HP Color LaserJet CM1017 User Manual
Here you can view all the pages of manual HP Color LaserJet CM1017 User Manual. The HP manuals for Printer are available online for free. You can easily download all the documents as PDF.
Page 61
The printer driver does not automatically set up the selected MFP in the Print Setup Utility. Cause Solution The PPD file is corrupt.Delete the PPD file from the following hard-drive folder: Library/ Printers/PPDs/Contents/Resources/.lproj, where is the two-letter language code for the language that you are using. Reinstall the software. See the Getting Started Guide for instructions. The interface cable might be defective or of poor quality. Replace the interface cable. Make sure to use a high-quality...
Page 62
When connected with a USB cable, the MFP does not appear in the Printer Setup Utility after the MFP is selected. Cause Solution ●Ensure there are not too many USB devices drawing power from the chain. Disconnect all of the devices from the chain, and connect the cable directly to the USB port on the host computer. ●Check to see if more than two nonpowered USB hubs are connected in a row on the chain. Disconnect all of the devices from the chain and connect the cable directly to the USB port on the host...
Page 63
6Print ●Load trays ● Print on special media ● Control print jobs ● Print on both sides of the paper ● Cancel a print job The HP ToolboxFX provides information about managing the MFP and its settings. See HP ToolboxFX. ENWW49
Page 64
Load trays Use special print media, such as envelopes, labels, HP LaserJet glossy paper, HP LaserJet Photo paper, and transparencies only in tray 1 and tray 2. NOTETray 3 is an accessory. It is referred to as optional tray 3 in this guide. CAUTION Do not fan paper before loading it into trays. Avoid overloading trays. CAUTIONDo not reuse paper that has been stapled. Staples that remain in reused paper causes damage to the MFP and requires repairs that are not covered under the warranty. Load tray 1...
Page 65
2.Feed print media into tray 1 with the side to be printed down, and the top, short edge in first. Make sure that the media is inserted far enough into the MFP for the paper-feed mechanism to grab the media. NOTE There is a short pause before the paper is picked up. NOTEWhen printing on both sides, see Print on both sides of the paper for loading instructions. Load tray 2 Access tray 2 and optional tray 3 from the front of the MFP. Each tray holds up to 250 sheets of paper. Tray 2 also supports other...
Page 66
NOTEInstructions are the same for loading media in tray 2 and optional tray 3. 1.Pull tray 2 or optional tray 3 out of the MFP and remove any paper. 2.Move the rear guides to match the paper size. Tray 2 and optional tray 3 accept several standard paper sizes. 3.When printing paper longer than Letter/A4, extend the rear of the tray until it matches the paper size. 52 Chapter 6 Print ENWW
Page 67
4.Slide the media-width guides slightly wider than the print media. NOTE Load a maximum of 10 envelopes into tray 2 with the flaps on the right side, the side to be printed facing up, and with the short edge leading into the MFP. If the envelope has a flap on a short edge, this edge must enter the MFP first. ENWW Load trays 53
Page 68
5.Load the media. NOTE If this is special paper such as labels, transparencies, HP LaserJet glossy paper, HP LaserJet Photo paper, and letterhead or printed forms, load it with the side to be printed on facing up and the top edge toward the front of the tray. For additional information about printing on special print media, see Print on special media . 6.Make sure that the stack of paper is flat in the tray at all four corners, and keep it below the height tabs on the media-length guide in the rear of...
Page 69
7.Slide the tray into the MFP. The back of the tray protrudes from the back of the MFP. NOTE When printing on both sides, see Print on both sides of the paper for loading instructions. ENWW Load trays 55
Page 70
Print on special media Table 6-1 Special media printing guidelines provides guidelines for printing on special media. When printing on a special type of media, printing speeds might be automatically changed to improve the output quality for that specific media. ●See Multifunction peripheral (MFP) specifications for media that is recommended for this MFP. ●See Media supported on this MFP for information about the size, weight, and capacity of paper and other print media that the trays support. ●See...