HP Color LaserJet CM4730 User Manual

							Menu itemSub-menu itemSub-menu itemValuesDescription
General Copy
BehaviorScan Ahead Enabled (default)
DisabledTurn on no-wait scanning. With Scan Ahead
enabled, the pages in the original document
are scanned to disk and held until the device
becomes available.
Auto Print Interrupt Enabled
Disabled (default)When this feature is enabled, copy jobs can
interrupt print jobs that are set to print multiple
copies.
The copy job is inserted into the print queue
at the end of one copy of the print job. After
the copy job is complete, the device
continues printing the remaining copies of the
print job.
Copy Interrupt Enabled
Disabled (default)When this feature is enabled, a copy job that
is currently printing can be interrupted when
a new copy job is started. You are prompted
to confirm that you want to interrupt the
current job.
First Copy Speed No early warm up
(default)
Early warm up 
Alternative
Letterhead Mode No (default)
Yes 
Table 2-15  Device Behavior menu (continued)
ENWWDevice Behavior menu 45
 
						

							Menu itemSub-menu itemSub-menu itemValuesDescription
General Printing
BehaviorOverride A4/Letter No
Yes (default)When this feature is enabled, the job prints on
letter-size paper when an A4 job is sent but
no A4-size paper is loaded in the device (or
prints on A4 paper when a letter-size job is
sent but no letter-size paper is loaded). This
option also overrides A3 with ledger-size
paper and ledger with A3-size paper.
Manual Feed Enabled
Disabled (default)When this feature is enabled, the user can
select manual feed from the control panel as
the paper source for a job.
Courier Font Regular (default)
DarkSelect which version of the Courier font you
want to use.
Wide A4 Enabled
Disabled (default)Change the printable area of A4-size paper.
If you enable this option, eighty 10-pitch
characters can be printed on a single line of
A4 paper.
Print PS Errors Enabled
Disabled (default)Select whether a PostScript (PS) error page
is printed when the device encounters a PS
error.
Print PDF Errors Enabled
Disabled (default)Select whether a PDF error page is printed
when the device encounters a PDF error.
Personality Auto (default)
PCL
PDF
PSSelect the printer language that the device
should use.
Normally, you should not change the
language. If you change the setting to a
specific language, the device does not
automatically switch from one language to
another unless specific software commands
are sent to the device.
Table 2-15  Device Behavior menu (continued)
46 Chapter 2   Control panelENWW
 
						

							Menu itemSub-menu itemSub-menu itemValuesDescription
 PCL Form LengthType a value
between 5 and 128
lines. The factory
default is 60 lines.PCL is a set of printer commands that
Hewlett-Packard developed to provide
access to printer features.
OrientationPortrait (default)
LandscapeSelect the orientation that is most often used
for print jobs. Select Portrait if the short edge
is at the top or Landscape if the long edge is
at the top.
Font SourceSelect the source
from the list.Select the font source for the user-soft default
font.
Font NumberType the font
number. The range is
between 0 and 999.
The factory default is
0.Specify the font number for the user soft
default font by using the source that is
specified in the Font Source menu item. The
device assigns a number to each font and
lists it on the PCL font list (available from the
Administration menu).
Font PitchType a value
between 0.44 and
99.99. The factory
default is 10.00.If Font Source and Font Number indicate a
contour font, use this feature to select a
default pitch (for a fixed-spaced font).
Font Point SizeType a value
between 4.00 and
999.75. The factory
default is 12.00.If Font Source and Font Number indicate a
contour font, use this feature to select a
default point size (for a proportional-spaced
font).
Symbol SetPC-8 (default)
(50 additional symbol
sets from which to
choose)Select any one of several available symbol
sets from the control panel. A symbol set is a
unique grouping of all the characters in a font.
Append CR to LFNo (default)
YesConfigure whether a carriage return (CR) is
appended to each line feed (LF) encountered
in backwards-compatible PCL jobs (pure text,
no job control).
Suppress Blank
PagesNo (default)
YesThis option is for users who are generating
their own PCL, which could include extra form
feeds that cause blank pages to be printed.
When Yes is selected, form feeds are ignored
if the page is blank.
Media Source
MappingStandard (default)
ClassicSelect and maintain input trays by number
when you are not using the device driver, or
when the software program has no option for
tray selection.
Table 2-15  Device Behavior menu (continued)
ENWWDevice Behavior menu 47
 
						

							Print Quality menu
Administration > Print Quality
Table 2-16  Print Quality menu
Menu itemSub-menu itemValuesDescription
Adjust ColorHighlightsCyan Density. Magenta
Density. Yellow Density.
Black Density
+5 to –5. Default is 0.Adjust the darkness or lightness of highlights on a
printed page. Lower values represent lighter highlights
on a printed page, and higher values represent darker
highlights on a printed page.
MidtonesCyan Density. Magenta
Density. Yellow Density.
Black Density
+5 to –5. Default is 0.Adjust the darkness or lightness of midtones on a
printed page. Lower values represent lighter midtones
on a printed page, and higher values represent darker
midtones on a printed page.
ShadowsCyan Density. Magenta
Density. Yellow Density.
Black Density
+5 to –5. Default is 0.Adjust the darkness or lightness of shadows on a
printed page. Lower values represent lighter shadows
on a printed page, and higher values represent darker
shadows on a printed page.
Set RegistrationTest PagePrintShift the margin alignment to center the image on the
page from top to bottom and from left to right. You can
also align the image on the front with the image printed
on the back.
Print a test page for setting the registration.
SourceAll trays
Tray : 
(choose a tray)Select the source input tray for printing the Set
Registration page.
Adjust Tray Shift from -20 to 20 along
the X or Y axes. 0 is the
default.Perform the alignment procedure for each tray.
When it creates an image, the device scans across the
page from side to side as the sheet feeds from top to
bottom into the device.
The scan direction is referred to as X. X1 is the scan
direction for the first side of a 2-sided page. X2 is the
scan direction for the second side of a 2-sided page.
The feed direction is referred to as Y.
Print Modes Configure which mode is associated with which paper
type.
Auto Sense Mode Tray 1 AutosenseFull Sensing (default)
Expanded Sensing
Transparency OnlyWhen Expanded Sensing is selected, the device
recognizes normal paper, overhead transparencies,
glossy paper, and tough paper. When Transparency
Only is selected, the device recognizes only overhead
transparency and non-overhead transparency types.
Tray 2–4 SensingExpanded Sensing
Transparency Only
(default)When Expanded Sensing is selected, the device
recognizes normal paper, overhead transparencies,
glossy paper, and tough paper. When Transparency
Only is selected, the device recognizes only overhead
transparency and non-overhead transparency types.
48 Chapter 2   Control panelENWW
 
						

							Menu itemSub-menu itemValuesDescription
OptimizeCACO3 In countries/regions where paper is expensive, this
compound is added to paper to make it less expensive
to produce. This compound makes the paper dusty,
which affects print quality.
Background1  
Background2  
Registration  
Long Paper  
Pre-rotation  
Re-transfer  
Tray 1  
Belt Contact  
Restore Optimize  
Color REt Enabled (default)
DisabledEnable or disable Resolution Enhancement
technology (REt), which produces print output with
smooth angles, curves, and edges.
Calibration/Cleaning Auto CleaningEnabled
Disabled (default)When auto-cleaning is on, the device prints a cleaning
page when the page count reaches the value that is set
in Cleaning Interval.
Cleaning Interval1000
(default)
2000
5000
10000
20000Set the interval when the cleaning page should be
printed. The interval is measured by the number of
pages printed.
Auto Cleaning SizeLetter
A4Select the size of paper to use for the cleaning page.
Process Cleaning PageProcessUse this feature to create and process a cleaning page
for cleaning excess toner off the pressure roller in the
fuser. The process takes up to 2.5 minutes.
Quick CalibrationCalibratePerforms partial MFP calibrations.
Full CalibrationCalibrate Performs all MFP calibrations.
Table 2-16  Print Quality menu (continued)
ENWWPrint Quality menu 49
 
						

							Troubleshooting menu
Administration > Troubleshooting
NOTEMany of the menu items under the Troubleshooting menu are for advanced
troubleshooting purposes.
Table 2-17  Troubleshooting menu
Menu itemSub-menu itemSub-menu itemValuesDescription
Event Log  PrintThis shows the event codes and their
corresponding engine cycles on the control-
panel display.
Calibrate Scanner  CalibrateUse this feature to compensate for offsets in
the scanner imaging system (carriage head)
for ADF and flatbed scans.
You might need to calibrate the scanner if it
is not capturing the correct sections of
scanned documents.
PQ Troubleshooting  PrintPrint various diagnostic pages that help solve
print-quality problems.
Fax T.30 TracePrint T.30 Report  Print or configure the fax T.30 trace report. T.
30 is the standard that specifies
handshaking, protocols, and error correction
between fax machines.
When to Print Report Never auto print
(default)
Print after any fax job
Print after fax send
jobs
Print after any fax
error
Print after send
errors only
Print after receive
errors only
Fax Transmit Signal
Loss  A value between 0
and 30. The default is
0.Set loss levels to compensate for phone-line
signal loss. Do not modify this setting unless
requested to do so by an HP service
representative because it could cause the fax
to stop functioning.
Fax V.34  Normal (default)
OffDisable V.34 modulations if several fax
failures have occurred or if phone line
conditions require it.
Fax Speaker Mode  Normal (default)
DiagnosticA technician can use this feature technician
to evaluate and diagnose fax issues by
listening to the sounds of fax modulations.
Paper Path Sensors   Initiate a test of the paper-path sensors.
Diagnostic Page  PrintPrint a diagnostic page that includes color
swatches and the EP parameters table.
50 Chapter 2   Control panelENWW
 
						

							Menu itemSub-menu itemSub-menu itemValuesDescription
Disable Cartridge
Check   Use this item to enter a mode where a
cartridge (or color pair of cartridge and drum)
can be removed to determine which particular
color is the source of a problem. In this mode,
all consumable-related errors are ignored.
Paper Path Test Test Page PrintGenerate a test page for testing the paper-
handling features. Define the path for the test
in order to test specific paper paths.
Source All trays
Tray 1
Tray 2
(Additional trays are
shown, if applicable.)Specify whether the test page is printed from
all trays or from a specific tray.
Destination All bins
Stacker Bin
Standard Output BinSelect the output option for the test page.
Send the test page to all output bins or only
to a specific bin.
Duplex Off (default)
OnSelect whether the duplexer should be
included in the test.
Copies Range: 2-30,
Default=2Select how many pages should be sent from
the specified source as part of the test.
Table 2-17  Troubleshooting menu (continued)
ENWWTroubleshooting menu 51
 
						

							Menu itemSub-menu itemSub-menu itemValuesDescription
Finishing Paper Path
TestStaplesFinishing OptionsChoose from a list of
available options.Test the paper-handling features on the
finisher.
Select the option that you want to test.
Media SizeLetter
Legal
A4
Executive (JIS)
8.5 x 13Select the paper size for the test.
Media TypeSelect from a list of
types.Select the paper type for the test.
CopiesRange: 2-30,
Default=2Select the number of copies to include in the
test.
DuplexOff
OnSelect whether to use the duplexer in the test.
Test PagePrintPrint a test page to use for the test.
StackMedia SizeLetter
Legal
A4
Executive (JIS)
8.5 x 13Select the options that you want to use to test
the stacker.
Media TypeSelect from a list of
types.Select the type of media to use for the
Finishing Paper Path Test.
Copies1
10
50
100
500Select the number of copies to include in the
Finishing Paper Path Test.
DuplexOff
OnSelect whether to use the duplexer in the
Finishing Paper Path Test.
Test PagePrintPrint a test page to use for the Finishing
Paper Path Test.
Manual Sensor Test
1   This item performs tests to determine
whether the paper-path sensors are
operating correctly.
Manual Sensor Test
2      This item performs tests to determine
whether the paper-path sensors are
operating correctly.
Table 2-17  Troubleshooting menu (continued)
52 Chapter 2   Control panelENWW
 
						

							Menu itemSub-menu itemSub-menu itemValuesDescription
Component Test   Exercise individual parts independently to
isolate noise, leaking, or other issues. To start
the test, select one of the components. The
test runs the number of times specified in the
Repeat option. You might be prompted to
remove parts from the device during the test.
Press the Stop button to abort the test.
Print/Stop Test  Continuous value
from 0 to 60,000
milliseconds.
Default: 0Isolate faults by stopping the device during
the print cycle and observing where in the
process the image degrades. To run the test,
specify a stop time. The next job that is sent
to the device stops at the specified time in the
process.
Color Band TestTest Page PrintPrints a page that helps identify arcing in the
high-voltage power supplies.
Copies  Specify the number of copies to print for the
Color Band test
Scanner Tests   A service technician can use this menu item
to diagnose potential problems with the
device scanner.
Control Panel LEDs  Verify that the components of the control
panel are functioning correctly.
Display
  
Buttons  
Touchscreen  
Table 2-17  Troubleshooting menu (continued)
ENWWTroubleshooting menu 53
 
						

							Resets menu
Administration > Resets
Table 2-18  Resets menu
Menu itemValuesDescription
Clear Local Address BookClearUse this feature to clear all addresses from the address books that
are stored on the device.
Clear Fax Activity LogYes
No (default)Use this feature to clear all events from the Fax Activity Log.
Restore Factory Telecom SettingRestoreUse this option to restore the following settings to their factory default
settings: Transmit Signal Loss, V34, Maximum Baud Rate, Speaker
Mode.
Restore Factory SettingsRestoreUse this feature to restore all device settings to their factory defaults.
Clear Document Feeder
MessageClearUse this feature to clear the Order Document Feeder Kit and Replace
Document Feeder Kit warning messages.
Reset Supplies New Document Feeder Kit (Yes/
No)Notify the device that a new document-feeder kit has been
installed.
54 Chapter 2   Control panelENWW