HP LaserJet 3050z User Manual

9Networking
●Set up the all-in-one and use it on the network (HP LaserJet 3052/3055/3390/3392 all-in-one
only)
●
Using the embedded Web server or HP ToolboxFX
●
Setting a network password
●
Using the all-in-one control panel
●
Supported network protocols
●
TCP/IP configuration
●
Using DHCP
●
Using BOOTP
●
Configuring for LPD printing
●
TCP/IP
NOTE Configuring TCP/IP settings are complicated and should only be performed by
experienced network administrators. BOOTP will require a (PC, Unix, Linux, and so...

Set up the all-in-one and use it on the network
(HP LaserJet 3052/3055/3390/3392 all-in-one only)
Hewlett-Packard recommends that you use the HP software installer on the CDs that came with the
all-in-one to set up printer drivers for the following network setups.
NOTENetworking capabilities are not available for the HP LaserJet 3050 all-in-one.
HP LaserJet 3052/3055
HP LaserJet 3390/3392
Figure 9-1  Network port location
Configuring a network-port-connected all-in-one
To configure a network-port-conne...

10.On the  Destination Folder  screen, choose the destination folder, and then click  Next.
11. On the  Ready to Install  screen, click Next to begin installation.
NOTE If you want to change your settings, instead of clicking  Next, click  Back to return
to previous screens, and then change the settings.
12. On the  Connection Type screen, select  Through the network, and then click Next.
13. On the  Identify Printer  screen, identify the all-in-one either by searching or by specifying a
hardware or IP...

13.On the Windows taskbar, click  Start, click Settings, and then click  Printers.
● In Windows XP, click 
Start, click  Control Panel , and then double-click  Printers and Faxes.
14. In the dialog box, right-click the all-in-one, and then click  Sharing.
15. Select  Share this printer , type the all-in-one name if necessary, and then click  OK.
Changing from a direct-connected shared all-in-one to a network-
port-connected all-in-one
To change from a direct-connected shared all-in-one to a...

Using the embedded Web server or HP ToolboxFX
You can use the embedded Web server (EWS) or HP ToolboxFX to view or change your IP
configuration settings. To gain access to the embedded Web server, type the IP address for the all-in-
one in the address line of your Web browser.
You can view HP ToolboxFX when the all-in-one is directly connected to your computer or when it is
connected to the network. You must perform  a complete software installation to use HP ToolboxFX.
Open HP ToolboxFX in one of these...

Using the all-in-one control panel
The all-in-one allows you to set up an IP address automatically using BOOTP or DHCP. For more
information, see 
Default IP address configuration (AutoIP).
Network configuration page
The Network configuration page lists the current settings and properties of the all-in-one. To print the
Network configuration page from the all-in-one, complete the following steps.
1.On the control panel, press  Menu.
2. Use the  < or the  > button to select  Reports, and then press 
.
3....

Automatic configuration
To perform automatic configuration
1.On the control , press  Menu.
2. Use the  < or the  > button to select  Network config. , and then press 
.
3. Use the  < or the  > button to select  TCP/IP config, and then press 
.
4. Use the  < or the  > button to select  Automatic, and then press 
.
It may take several minutes before the automatic IP address is ready for use.
NOTE If you want to disable or enable specific automatic IP modes (such as BOOTP,
DHCP, or AutoIP), these settings...

Supported network protocols
The HP LaserJet 3052/3055/3390/3392 all-in-one supports the TCP/IP network protocol. It is the
most widely used and accepted networking protocol.  Many networking services utilize this protocol.
The following table lists the networking services/protocols  that are supported on the HP LaserJet
3052/3055/3390/3392 all-in-one.
The following operating systems support network printing:
● Windows 98 SE
● Windows Me
● Windows 2000
● Windows XP
Table 9-1
  Printing
Service...

Table 9-4  IP addressing
Service nameDescription
DHCP (dynamic host configuration protocol)For Automatic IP address assignment. DHCP server
provides the all-in-one with an IP address. Generally
requires no user intervention for all-in-one to obtain IP
address from a DHCP server.
BOOTP (bootstrap protocol)For Automatic IP address assignment. BOOTP server
provides the all-in-one with an IP address. Requires
administrator to input the all-in-one MAC hardware address
on BOOTP server in order for all-in-one...

TCP/IP configuration
To operate correctly on a TCP/IP network, the all-in-one must be configured with valid TCP/IP
network configuration parameters, such as an IP address that is valid for your network.
CAUTIONChanges to these settings might result in  a loss of functionality with your all-in-
one. For example, network scanning, network faxing, or HP Web JetAdmin might stop working
with certain settings changes.
Server-based, AutoIP, and manual TCP/IP configuration
When in a factory-default state and...