HP LaserJet 2430tn User Manual

Service menu
The Service menu is locked and requires a PIN for access. This menu is intended for use by
authorized service personnel.
ENWW Service menu179
 

180Appendix B Control panel menus  ENWW
 

C
Specifications
HP LaserJet 2400 series physical specifications
Product dimensions
ProductHeightDepthWidthWeight1
HP LaserJet 2410, 2420,
2420d, 2420n, 2420dn, and
2430n260 mm
(10.2 inches)400 mm
(15.7 inches)425 mm
(16.7 inches)15.2 kg
(33.5 lb)
HP LaserJet 2430t, 2430tn,
and 2430dtn400 mm
(15.7 inches)400 mm
(15.7 inches)425 mm
(16.7 inches)20.9 kg (46 lb)
optional 500-sheet feeder140 mm
(5.5 inches)400 mm
(15.7 inches)425 mm
(15.7 inches)5.7 kg (12.5 lb)
1Without print cartridge
Product dimensions,...

Electrical specifications
WARNING!Power requirements are based on the country/region where the printer is sold. Do not
convert operating voltages. This can damage the printer and void the product warranty.
Power requirements (HP LaserJet 2400 series)
Specification110-volt models230-volt models
Power requirements110 to 127 volts (± 10%)
50/60 Hz (± 2 Hz)220 to 240 volts (± 10%)
50/60 Hz (± 2 Hz)
Rated short-term current10.0 Amps5.0 Amps
Power consumption HP LaserJet 2400 series (average, in watts)1...

Acoustic emissions
Sound power and pressure level1 (HP LaserJet 2400 series)
Sound power levelDeclared per ISO 9296
Printing2 (HP LaserJet 2410)LWAd= 6.6 Bels (A) [66 dB(A)]
Printing2 (HP LaserJet 2420)LWAd= 6.7 Bels (A) [67 dB(A)]
Printing2 (HP LaserJet 2430)LWAd= 6.8 Bels (A) [68 dB(A)]
Ready (HP LaserJet 2410)Essentially Inaudible
Ready (HP LaserJet 2420)Essentially Inaudible
Ready (HP LaserJet 2430)Essentially Inaudible
Sound pressure levelDeclared per ISO 9296
Printing2 (HP LaserJet 2410)LpAm=52 dB...

Operating environment
Environmental condition PrintingStorage/standby
Temperature (printer and print
cartridge)15° to 32.5°C (59° to 89°F)-20° to 40°C (-4° to 104°F)
Relative humidity10% to 80%10% to 90%
184Appendix C Specifications ENWW
 

Paper specifications
For complete paper specifications for all HP LaserJet printers, see the HP LaserJet printer
family print media guide  (available at http://www.hp.com/support/ljpaperguide ).
CategorySpecifications
Acid content5.5 pH to 8.0 pH
Caliper0.094 to 0.18 mm (3.0 to 7.0 mils)
Curl in reamFlat within 5 mm (0.02 inch)
Cut edge conditionsCut with sharp blades with no visible fray.
Fusing compatibilityMust not scorch, melt, offset, or release
hazardous emissions when heated to 200°C
(392°F) for...

The paper storage environment should be properly maintained to ensure optimum printer
performance. The required condition is 20° to 24°C (68° to 75°F), with a relative humidity of
45% to 55%. The following guidelines should be  helpful when evaluating the papers storage
environment:
● Paper should be stored at or near room temperature.
● The air should not be too dry or too  humid (due to the hygroscopic properties of paper).
● The best way to store an opened ream of  paper is to rewrap it tightly in its...

Envelopes with double side seams
Double side-seam construction has vertical seams at both ends of the envelope rather than
diagonal seams. This style might be more likely to wrinkle. Be sure the seam extends all the
way to the corner of the envelope as illustrated below.
1
2
1 Acceptable envelope construction
2 Unacceptable envelope construction
Envelopes with adhesive strips or flaps
Envelopes with a peel-off adhesive strip or with more  than one flap that folds over to seal
must use adhesives...

Labels
CAUTIONTo avoid damaging the printer, use only labels recommended for laser printers. To prevent
serious jams, always use tray 1 to print labels and always use the rear output bin. Never
print on the same sheet of labels more than  once or print on a partial sheet of labels.
Label construction
When selecting labels, consider the quality of each component:
●Adhesives:  The adhesive material should be stable at 200°C (392°F), the printers
fusing temperature.
● Arrangement:  Only use labels with no...