HP Deskjet D1560 User Manual

							To resolve the problem, follow the instructions in Resolving print cartridge error
messages.
Print cartridge problem message
The printer cannot print if the print cartridges are faulty, or if they are not installed properly.
If you receive a message stating there is a problem with a print cartridge, follow the
instructions in 
Resolving print cartridge error messages to resolve the problem.
Print cartridge carriage is stuck
If the printer stalls while you are printing a document, follow the instructions in 
Print
cartridge carriage is stalled.
Print cartridge is in the wrong slot
Solution:Always install the tri-color print cartridge in the left print cartridge carriage
compartment.
Install the black print cartridge in the right print cartridge carriage compartment.
Cause:If you received this error message, the print cartridge was installed in the
wrong side of the print cartridge carriage.
Non-HP print cartridges
Solution:Follow the prompts on the computer screen to continue or replace the
indicated print cartridges. For more information, see 
Replace print cartridges.
HP recommends that you use genuine HP print cartridges. Genuine HP print
cartridges are designed and tested with HP printers to help you easily produce great
results, time after time.
NOTE:HP cannot guarantee the quality or reliability of non-HP supplies. Printer
service or repairs required as a result of using a non-HP supply will not be covered
under warranty.
If you believe you purchased genuine HP print cartridges, go to:
www.hp.com/go/anticounterfeit
Cause:The product detected that a non-HP print cartridge was installed.
Incompatible print cartridges
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
•
Solution 1: Make sure you are using the correct print cartridges
•
Solution 2: Contact HP customer support
Chapter 11
58 Troubleshooting
Troubleshooting
 
						

							Solution 1: Make sure you are using the correct print cartridges
Solution:Check to make sure you are using the correct print cartridges for your
product. For a list of compatible print cartridges, see the printed documentation that
came with the product.
If you are using print cartridges that are not compatible with the product, replace the
indicated print cartridges with print cartridges that are compatible.
If it appears that you are using the correct print cartridges, proceed to the next
solution.
For more information, see:
•
Shop for ink supplies
•
Replace print cartridges
Cause:The indicated print cartridges were not compatible with the product.
Solution 2: Contact HP customer support
Solution:To find support and warranty information, go to the HP Web site at
www.hp.com/support. If prompted, choose your country/region, and then click
Contact HP for information on calling for technical support.
Cause:The print cartridges were not intended for use in this product.
Previously used genuine HP cartridge
Solution:Check the print quality of the current print job. If it is satisfactory, follow
the prompts on the computer screen to continue.
Ink levels might not be available for the indicated print cartridges. Ink level warnings
and indicators provide estimates for planning purposes only. When you receive a low-
ink warning message, consider having a replacement cartridge available to avoid
possible printing delays. You do not need to replace the print cartridges until print
quality becomes unacceptable.
Cause:A genuine HP print cartridge was previously used in another printer.
Original HP ink depleted
Solution:Follow the prompts on the computer screen to continue or replace the
indicated print cartridges. For more information, see 
Replace print cartridges.
Ink levels might not be available for the indicated print cartridges. Ink level warnings
and indicators provide estimates for planning purposes only. When you receive a low-
ink warning message, consider having a replacement cartridge available to avoid
possible printing delays. You do not need to replace the print cartridges until print
quality becomes unacceptable.
HP recommends that you use genuine HP print cartridges. Genuine HP print
cartridges are designed and tested with HP printers to help you easily produce great
results, time after time.
Error messages 59
Troubleshooting
 
						

							NOTE:HP cannot guarantee the quality or reliability of non-HP supplies. Printer
service or repairs required as a result of using a non-HP supply will not be covered
under warranty.
If you believe you purchased genuine HP print cartridges, go to:
www.hp.com/go/anticounterfeit
Cause:The original HP ink in the indicated print cartridges has been depleted.
Low on ink
Solution:Ink level warnings and indicators provide estimates for planning purposes
only. When you receive a low-ink warning message, consider having a replacement
cartridge available to avoid possible printing delays. You do not need to replace the
print cartridges until print quality becomes unacceptable. If you have installed a refilled
or remanufactured print cartridge, or a cartridge that has been used in another printer,
the ink level indicator may be inaccurate or unavailable.
For more information on replacing print cartridges, see 
Replace print cartridges.
Cause:At least one of the print cartridges is estimated to be low on ink and may
need to be replaced soon.
Printing in ink-backup mode
Solution:If you receive the ink-backup mode message and two print cartridges are
installed in the printer, verify that the protective piece of plastic tape has been
Chapter 11
60 Troubleshooting
Troubleshooting
 
						

							removed from each print cartridge. When plastic tape covers the print cartridge
contacts, the printer cannot detect that the print cartridge is installed.
To remove plastic tape from a print cartridge
▲Hold the print cartridge so that the copper strips are on the bottom and facing
toward the printer, and then carefully remove the plastic tape.
1Remove plastic tape
CAUTION:Do not touch the print cartridge ink nozzles or copper contacts.
Touching these parts will result in clogs, ink failure, and bad electrical
connections. Do not remove the copper strips. They are required electrical
contacts.
Cause:When the printer detects that only one print cartridge is installed, ink-backup
mode is initiated. This printing mode lets you print with a single print cartridge, but it
slows the printer and affects the quality of printouts.
Paper Mismatch or Paper Size message
Solution:In Microsoft Word, prior to printing envelopes, set the paper size to #10
envelope on the Features tab of the Printer Preferences dialog box.
NOTE:Do not set the paper size from the Printers folder or from the printer icon
located in the lower-right hand corner of the screen next to the clock, because this
will affect all applications. Only set the paper size in Microsoft Word.
To set the paper size in Microsoft Word
1.In Microsoft Word, click File, and then click Print.
2.Make sure that the appropriate printer is selected, and then click Properties.
3.Click the Features tab.
4.In the Size drop-down list, select Envelope #10.
5.Click OK on the Printer Properties dialog box.
Error messages 61
Troubleshooting
 
						

							6.Click Cancel on the Print dialog box.
7.Print the envelope using the Envelopes and Labels feature in Microsoft Word. The
envelope should print without any errors.
NOTE:When you are finished printing envelopes, set the paper size back to
the default print settings.
Out of paper
If you receive an out of paper message, follow the guidelines in Out of paper.
There was an error writing to USB port
The printer might not be receiving correct data from another USB device or USB hub.
Connect the printer directly to the USB port on the computer.
Two-way communication cannot be established or Printer not responding
The printer might not be able to communicate with the computer if the USB cable is too
long.
If you receive this error message, make sure that the USB cable is not greater than 3
meters (approximately 9.8 feet) in length.
NOTE:For best printing performance, use a USB 2.0 compatible cable.
Installation problems
If the software installation program stops or fails, check the following topics for more
information:
•
Installation program stops
•
Unknown Device message displays
•
Printer name does not appear
If you continue to have problems, visit HP Technical Support at 
www.hp.com/support.
Installation program stops
Cause:If the installation program stops when it looks for new hardware, one of the
following issues is causing a communication problem:
• The USB cable is old or defective.
• Software, such as an antivirus program, is running.
• Another device, such as a scanner, is connected to the computer.
Chapter 11
62 Troubleshooting
Troubleshooting
 
						

							Solution:
To resolve the problem
1.Make sure that no USB devices other than the printer, the keyboard, and the
mouse are connected to the computer.
2.Disconnect and reconnect the USB cable.
3.Make sure that the printer is connected directly to a USB port on the computer
(instead of through a USB hub).
4.If the installation program still does not locate the printer, replace the USB cable,
and then continue to the next step.
5.Click Cancel, and then restart the computer.
6.Turn the printer off, and then disconnect the USB cable and power cord.
7.Quit any antivirus programs or other software programs that are running on the
computer.
NOTE:To quit an antivirus program, follow the manufacturer’s instructions.
8.Reinstall the printer software:
a. Insert the printer software CD into the drive.
b. Follow the onscreen instructions. When the installation program prompts you,
connect the USB cable and the power cord to the printer, and then make sure
that the printer is on.
NOTE:Do not connect the USB cable until you are told to do so.
c. Follow the onscreen instructions to finish the installation.
9.Restart the antivirus program.
Unknown Device message displays
Cause:During installation, an “Unknown Device” message might be displayed
when you connect a USB cable between the printer and the computer. A possible
cause might be a defective USB cable.
Solution:
NOTE:This is not a problem if you are using Windows 2000. If you are using
Windows 2000 and this message is displayed, you can continue with the software
installation.
To resolve the problem
1.Disconnect the USB cable from the printer.
2.Disconnect the power cord from the printer.
3.Wait approximately 30 seconds.
4.Reconnect the power cord to the printer.
5.Reconnect the USB cable to the printer.
6.If the “Unknown Device” message is still displayed, replace the USB cable.
Installation problems 63
Troubleshooting
 
						

							Printer name does not appear
Solution:If the printer software seems to install correctly, but the printer name does
not appear in the list of printers when you click Print on the File menu or in the Printers
folder in Control Panel, try reinstalling the printer software.
To reinstall the printer software
1.Quit any antivirus programs or other software programs that are running on the
computer.
NOTE:To quit an antivirus program, follow the manufacturer’s instructions.
2.Uninstall the printer software:
a. Insert the printer software CD into the drive, and then follow the onscreen
instructions.
NOTE:If the installation program does not start automatically, click your
CD drive letter in Windows Explorer, then double-click the setup.exe file.
For example, double-click D:\setup.exe.
b. When prompted, click Remove All.
3.Reinstall the printer software:
a. Insert the printer software CD into the drive.
b. Follow the onscreen instructions to finish the installation.
4.Restart the antivirus program.
Power light is on or flashing
1Power light
If the Power light is on, the printer is either printing or ready to print.
If the Power light is off, the printer is off.
If the Power light is flashing, see the following information:
•
What the flashing light means
•
If an error message appears
•
If no error message appears
Chapter 11
64 Troubleshooting
Troubleshooting
 
						

							What the flashing light means
The Power light can flash for several reasons:
• The printer cover is open.
• The printer is out of paper.
• A problem exists with the printer, such as a paper jam or a problem with a print
cartridge.
For information about clearing a paper jam, see 
Paper jam.
If an error message appears
Read the error message that explains the problem and its solution.
If no error message appears
Check the status of the printer by using the printer tools. To gain access to the tools, open
the 
Printer Properties dialog box, click the Features tab, and then click the Printer
services button.
Use the printer tools to perform the following tasks:
• View estimated ink levels.
• Clean the print cartridges.
• Calibrate the printer.
• Print a test page.
• Perform other functions as needed.
Printer does not print
•Verify the following
•
Unable to print
•
If the printer still does not print
Verify the following
Verify the following conditions if the printer is not printing:
• The printer is connected to the power source.
• The cable connections are secure.
• The printer is turned on.
• The print cartridges are the correct print cartridges for the printer and are properly
installed.
For more information, see 
Print cartridges and Installation instructions.
• The paper or other media is correctly loaded in the paper tray.
• The printer cover is closed.
• The rear access door is attached.
Printer does not print 65
Troubleshooting
 
						

							Unable to print
Try the following solutions:
•
Solution 1: Make sure the printer is turned on
•
Solution 2: Print a test page
•
Solution 3: Clear the print queue
•
Solution 4: Check the printer cable connection
•
Solution 5: Verify the printer driver configuration
•
Solution 6: Check if the printer is paused or offline
•
Solution 7: Clear the print queue manually
•
Solution 8: Restart the print spooler
•
Solution 9: Verify whether the software application is causing the problem
Solution 1: Make sure the printer is turned on
Solution:Look at the Power light located on the front of the printer. If it is not lit, the
printer is turned off. Make sure the power cord is firmly connected to the printer and
plugged into a power outlet. Press the Power button to turn on the printer.
Cause:The product was turned off.
If this did not solve the issue, try the next solution.
Solution 2: Print a test page
Solution:Print a test page to see if the product can print and is communicating with
the computer.
To print a test page
1.Load Letter or A4 unused plain white paper in the paper tray.
2.Open the printer 
Toolbox.
3.On the Device Services tab, click the Print a Test Page button.
The Print a Test Page dialog box is displayed.
4.Click the Print Page button.
Recycle or discard the test page.
If the test page fails to print, make sure you set up the product properly. See the Setup
Guide that came with the product for information about setting it up.
Cause:The product was not set up properly.
If this did not solve the issue, try the next solution.
Chapter 11
66 Troubleshooting
Troubleshooting
 
						

							Solution 3: Clear the print queue
Solution:Restart your computer to clear the print queue.
To clear the print queue
1.Restart your computer.
2.After the computer has restarted, check the print queue.
a. Depending upon your operating system, do one of the following:
• Windows Vista: On the Windows taskbar, click Start, click Control
Panel, and then click Printers.
• Windows XP: On the Windows taskbar, click Start, click Control Panel,
and then click Printers and Faxes.
• Windows 2000: On the Windows taskbar, click Start, point to Settings,
and then click Printers.
b. Double-click the icon for your product to open the print queue.
If there are no print jobs pending, the issue might have been resolved.
3.Try to print again.
Cause:The computer needed to be restarted to clear the print queue.
If this did not solve the issue, try the next solution.
Solution 4: Check the printer cable connection
Solution:Disconnect the USB cable from the computer and product, and then
reconnect it.
To disconnect and reconnect the USB cable
1.Disconnect the USB cable from the product.
2.Disconnect the USB cable from the computer.
3.Leave the USB cable disconnect for 5-6 seconds.
4.Reconnect the USB cable to the product and the computer.
After reconnecting the USB cable, the product should start printing the jobs in
queue.
NOTE:If you are connecting the product through a USB hub, make sure the
hub is turned on. If the hub is on, try connecting directly to your computer.
5.If the product does not start printing automatically, start another print job.
Cause:The USB cable needed to be disconnected.
If this did not solve the issue, try the next solution.
Printer does not print 67
Troubleshooting