HP Color LaserJet CM1312 User Manual

Configure the network product (HP LaserJet CM1312 (fax/
photo-card model) only)
View settings
Network configuration page
The network configuration page lists the current settings and properties of the product network card. To
print the network configuration page from the product, complete the following steps.
1.On the control panel, press Setup.
2.Use the arrow buttons to select Reports, and then press OK.
3.Use the arrow buttons to select Network report, and then press OK.
Configuration page
The...

●Manual Subnet Mask
●Manual Default Gateway
NOTE:Changing the network configuration might require you to change the browser URL before you
can communicate with the product again. The product will be unavailable for a few seconds while the
network resets.
Set password
See Turn on password protection from the control panel on page 172 for information on how to set the
product passwordl.
IP address
The product IP address can be set manually, or it can be configured automatically via DHCP, BootP, or
AutoIP....

NOTE:You can also view the IP address in the EWS or HP ToolboxFX by selecting the Advanced
Network Settings tab.
IPv4 and IPv6 settings
Only the IPv4 protocol can be configured manually. The IPv4 protocol can be set from HP ToolboxFX
or from the product control panel. The IPv6 protocol can be selected only from the product control panel.
Link speed setting
NOTE:Incorrect changes to the link speed setting might prevent the product from communicating with
other network devices. For most situations, the...

52 Chapter 5   ConnectivityENWW
 

6 Paper and print media
●Understand paper and print media use
●
Supported paper and print media sizes
●
Supported paper types and tray capacity
●
Special paper or print media guidelines
●
Load paper and print media
●
Configure tray
ENWW53
 

Understand paper and print media use
This product supports a variety of paper and other print media in accordance with the guidelines in this
user guide. Paper or print media that does not meet these guidelines might cause the following problems:
●Poor print quality
●Increased jams
●Premature wear on the product, requiring repair
For best results, use only HP-brand paper and print media designed for laser printers or multiuse. Do
not use paper or print media made for inkjet printers. Hewlett-Packard...

Supported paper and print media sizes
This product supports a number of paper sizes, and it adapts to various media.
NOTE:To obtain best print results, select the appropriate paper size and type in the print driver before
printing.
Table 6-1  Supported paper and print media sizes
SizeDimensionsTray 1
Letter216 x 279 mm (8.5 x 11 inches)
Legal216 x 356 mm (8.5 x 14 inches)
A4210 x 297 mm (8.27 x 11.69 inches)
Executive184 x 267 mm (7.24 x 10.51 inches)
A3297 x 420 mm (11.69 x 16.54 inches) 
A5148 x 210 mm...

SizeDimensionsTray 1
Envelope B5176 x 250 mm (6.7 x 9.8 inches)
Envelope Monarch98 x 191 mm (3.9 x 7.5 inches)
Postcard100 x 148 mm (3.94 x 5.83 inches)
Double postcard 148 x 200 mm (5.83 x 7.87 inches)
Supported paper types and tray capacity
Media typeWeightCapacity1Paper orientation
Every day:
●Plain
●Light
●Bond
●Recycled< 96 g/m2Up to 150 sheetsSide to be printed on face-up,
with the top edge at the back of
the tray
Presentation:
●Matte paper, mid-weight to
heavy
●Glossy paper, mid-weight to...

Media typeWeightCapacity1Paper orientation
●Preprinted
●Prepunched
●Colored
●Rough
●Tough
1Capacity can vary depending on media weight and thickness, and environmental conditions.
Special paper or print media guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory
results. When using special paper or print media, be sure to set the type and size in your print driver to
obtain the best print results.
CAUTION:HP LaserJet printers use fusers to bond...

Load paper and print media
Tray 1
Tray 1 holds up to 150 pages of 75 g/m2 (20 lb) paper, or fewer pages of heavier media (15 mm (0.6 in)).
Load media with the top forward and the side to be printed on facing down.
Media guides ensure that the media feeds correctly into the product and that the print is not skewed.
Tray 1 has side and rear media guides. When loading media, adjust the media guides to match the
length and width of the media that you are using.
NOTE:When you add new media, make sure that you...