HP Designjet T1300 1118 mm User Manual

							●Ensure that the graphic language setting is correct, see Change the graphic language setting
on page 36.
●If the printer is connected by USB cable, try disconnecting and reconnecting the USB cable. Also
try using a different USB port on the computer.
Cannot access the HP Utility
If you have not done so already, please read Access the HP Utility on page 33.
From the front panel, press 
, then , then Setup > Connectivity > Advanced > Web
Services > Printer utility software > Enabled.
If you still cannot connect, switch the printer off and back on with the Power key on the front panel.
Cannot access the Embedded Web Server
If you have not done so already, please read Access the Embedded Web Server on page 33.
NOTE:If you connect directly to your printer with a USB cable, use the HP Utility.
From the front panel, press , then , then Setup > Connectivity > Advanced >
Embedded Web Server > Allow EWS > On.
If you are using a proxy server, try bypassing the server and accessing the Web server directly.
●In Internet Explorer 6 for Windows, go to Tools > Internet Options > Connections > LAN
Settings, and check the Bypass proxy server for local addresses box. Alternatively, for
more precise control, click the Advanced button and add the printers IP address to the list of
exceptions, for which the proxy server is not used.
●In Safari for Mac OS, go to Safari > Preferences > Advanced and click the Proxies:
Change Settings button. Add the printers IP address or its domain name to the list of
exceptions, for which the proxy server is not used.
If you still cannot connect, switch the printer off and back on with the Power key on the front panel.
Cannot connect to the Internet
If your printer has difficulty in connecting to the Internet, it may start the Connectivity Wizard
automatically. You can also start the wizard manually at any time.
●From the Embedded Web Server: select Support > Connectivity troubleshooting >
Connectivity wizard.
NOTE:You cannot change connectivity settings from the Embedded Web Server.
●
From the front panel: Press , then , then Connectivity > Connectivity wizard.
●
From the front panel: Press 
, then , then Internal prints > Service information
prints > Print connectivity config. In this case, the results are printed out.
ENWWCannot access the HP Utility
193
 
						

							NOTE:The results printed out are from the last run of the Connectivity wizard, so you must
already have run the Connectivity wizard in order to get any results.
The Connectivity Wizard performs a series of tests automatically. You can also choose to perform
individual tests. From the front panel, press 
, then , then Connectivity > Diagnostics &
troubleshooting > Diagnostics & troubleshooting. The following options are available.
●All tests
●Network connectivity test: Check the printers connection to the local area network.
●Internet connectivity test: Check the printers connection to the Internet.
●HP Designjet ePrint & Share test: Check the printers connection to HP Designjet ePrint &
Share.
●HP ePrint Center test: Check the printers connection to the HP ePrint Center.
●Firmware update test: Check the printers connection to HPs firmware update servers.
If any test fails, the printer describes the problem and recommends how to solve it. You can modify
settings and rerun the test, unless you are using the Embedded Web Server or the settings are
protected.
Web Services issues
For any issues with HP ePrint, please refer to the HP ePrint Center: .
For any issues with HP Designjet ePrint & Share, please refer to the HP Designjet ePrint & Share
website: 
.
Automatic file system check
When you turn on the printer, you will occasionally see a front panel display similar to the one shown
below.
A file system check is taking place; it can take up to 40 minutes. Please wait until it finishes.
CAUTION:If you turn the printer off before the file system check has finished, the file system could be
seriously damaged, making the printers hard disk unusable. In any case, the file system check will
restart from the beginning whenever you turn the printer on again.
A file system check is scheduled every 90 days, in order to maintain the hard disks file system
integrity.
194 Chapter 19   Troubleshooting general printer issues ENWW
 
						

							NOTE:When the printer is powered back on, it takes about three minutes to initialize and check and
prepare the printheads. However, it can take up to 40 under some conditions, for example, when the
printer has not been used for a long period of time and requires more time to prepare the printheads.
Alerts
Your printer can communicate two types of alerts:
●Errors: Mainly alerting you to the fact that the printer is unable to work normally. However, in the
printer driver, errors can also alert you to conditions that could ruin the print, such as clipping,
even if the printer is able to print.
●Warnings: Alert you when the printer needs attention either for an adjustment, such as a
calibration or for a possible unprintable situation, such as a preventive maintenance or low ink.
There are four different alerts communicators within your printers system.
●Front-panel display: The front panel shows only the most relevant alert at a time. In the case of
a warning, it disappears after a timeout. There are permanent alerts, such as ink cartridge low on
ink, that reappear when the printer becomes idle and there is not another more severe alert.
TIP:From the front panel display you can configure paper mismatch alerts, see Paper suitability
options (T1300 series) on page 26.
●Embedded Web Server: The upper-right corner of the Embedded Web Server window shows
the printer status. If there is an alert in the printer, the status shows the alert text.
●Driver: The driver shows alerts. The driver warns about job configuration settings that may
produce a problem in the final output. If the printer is not ready to print, it displays a warning.
●HP Utility: To see alerts, go to the Overview tab and review the Items needing attention
list on the right-hand side.
By default, alerts are displayed only when you are printing. If alerts are enabled and there is a
problem that prevents a job from completing, you see a pop-up window, which explains the
reason for the problem. Follow the instructions to achieve your required result.
NOTE:There are environments that do not support bidirectional communication, for example: a
Windows computer connected to the printer with USB. In those cases, alerts do not reach the job
owner.
ENWWAlerts
195
 
						

							20 Front-panel error messages
Occasionally you may see one of the following messages appear on the front-panel display. If so,
please follow the advice in the Recommendation column.
If you see an error message that does not appear here, and you feel in doubt about the correct
response, or if the recommended action does not seem to solve the problem, contact HP Support. See
Contact HP Support on page 203.
Table 20-1  Text messages
Message Recommendation
[Color] cartridge altered Check the cartridge.
[Color] cartridge has expired Replace the cartridge. See 
Handling ink cartridges and
printheads on page 125.
[Color] cartridge is low on ink Ensure that you have a new cartridge of the same color
ready.
[Color] cartridge is missing Insert a cartridge of the correct color. See 
Handling ink
cartridges and printheads on page 125.
[Color] cartridge is out of ink Replace the cartridge. See 
Handling ink cartridges and
printheads on page 125.
[Color] cartridge is very low on ink Ensure that you have a new cartridge of the same color
ready.
[Color] printhead #[n] error: not present Insert the correct printhead. See 
Handling ink cartridges and
printheads on page 125.
[Color] printhead #[n] error: please remove Remove the incorrect printhead and insert a new printhead of
the correct type (color and number). See 
Handling ink
cartridges and printheads on page 125.
[Color] printhead #[n] error: replace Remove the non-functional printhead and insert a new
printhead of the correct type (color and number). See
Handling ink cartridges and printheads on page 125.
[Color] printhead #[n] error: reseat Remove and reinsert the same printhead, or try cleaning the
electrical connections. If necessary, insert a new printhead.
See 
The front-panel display recommends reseating or
replacing a printhead on page 183.
Cutter replacement advised Contact HP Support to replace the cutter. See 
Contact HP
Support on page 203.
Job queue notification Cancel, resume or delete the job. See 
Job queue management
(T790 PS and T1300 series) on page 77.
Maintenance #1 advised Contact HP Support. See 
Contact HP Support on page 203.
Maintenance #2 advised Contact HP Support. See 
Contact HP Support on page 203.
196 Chapter 20   Front-panel error messages ENWW
 
						

							Table 20-1  Text messages (continued)
Message Recommendation
Paper loaded incorrectly: remove paper Remove the paper and try to reload it.
Paper mispositioned: remove paper Remove the paper and try to reload it.
Paper path error: incorrectly loaded Unload and reload the paper.
Paper path error: misaligned Unload and reload the paper.
Printhead replacement incomplete. Restart it. Restart the printhead replacement process.
Printheads need individual testing. Do replacement Test the printheads using the Image Diagnostics Print (see the
Image-quality troubleshooting guide) and replace any that are
not working correctly.
Replace [color] cartridge Replace the cartridge. See 
Handling ink cartridges and
printheads on page 125.
Reseat [color] cartridge Remove and reinsert the same cartridge. See 
Handling ink
cartridges and printheads on page 125.
Table 20-2  Numerical error codes
Error code Recommendation
01.0, 01.1, 01.2 Restart the printer.
06:03 Restart the printer.
08:04 Restart the printer. If the problem persists, update the printers firmware. See 
Update the
firmware on page 138.
08:08 Retry the operation that you were attempting. If it fails again, restart the printer. If the problem
persists, update the printers firmware. See 
Update the firmware on page 138.
21, 21.1, 21:03, 21.1:03,
21:13, 21.2:13, 22.0, 22.1,
22.2, 22.3, 22.x:03, 24Restart the printer.
26:01, 26.x:01 Bad contact detected in an ink cartridge (if present, x refers to the cartridge in slot x). Remove
and reinsert the cartridge. If necessary, insert a new cartridge.
26:14 Update your printers firmware. See 
Update the firmware on page 138.
27:01, 27.x:01 Too many printhead nozzles are not working (if present, x refers to the printhead in slot x).
Remove and reinsert the printhead, or try cleaning the electrical connections. If necessary,
insert a new printhead. See 
The front-panel display recommends reseating or replacing a
printhead on page 183.
27:03 Printhead error. Restart the printer.
27:14 Update your printers firmware. See 
Update the firmware on page 138.
31:03, 41:03, 42:03,
45.1:03, 45.2:03, 47:03,
56:03Restart the printer.
61:01 The file format is wrong and the printer cannot process the job. You may have sent a
PostScript, PDF, TIFF or JPEG job to a non-PostScript printer. If the job is password-protected,
try sending it without password protection. Otherwise, update your printers firmware and try
again. See 
Update the firmware on page 138.
61:04.1, 61:04.2 Update your printers firmware. See 
Update the firmware on page 138.
ENWW197
 
						

							Table 20-2  Numerical error codes (continued)
Error code Recommendation
61:08.1 Resend the job without password protection.
62, 62:04, 63 Update your printers firmware. See 
Update the firmware on page 138.
63:01 The printer has failed to get an IP address. Connect to another network or change the IPv4
configuration.
63:04, 64 Update your printers firmware. See 
Update the firmware on page 138.
64.1:01 The external hard disk has been removed while it was in use. Please reconnect it and restart
the printer.
64:04, 65, 65:04 Update your printers firmware. See 
Update the firmware on page 138.
66:08 The job cannot be printed on the paper type that is loaded.
67, 67:04 Update your printers firmware. See 
Update the firmware on page 138.
68:03 Restart the printer.
71.04 Out of memory. To avoid this, in the HP-GL/2 and HP RTL driver select the Advanced tab
and then Send job as a bitmap.
71:03 Restart the printer.
71:04 Update your printers firmware. See 
Update the firmware on page 138.
74:04, 74.1:04 The firmware upgrade has failed. Press OK and try again. See 
Update the firmware
on page 138.
74.1 Try the firmware update again. Do not try to use your computer while the update is in
progress.
74.8:04 The firmware upgrade has failed. Your firmware file may be incorrect; try to download it
again. See 
Update the firmware on page 138.
76:03 Restart the printer.
77:04, 78.1:04 Update your printers firmware. See 
Update the firmware on page 138.
78:08 Borderless printing not possible; setting ignored..
79:03 Restart the printer.
79:04, 79.1:04 Update your printers firmware. See 
Update the firmware on page 138.
81:01 Please follow the instructions on the front panel. You may be asked to run a test procedure and
write down a numeric code before contacting HP Support. See 
Contact HP Support
on page 203.
81:03, 84:03 Restart the printer.
86:01 Please follow the instructions on the front panel. You may be asked to run a test procedure and
write down a numeric code before contacting HP Support. See 
Contact HP Support
on page 203.
94, 94.1, 94:08 Restart color calibration. See 
Color calibration on page 86.
94:02 Color calibration failed. Check that the paper type that is loaded corresponds to the paper
type that you have selected.
198 Chapter 20   Front-panel error messages ENWW
 
						

							The system error log
The printer saves a log of system errors that you can access in the following ways.
Using a USB flash drive
1.Create an empty file named pdipu_enable.log in a USB flash drive.
2.Insert the USB flash drive into the Hi-Speed USB host port at the front of the printer. The log will be
automatically copied into the drive.
Using the Embedded Web Server
1.In your Web browser, go to http://printer IP address/hp/device/webAccess/log.html.
2.The Embedded Web Server will send you a file called log.tar.gz containing the system error log.
ENWWThe system error log
199
 
						

							21 HP Customer Care
●Introduction
●
HP Professional Services
●
HP Instant Support
●
HP Proactive Support
●
Customer Self Repair
●
Contact HP Support
200 Chapter 21   HP Customer Care ENWW
 
						

							Introduction
HP Customer Care offers award-winning support to ensure you get the most from your HP Designjet,
providing comprehensive, proven support expertise and new technologies to give you unique end-to-
end support. Services include setup and installation, troubleshooting tools, warranty upgrades, repair
and exchange services, phone and Web support, software updates and self-maintenance services. To
find out more about HP Customer Care, please visit us at:
http://www.hp.com/go/graphic-arts
or call us on the telephone (see 
Contact HP Support on page 203). To register your warranty:
http://register.hp.com/
HP Professional Services
Knowledge Center
Enjoy a world of dedicated services and resources to ensure you always get the best performance from
your HP Designjet printers and solutions.
Join the HP community at the Knowledge Center, your large-format printing community, for 24×7
access to:
●Multimedia tutorials
●Step-by-step how-to guides
●Downloads: the latest printer firmware, drivers, software, paper presets, etc.
●Technical support: online troubleshooting, customer care contacts and more
●Workflows and detailed advice for completing various printing tasks from particular software
applications
●Forums for direct contact with the experts, both HP and your colleagues
●Warranty tracking online, for your peace of mind
●Latest product information: printers, supplies, accessories, software, etc.
●Supplies Center for all you need to know about ink and paper
The Knowledge Center can be found at the following locations, depending on your printer:
●
http://www.hp.com/go/T790/knowledgecenter
●
http://www.hp.com/go/T790ps/knowledgecenter
●
http://www.hp.com/go/T1300/knowledgecenter
●
http://www.hp.com/go/T1300ps/knowledgecenter
By customizing your registration for the products you have purchased and your type of business, and
by setting your communication preferences, you decide the information you need.
ENWWIntroduction
201
 
						

							HP Start-Up Kit
The HP Start-Up Kit is the DVD that comes with your printer; it contains the printers software and
documentation.
HP Care Packs and Warranty Extensions
HP Care Packs and Warranty Extensions allow you to extend your printers warranty beyond the
standard period.
They include remote support. On-site service is also provided if necessary, with two alternative
response-time options.
●Next business day
●Same business day, within four hours (may not be available in all countries)
For more information on HP Care Packs, please visit 
http://www.hp.com/go/printservices.
HP Installation
The HP Installation service unpacks, sets up and connects the printer for you.
This is one of the HP Care Pack services; for more information, please visit 
http://www.hp.com/go/
printservices.
HP Instant Support
HP Instant Support Professional Edition is HPs suite of troubleshooting tools that collect diagnostic
information from your printer and match it with intelligent solutions from HPs knowledge bases,
allowing you to resolve problems as quickly as possible.
You can start an HP Instant Support session by clicking on the link provided on the Troubleshooting
page of your printers Embedded Web Server. See 
Access the Embedded Web Server on page 33.
To be able to use HP Instant Support:
●You must have a TCP/IP connection to your printer, because HP Instant Support is accessible only
through the Embedded Web Server.
●You must have access to the World Wide Web, because HP Instant Support is a Web-based
service.
HP Instant Support is currently available in English, Korean, Simplified Chinese and Traditional
Chinese.
You can find more information about HP Instant Support at 
http://www.hp.com/go/ispe.
HP Proactive Support
HP Proactive Support helps reduce costly printer downtime by preemptively identifying, diagnosing and
resolving printer issues before they become problems for you. HPs Proactive Support tool is designed
to help businesses of all sizes reduce support costs and maximize productivity—all with the click of a
mouse.
202 Chapter 21   HP Customer Care ENWW