HP Designjet Z3200 24 in User Manual

8 Handling ink cartridges and printheads
●About the ink cartridges
●
Check ink cartridge status
●
Remove an ink cartridge
●
Insert an ink cartridge
●
About the printheads
●
Check printhead status
●
Remove a printhead
●
Insert a printhead
ENWW81
Ink and printheads
 

About the ink cartridges
Ink cartridges store the ink and are connected to the printheads, which distribute the ink on the paper.
You can purchase 130 ml ink cartridges for your printer, see 
Accessories on page 101.
CAUTION:Observe precautions when handling ink cartridges because they are ESD-sensitive
devices (see the 
Glossary on page 160). Avoid touching pins, leads and circuitry.
Check ink cartridge status
To view the ink levels of your ink cartridges, press the View ink level key on the front...

CAUTION:Make sure the printer wheels are locked (the brake lever is pressed down) to prevent the
printer from moving.
1.
From the front panel, select the Ink menu icon 
, then Replace ink cartridges.
2.Open the ink cartridge cover completely. Gloss enhancer, gray, blue, green, magenta and yellow
are in the left side, while light magenta, light cyan, photo black, light gray, matte black and red are
in the right side.
3.Grip the cartridge you wish to remove.
ENWWRemove an ink cartridge 83
Ink and printheads
 

4.Pull the cartridge straight up.
NOTE:Avoid touching the end of the cartridge that is inserted into the printer, as there may be
ink on the connection.
NOTE:Avoid storing partially used ink cartridges.
5.The front-panel display identifies the missing ink cartridge.
Insert an ink cartridge
1.Before removing the cartridge from its wrapping, shake it vigorously.
2.Unwrap the new ink cartridge, find the label identifying the ink color. Check that the letter or letters
(in these illustrations, M for magenta)...

3.Insert the ink cartridge into its slot.
4.Push the cartridge into the slot until it snaps into position. You should hear a beep and see
confirmation that the cartridge has been inserted.
If you have difficulty, see Cannot insert an ink cartridge on page 138.
5.When all cartridges have been inserted, close the cover.
6.The front-panel display confirms that all cartridges have been correctly inserted, press the OK key
on the front panel.
About the printheads
The printhead are connected to the ink...

CAUTION:Observe precautions when handling printheads because they are ESD-sensitive devices
(see the 
Glossary on page 160). Avoid touching pins, leads and circuitry.
Check printhead status
The printer automatically checks and services the printheads after each print. Follow the steps below
to get more information on your printheads.
1.
From the front panel, select the Ink menu icon 
, then Printhead information.
2.Select the printhead on which you want information.
3.The front panel displays information...

3.When the carriage has stopped moving, the front-panel display asks you to open the window.
4.Locate the carriage on the right side of the printer.
5.To Pull the handle up and toward you to release the wire loop.
6.Push the handle back to raise the carriage lid.
7.This gives you access to the printheads.
ENWWRemove a printhead 87
Ink and printheads
 

8.To remove a printhead, lift up the blue handle.
9.Using the blue handle, use steady force to disengage the printhead.
10.Pull the blue handle upward until the printhead is released from the carriage.
CAUTION:Do not pull abruptly because this can damage the printhead.
11.The front-panel display identifies the missing printhead.
Insert a printhead
1.If the printhead is new, shake the printhead vigorously before removing the protective caps.
88 Chapter 8   Handling ink cartridges and printheads ENWW
Ink...

2.Remove the orange protective caps by pulling them down.
3.The printhead is designed to prevent you from accidentally inserting it into the wrong slot. Check
that the colored label on the printhead matches the colored label of the carriage slot into which the
printhead is to be inserted.
4.Insert the new printhead into its correct slot in the carriage.
CAUTION:Insert the printhead slowly and vertically, straight down. It may be damaged if you
insert it too fast, or at an angle, or if you rotate it as...

5.Push down as indicated by the arrow shown below.
CAUTION:When installing the new printhead there may be some resistance, so you need to
press it down firmly but smoothly. You should hear a beep and see confirmation on the front-panel
display that the printhead has been inserted. If you have difficulty, see 
Cannot insert a printhead
on page 138.
6.Insert any other printheads, that need to be installed, with the same procedure, then close the
carriage lid.
7.Ensure the end of the blue handle catches the...