HP DesignJet 9000s User Manual

●Front panel display (when the heater is turned on):
●Upper line: preset temperature for each heater
●Lower line: current temperature for each heater
●Front panel display (when the heater is turned off):
●Upper line: OFF for each heater
●Lower line: current temperature for each heater
The default temperature range is set between 15 °C and 55 °C.
Heater preset temperature by medium
The heater preset temperature for each media type is listed below. Preset the heater temperature
according to the media you...

Flow of heater temperature setting
1.If you select the media type when loading the media, the initial temperature value of each heater
for that media is set on the heater front panel:
●If the initial temperature value has been set, the heater turns on but heating does not start.
●If the initial temperature value is set to **, the heater turns off. The set temperature on the
heater front panel displays OFF.
2.If the printing job data are sent from the host (PC), either of the following operations is...

Status:Status of maintaining each heater temperature at the preset temperature on the heater front
panel.
Conditions: 1. If the heater ON/OFF setting on the heater front panel is set to ON and a print command
is received.
2. Under condition (1) above, and the time specified by the delay time after the print end
command was received.
Maintaining the standby temperature
Function:To shorten the time needed to reach the preset temperature to start printing.
Status:Status of maintaining the heater temperature...

 Front heaterPrint heaterRear heater
Preset temperatureAAABBBCCC
Current temperature XXX YYY ZZZ
U stands for the temperature unit: C (Celsius) or F (Fahrenheit).
The temperature is measured every 5 seconds and refreshed.
Display — heater on
When each heater is heated, a plus sign (+) is displayed in place of the unit of each heater current
temperature on the second line. The unit display is restored at the completion of heating. In the display
example shown above, the front heater is heated.
Display —...

No.ItemItem display
(upper line)Parameters
display (lower
line)DescriptionInitial value
2Heat suspending
time after printingDELAY TIME00 to 30 MINUTESUNIT: minute05 MINUTES
3Standby heating
time after
completion of
DELAY TIMESTANDBY TIME0, 30, 60, 90,
120, ENDLESSUnit: minutes30
4Version displayVERSIONFW=vv.r HW=vv.rDisplay only–
5DiagnosticsDIAGNOSTICSNO, YESNO: Does not
perform the
diagnostics.
YES: Performs
the diagnostics.NO
6Display languageLANGUAGEENGLISH
JAPANESE–ENGLISH
7 Exit setup mode EXIT...

●Rear heater thermistor temperature error (-10 °C or less, 70 °C or more)
●Print heater thermistor temperature error (-10 °C or less, 70 °C or more)
●Front heater thermistor did not reach the preset temperature after 15 minutes
●Rear heater thermistor did not reach the preset temperature after 15 minutes
●Print heater thermistor did not reach the preset temperature after 15 minutes
●Switch test error occurs in the diagnostics
●Zero cross error occurs in the diagnostics
176 Chapter 15   Tell me about the...

16 Tell me about printer specifications
●Specifications
●Ecological specifications
ENWW177
Tell me about printer
specifications
 

Specifications
ItemSpecification / Function
Print technologyPiezo-electric inkjet printheads
Resolution — High quality720 dpi × 720 dpi
Resolution — Standard720 x 720 dpi
Resolution — Fine draft540 x 720 dpi
Resolution — Draft720 x 360 dpi
Print speedAbout four minutes / A0 with 4-pass printing (changes according to surrounding
temperature and printhead temperature)
Media feed/delivery directionFront media supply, rear media delivery
Media typePVC, banner, Vinyl chloride, Tarpaulin
Media widthMaximum 64...

Ecological specifications
For the up-to-date ecological specifications of your printer, please go to http://www.hp.com/ and search
for “ecological specifications”.
ENWWEcological specifications 179
Tell me about printer
specifications
 

180 Chapter 16   Tell me about printer specifications ENWW
Tell me about printer
specifications