HP DesignJet 9000s User Manual

Parameters:
●NORMAL — Normal fan suction level
●LOW — Low fan suction level
Initial temperature setting for the front heater (FRONT HEATER T)
Use this option to set the front heater temperature for the selected media type.
Parameters: 15 °C to 55 °C, or ** to turn the heater off.
NOTEFor Celsius/Fahrenheit conversions:
F = (9 × C / 5) + 32
C = 5 × (F - 32) / 9
NOTEThis value will only be applied if the HEATER PREF option is set to HEAT PANEL.
Initial temperature setting for the print heater (PRINT HEATER...

Parameters: 15 °C to 55 °C, or ** to turn the heater off.
NOTEFor Celsius/Fahrenheit conversions:
F = (9 × C / 5) + 32
C = 5 × (F - 32) / 9
NOTEThis value will only be applied if the HEATER PREF option is set to HEAT PANEL.
Color stripe setting (COLOR STRIPE)
A color stripe is printed on all plots. This ensures that all printhead nozzles are used in all prints, even if
the printed image does not include certain colors. The color stripe avoids drying of nozzles even if they
are not used for a long time...

Parameters:
●NORMAL — Default
●HIGHLIGHT — Modifies the printhead firing mode
HintThe HIGHLIGHT mode action of the printheads can be useful to avoid nozzles out in a
specific color when printing a large number of images that do not use that specific color.
NOTE HIGHLIGHT reduces the printing speed. We advise you to clean the printheads and
reset the option to NORMAL.
Printhead height setting (PH HEIGHT VAL)
Use this option to set the printhead height for the selected media type. Change this setting when...

YY: Ink color
Display order: K -> Lm -> Lc -> Y -> M -> C
Parameters: sign (+/-), value (-32 to +31)
Printhead cleaning mode (PH CLEANING)
Use this option to select an automatic printhead cleaning mode for the selected media type.
Parameters:
●START & END — Performs cleaning at the start or end of the print based on the print history record.
●DURING PRINT — Performs cleaning after a certain period of time even during printing.
NOTE DURING PRINT can cause some banding.
NOTEWhen the TENSION winding or BACK...

Media advance preference (ADVANCE PREF)
Use this option to define printer front panel priority or software RIP priority for media advance settings
for the selected media type. If you select software RIP priority, the printer will ignore media advance
settings that are defined on the printer front panel and use the settings from the RIP.
Parameters:
●SOFTWARE  — Settings in the RIP takes priority.
●FRONT PANEL — Settings in the printer front panel take priority.
Print mode preference (PRINT MODE PREF)
Use...

Parameters:
●CYCLES  — Number of passes
Printhead rest time (PH REST TIME)
Use this option to define the amount of time the printing carriage will pause between passes for the
selected media type.
Parameters:
●TIME  — Time in minutes and seconds
Printhead temperature rest (PH TEMP REST)
Use this option if you want printing to pause if there is a gap between the set temperature of the media
print heater and the printhead temperature is too high.
Parameters:
●ON  — Pauses printing
●OFF — Printing...

 12345
NAMEPAPERGlossyMatteBannerBLT_B (Backlit)
MEDIA ADV.
VALUE(Base) +0.00%(Base) +0.16%(Base) +0.16%(Base) +0.14%(Base) +0.14%
DRY TIME VALUE0 sec.0 sec.0 sec.0 sec.0 sec.
PRINT MODENORMALNORMALNORMALNORMALNORMAL
PRINT
DIRECTIONBIDIRBIDIRBIDIRBIDIRBIDIR
FLATTEN TIMENoneNoneNoneNoneNone
USE EDGE
GUARDYESYESYESYESYES
MEDIA ADV.
MODEFWD ONLYFWD ONLYFWD ONLYFWD ONLYFWD ONLY
TUR MODELOOSELOOSELOOSELOOSELOOSE
LEADING EDGENORMALNORMALNORMALNORMALNORMAL
VACUUM LEVELNORMALNORMALNORMALNORMALNORMAL
FRONT...

Media advance calibration
Media advance calibration is defined by using the M.ADV menu. Press the ► key to define and set
values.
Media advance calibration print
Select MEDIA ADV PRINT to print a calibration pattern that will indicate optimal media advance values.
Two patterns are available: the ROUGH pattern prints a media advance pattern in 0.25% steps between
99.0 and 101.0 %; the DETAIL pattern prints a media advance pattern in 0.06% steps starting from the
current setting ±0.12%.
Use the ROUGH...

Select a parameter based on your print mode.
Parameters:
●NORMAL — standard and high speed print modes
●H-QUALITY — high quality print mode
●H-DENSITY — high density print mode
●H-QUALITY2 — high quality print mode
●H-DENSITY2 — high density print mode
●DRAFT — draft print mode
Media back feed adjustment value
Use this option to set the value for media back feed that you obtained from the back feed adjustment
pattern.
Parameters: ±2000 pulse (±5 mm)
1 pulse=2.5µm
The PH. MAIN menu
Use the PH. MAIN menu...

Parameters:
●STORE INK SYS — Use this parameter to clean the printheads and ink path with the storage liquid
while the ink system is primed with ink, and then recharge the maintenance liquid in the printer to
ensure long-term storage. Six storage liquid cartridges and six cartridges are mandatory.
●CLEAN INK SYS — Use this parameter to clean the printhead with the cleaning liquid after long-
term storage. Six cleaning liquid cartridges and six purging cartridges are mandatory.
●CAP CLEANING — Use this...