HP Designjet Z3200 24 in User Manual

8.Lower the handle to rest on the carriage lid.
When all the printheads have been inserted correctly and are accepted by the printer, the printer
beeps.
NOTE:If the printer does not beep when you insert the printhead and the Replace message
appears on the front-panel display, the printhead may need to be reinserted.
9.Close the window.
10.The front-panel display confirms that all printheads are correctly inserted. The printer starts
checking and preparing the printheads. The default routine process, when...

9 Maintaining the printer
●Check printer status
●
Clean the exterior of the printer
●
Replace the cutter
●
Maintain the ink cartridges
●
Move or store the printer
●
Update the firmware
●
Update the software
●
Change the battery
●
Printer maintenance kits
●
Secure Disk Erase
92 Chapter 9   Maintaining the printer ENWW
Printer maintenance
 

Check printer status
You can check the current status of the printer in various ways:
●If you start the HP Printer Utility and select your printer, you see a page of information describing
the status of the printer and its paper and ink supplies.
●If you access the Embedded Web Server, you see information about the general status of the
printer. The Supplies page in the Main tab describes the status of the paper and ink supplies.
●The status screen of the printers front panel notifies you of any current...

4.Lift the ink cartridge cover on the left-hand side of the printer.
5.Press the button behind the ink cartridges to release the cover of the left-hand end of the printer.
6.Remove the left end cover.
94 Chapter 9   Maintaining the printer ENWW
Printer maintenance
 

7.Unscrew and remove the cutter stop using the TORX PLUS screwdriver provided with the new
cutter. The screw is captive and will not fall out.
8.Remove the old cutter.
9.Take the new cutter from the maintenance kit and move the plunger at the top slowly back and
forth within its housing to check that it moves freely.
ENWWReplace the cutter 95
Printer maintenance
 

10.Slide the new cutter into position on the cutter rail.
The two wheels on the bottom of the cutter should engage the central ridge on the cutter rail, and
the two bushing guides should fit into the groove in the upper part of the cutter rail.
Check that the cutter runs smoothly up and down the rail. You can leave it anywhere on the rail;
the printer will park it correctly later.
11.Fit the cutter stop onto the end of the cutter rail, holding it there with one hand while you tighten
the screw with the...

12.Put the left end cover back on the printer, aligning the protrusions with the holes in the printer.
13.Close the ink cartridge cover.
14.At the front panel, turn the printer back on. The printer checks that the cutter has been correctly
installed. Look at the front panel and follow its instructions if there is any problem.
Maintain the ink cartridges
During the normal lifetime of a cartridge, no specific maintenance is required. However, in order to
maintain the best print quality, replace a cartridge...

5.Before transporting the printer, secure the rear tray in the closed position with tape. Otherwise, the
tray could open and perhaps break and fall out of the printer.
If you need to leave the printer turned off for a long time, follow the additional steps below.
1.Turn off the power using the Power key on the front panel.
2.Also turn off the power switch at the rear of the printer.
3.Disconnect the printers power cable.
CAUTION:If you turn the printer upside down, ink could escape into the printer and...

If you experience very slow progress while uploading the firmware file to the printer, the reason could
be that you are using a proxy server. In that case, try bypassing the proxy server and accessing the
Embedded Web Server directly.
●In Internet Explorer 6 for Windows, go to Tools > Internet Options > Connections > LAN
Settings, and check the Bypass proxy server for local addresses box. Alternatively, for more
precise control, click the Advanced button and add the printers IP address to the list of...

Secure Disk Erase provides three different levels of security:
●Non-Secure Fast Erase: all pointers to the information are erased. The information itself remains
on the hard disk until the disk space it occupies is needed for other purposes, and it is then
overwritten. While it remains on the disk, it is difficult for most people to access, but may be
accessed using software designed for the purpose. This is the normal method in which files are
erased on most computer systems; it is the fastest method...