality, in HP ToolboxFX
To change the default print settings in HP ToolboxFX, complete the following steps.
NOTEThe changes that you make to the print settings in HP ToolboxFX apply to all future
print jobs.
1. Open HP ToolboxFX and click  Device Settings.
2. Click the  System Settings  tab.
3. On the  System Settings  tab, you can modify settings that appear on the following...

Print on both sides (Windows)
Automatic two-sided printing (duplexing) is available using the automatic duplexer on the
HP LaserJet 3390/3392 all-in-one. Manual duplexing is available on the HP LaserJet
3050/3052/3055/3390/3392 all-in-one. To duplex manually, print on both sides of a page by feeding
the page through the all-in-one twice.
NOTE In the printer driver,  Print on Both Sides (manually)  is available only when duplex
printing is not available or when duplex printing is not supported for the...

4.After one side has been printed, remove the remaining media from the input tray, and set it
aside until after you finish your manual duplexing job.
HP LaserJet 3050 HP LaserJet 3052/3055
5.Gather the printed pages, keep the printed  side facing down, and straighten the stack.
HP LaserJet 3050 HP LaserJet 3052/3055
6.Place the stack of media in the input tray again.  The printed side should be facing down with the
top edge feeding into the all-in-one first.
1
HP LaserJet 3050 HP LaserJet 3052/3055
7.On...

To print on both sides manually (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to accommodate the print job. If you are loading
special paper such as letterhead, load it  in one of the following ways:
● For tray 1, load the letterhead paper with the front side up, bottom-edge first.
● For all other trays, load letterhead paper with front side down, and the top edge at the back
of the tray.
CAUTION
Do not load paper that is heavier than 105 g/m2 (28 lb bond). Jamming could...

Print on both sides (Macintosh)
Automatic two-sided printing (duplexing) is available by using the automatic duplexer on the
HP LaserJet 3390/3392 all-in-one. Manual duplexing is available on the HP LaserJet
3050/3052/3055/3390/3392 all-in-one. To duplex manually, print on both sides of a page by feeding
the page through the all-in-one twice.
To print on both sides automatically (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to  accommodate the print job. If you are...

To print on both sides manually (HP LaserJet 3050/3052/3055 all-in-one)
1.In the software program, open the all-in-one properties (printer driver).
2. On the  Finishing  tab, select  Manually print on 2nd side .
3. Print the document.
4. After one side has been printed, remove the remaining media from the input tray, and set it
aside until after you finish your manual duplexing job.
HP LaserJet 3050 HP LaserJet 3052/3055
5.Gather the printed pages, keep the printed side facing down, and straighten the...

To print on both sides manually (HP LaserJet 3390/3392 all-in-one) (Macintosh)
1.Insert enough paper into one of the trays to  accommodate the print job. If you are loading
special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper 
with the front side up, bottom-edge first.
● For all other trays, load letterhead paper with front
 side down, and the top edge at the back
of the tray.
CAUTION Do not load paper that is heavier than 105 g/m2 (28 lb bond)....