HP DesignJet 9000s User Manual

Parameters: none.
NOTEAlways perform Cleaning (normal) after filling the cap.
If the printhead surface is not clean even after leaving the printer overnight, then contact HP
Support.
Printhead height (PH HEIGHT ADJ)
Use this menu option to adjust the printhead height.
The cap is opened after performing this operation and the carriage height can be adjusted. See How do
I... 
Change the printhead height.
Parameters: none.
The PH.RECOVERY menu
This menu is used to clean the printheads of the printer. See...

When you press the ▼ key, a media feeding message appears on the front panel.
When the ▼ key is released, media feeding stops and the top menu appears on the front panel in offline
mode.
The PRINTER menu
This menu is used to print reports on the printer status.
When the ▲ key is pressed, you can select the report that you want to print.
Configuration print (CONFIG PRINT)
This option prints information on the printer, panel settings, and media type information.
Parameters: none.
Error log information...

Parameters: none.
The ADJUST menu
This menu is used to set mechanical adjustment parameters. For details on how to print the patterns,
see Calibrate the printer.
When the ◄ key is pressed, mechanical adjustment parameters can be set.
Adjustment pattern print (TEST PRINTS)
This menu is used to print the adjustment patterns for adjusting the printer mechanically and electrically.
When the CANCEL key is pressed during printing, the print can be stopped.
Parameters:
●IQ PRINT. Prints a block pattern with...

Enter an adjustment value according to the PH TO PH adjustment pattern.
YY: Ink color
Display order: K -> Lm -> Lc -> Y -> M -> C
Parameters: sign (+/-), value (-32 to +31)
Bidirectional print position (Left) adjustment (YY BIDIR DEF(L))
Use this option to adjust the printhead bidirectional printing position (Left).
Enter an adjustment value according to the BIDIRECTION DEF adjustment pattern.
YY: Ink color
Display order: K -> Lm -> Lc -> Y -> M -> C
Parameters: sign (+/-), value (-32 to +31)...

Display order: K -> Lm -> Lc -> Y -> M -> C
Parameters: sign (+/-), value (-32 to +31)
Bidirectional print position (Right) adjustment (YY BIDIR F.D (R))
Use this option to adjust the printhead bidirectional printing position (Right) in fine draft print mode.
Enter an adjustment value according to the BIDIRECTION F.D. adjustment pattern.
YY: Ink color
Display order: K -> Lm -> Lc -> Y -> M -> C
Parameters: sign (+/-), value (-32 to +31)
The SETUP menu
This menu is used to set or display printer setup...

Parameters: ON, OFF
F/W version display (F/W VERSION)
This option displays the engine firmware version.
Parameters: none.
Main PCA version display (MAIN PCA VER)
This option displays the version number of the main PCA.
Parameters: none.
ICB board version display (CARRIAGE PCA)
This option displays the version number of the printer carriage PCA.
Parameters: none.
ASIC version display (ASIC VER)
This option displays the ASIC version.
Parameters: none.
Heater H/W version display (HEATER HW VER)
This option...

Parameters: none.
Heater F/W version display (HEATER FW VER)
This option displays the heater firmware version. If the heater cannot be recognized, --.- is displayed.
Parameters: none.
System date setting (SYSTEM DATE)
This option sets system date used in the unit in YY (year), MM (month), DD (day).
Parameters: 00/01/01 to 99/12/31.
System time setting (SYSTEM TIME)
This option sets the time for your printer.
Parameters: 00 : 00 to 23 : 59.
Factory default setting (FACTORY DEFAULT)
This option sets all...

USB speed (USB SPEED)
This option sets the USB port speed.
Parameters: HIGH, FULL
168 Chapter 14   Tell me about front panel menus ENWW
Tell me about front panel menus
 

15 Tell me about the heaters
This chapter describes temperature control, the heater front panel, parameter setup mode operations,
and error messages of the heater controller.
●The heaters
●Heater temperature settings
●Heater error messages
The heaters
The printer includes three heaters for fixing and stabilizing the printed image on the media. Each heater
is controlled separately.
1. Front heater (preheats the media)
2. Print heater (fixes the ink on to the media)
3. Rear heater (dries the ink and...

4. Media roll
5. Pressure roller
6. Grid roller
7. Carriage
8. Rear cover
WARNING! Never touch the heaters, as they can cause burns, and always take care when
touching printer components near the heaters.
Heater temperature settings
1. Heater front panel
2. Heater on/off and temperature setting keys
3. Preset temperature
4. Current temperature
Heater temperatures are preset automatically for all media types. Under normal operating conditions
you do not need to set the temperature.
Use the heater front...