HP LaserJet 3050 User Manual

							5.Gather the printed pages, keep the printed side facing down, and straighten the stack.
HP LaserJet 3050 HP LaserJet 3052/3055
6.Place the stack of media in the input tray again. The printed side should be facing down with the
top edge feeding into the all-in-one first.
1
HP LaserJet 3050 HP LaserJet 3052/3055
7.On the computer screen, click  OK and wait for the second side to print.
ENWW Using features in the Windows printer driver 53
 
						

							To print on both sides manually (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to  accommodate the print job. If you are loading
special paper such as letterhead, load it in one of the following ways:
● For tray 1, load the letterhead paper 
with the front side up, bottom-edge first.
● For all other trays, load letterhead paper with front
 side down, and the top edge at the back
of the tray.
CAUTION Do not load paper that is heavier than 105 g/m2 (28 lb bond). Jamming could
result.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. On the  Finishing  tab, select  Print on Both Sides (manually) .
4. Click  OK.
5. Send the print job to the product.
6. Go to the all-in-one. Remove any blank paper that is in tray 1.  Insert the printed stack into the
tray that is specified on the control panel.  Load the paper with the printed side up, and the
bottom-edge feeding into the all-in-one first. Follow the instructions in the pop-up window that
appears before feeding the output stack back for  printing the second half of the job.
7. A prompt might appear on the control-panel display that instructs you to press a button to
continue.
54 Chapter 5   Printing ENWW
 
						

							Using features in the Macintosh printer driver
When you print from a software program, many of the features are available from the printer driver.
For complete information about the features that are available in the printer driver, see the printer-
driver Help. The following features are described in this section:
●
Creating and using presets in Mac OS X V10.3 and Mac OS X V10.4
●
Printing a cover page (Macintosh)
●
Printing multiple pages on one sheet of paper (Macintosh)
●
Printing on both sides (Macintosh)
NOTE Settings in the printer driver and software program generally override control-panel
settings. Software-program settings generally override printer-driver settings.
Creating and using presets in Mac OS  X V10.3 and Mac OS X V10.4
Use presets to save the current driver settings for  reuse. For example, you can save the page
orientation, print-on-both-sides feature, and paper-type settings in a preset.
To create a preset
1. Open the printer driver (see 
Gaining access to the printer drivers ).
2. Select the print settings that you want to use.
3. In the  Presets  box, click  Save As... , and type a name for the preset (for example Quarterly
Report or My Project Status).
4. Click  OK.
To use presets
1. Open the printer driver (see 
Gaining access to the printer drivers ).
2. In the  Presets  menu, select the preset that you want to use.
NOTE To restore printer-driver default settings, select  Standard from the Presets pop-up
menu.
ENWW Using features in the Macintosh printer driver 55
 
						

							Printing a cover page (Macintosh)
If you want to, you can print a separate cover page for your document that includes a message (such
as “Confidential”).
To print a cover page
1.Open the printer driver (see 
Gaining access to the printer drivers ).
2. On the  Cover Page  pop-up menu, select whether to print the cover page  Before Document or
After Document.
3. If you are using Mac OS X V10.3  or Mac OS X V10.4, in the Cover Page Type pop-up menu,
select the message that you want to print on the cover page.
NOTE To print a blank cover page, select  Standard as the Cover Page Type .
Printing multiple pages on one sheet of paper (Macintosh)
You can print more than one page on a single sheet of paper. This feature provides a cost-effective
way to print draft pages.
To print multiple pages on one sheet of paper
1.Open the printer driver (see 
Gaining access to the printer drivers ).
2. Click the  Layout pop-up menu.
3. Next to  Pages per Sheet , select the number of pages that you want to print on each sheet (1,
2, 4, 6, 9, or 16).
4. If the number of pages is greater than 1, next to  Layout Direction, select the order and
placement of the pages on the sheet.
5. Next to  Borders , select the type of border to print around each page on the sheet.
56 Chapter 5   Printing ENWW
 
						

							Printing on both sides (Macintosh)
Automatic two-sided printing (duplexing) is available by using the automatic duplexer on the
HP LaserJet 3390/3392 all-in-one. Manual duplexing is available on the HP LaserJet
3050/3052/3055/3390/3392 all-in-one. To duplex manually, print on both sides of a page by feeding
the page through the all-in-one twice.
To print on both sides automatically (HP LaserJet 3390/3392 all-in-one)
1.Insert enough paper into one of the trays to accommodate the print job. If you are loading
special paper such as letterhead, load it  in one of the following ways:
● For tray 1, load the letterhead paper with 
the front side up and the bottom-edge feeding
into the all-in-one first.
● For all other trays, load the letterhead paper with
 the front side down and the top edge at
the back of the tray.
CAUTION Do not load paper that is heavier than 105 g/m2 (28-lb bond). Jamming might
result.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. Open the  Layout pop-up menu.
4. Next to  Two Sided Printing , select either Long-Edge Binding  or Short-Edge Binding .
5. Click  Print.
To print on both sides manually (HP LaserJet 3050/3052/3055 all-in-one)
1.On the  Print dialog, select  Printer Features.
2. On the  Feature Sets  list, select Finishing, and then select  Manually print on 2nd side .
3. Print the document.
4. After one side has been printed, remove the remaining media from the input tray, and set it
aside until after you finish your manual duplexing job.
HP LaserJet 3050 HP LaserJet 3052/3055
ENWWUsing features in the Macintosh printer driver 57
 
						

							5.Gather the printed pages, keep the printed  side facing down, and straighten the stack.
HP LaserJet 3050 HP LaserJet 3052/3055
6.Place the stack of media in the input tray again.  The printed side should be facing down with the
top edge feeding into the all-in-one first.
1
HP LaserJet 3050 HP LaserJet 3052/3055
7.On the computer screen, click  OK and wait for the second side to print.
58 Chapter 5   Printing ENWW
 
						

							To print on both sides manually (HP LaserJet 3390/3392 all-in-one) (Macintosh)
1.Insert enough paper into one of the trays to accommodate the print job. If you are loading
special paper such as letterhead, load it  in one of the following ways:
● For tray 1, load the letterhead paper with the front side up, bottom-edge first.
● For all other trays, load letterhead paper with front side down, and the top edge at the back
of the tray.
CAUTION
Do not load paper that is heavier than 105 g/m2 (28 lb bond). Jamming could
result.
2. Open the printer driver (see Gaining access to the printer drivers ).
3. On the  Finishing  tab, select  Print on Both Sides (manually) .
4. Click  OK.
5. Send the print job to the product.
6. Go to the all-in-one. Remove any blank paper that is in tray 1.  Insert the printed stack into the
tray that is specified on the control panel.  Load the paper with the printed side up, and the
bottom-edge feeding into the all-in-one first. Follow the instructions in the pop-up window that
appears before feeding the output stack back for  printing the second half of the job.
7. A prompt might appear on the control-panel display that instructs you to press a button to
continue.
ENWW Using features in the Macintosh printer driver 59
 
						

							Selecting an output location (HP LaserJet 3390/3392 all-
in-one)
The HP LaserJet 3390/3392 all-in-one comes with the top output bin and a rear output door for
printing to a straight-through output path. Print jobs emerge  from the top output bin when the rear
output door is closed. Print jobs emerge from the back  of the all-in-one when the rear output door is
open.
● Open the rear output door to use the straight-through output path if problems occur when
printing to the top output bin, or when printing
 on such media as card stock, envelopes, labels,
or photo paper. Remove each sheet as it exits the all-in-one.
● Use the top output bin when printing most jobs, including jobs on average-weight paper,
letterhead, and transparencies. The top output bin can hold up to 125 sheets. Prevent more
than 125 sheets from accumulating in the 
top output bin, or jams can occur.
21
1Rear output door
2Top output bin
60 Chapter 5   Printing ENWW
 
						

							Printing on special media
Use these guidelines when printing on special types of media.
NOTENot all features are available for all printer drivers or operating systems. See the all-in-
one properties (driver) online Help for information  about the available features for the driver.
Printing on special media (HP LaserJet 3050/3052/3055 all-in-one)
1.Open the media input tray and remove any media.
2.Load the media. Make sure that the top of the media  is forward and the side to be printed on is
facing up.
3. Adjust the media guides to the  length and width of the media.
4.For Windows printer drivers, on the  Paper tab or the  Paper/Quality  tab, select your media type
from the  Type is: drop-down list.
For Macintosh printer drivers, on the  Paper/Quality tab or the Paper  tab (the Paper Type/
Quality  tab for some Macintosh  drivers), select your media type.
5. Print the document.
ENWW Printing on special media 61
 
						

							Printing on special media (HP LaserJet 3390/3392 all-in-one)
1.Open the rear output door.
2.Before feeding the media, open the single-sheet priority  input slot (tray 1), and adjust the media
guides to the width of the media.
3. Feed a single page into the single-sheet priority input slot  (tray 1). Make sure that the top of the
media is forward and the side to be printed (rough side) is facing up. The media feeds partially
into the all-in-one, and then the all-in-one pauses.
4. For Windows printer drivers, open the all-in-one  Properties (or Printing Preferences  in
Windows 2000 and XP). See 
Gaining access to the printer drivers  for instructions.
For Macintosh drivers, on the  Paper/Quality tab or the Paper tab (the  Printer Features  tab for
some Mac drivers), choose the correct media type.
5. Print the document. Remove the media from the back  of the all-in-one as it prints to prevent it
from sticking together, and place the printed pages on a flat surface.
62 Chapter 5   Printing ENWW