HP 4 Plus Manual
Have a look at the manual HP 4 Plus Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1114 HP manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Left Side Cover Removal 1Remove the Right Side Cover and the Top Cover. 2Release the 2 latch points on the Left Side Cover (front latch first) see Figure 6-5. The latches are on the inside of the Left Side Cover. 3Fold out the cover and remove. NoteWhen removing the LJ 5 left side cover, you must gently push the Tray 1 cover forward to enable the left side cover to be folded out and removed. Figure 6-5 Left Side Cover Latches Removal and Replacement 6-7
Rear Door Removal 1Remove the PC tray (Tray 2). 2Open the Rear Door. Support the door with one hand. 3Release the door support from the rear of the printer frame as follows: (see Figure 6-6) aUsing needle-nose pliers, squeeze the tabs on the end of the retaining strap. Slide the strap up and out of the printer frame. bRelease the retaining strap tab from the slot in the printer frame. cLift the tab to free it from the slot. (continued on next page) Figure 6-6 Releasing the Door Support 6-8 Removal and Replacement
4LaserJet 4/5: Flex the Rear Door to release it from its hinges. Press the middle of the door while lifting either side (Figure 6-7a). LaserJet 4 Plus: Remove the Rear Door Attaching Clip (Figure 6-7b, callouts 1 through 3). Slide the Rear Door as far as possible toward the left, then rotate to remove (Figure 6-7b, callouts 4 and 5). Figure 6-7a Releasing the Door Hinge (LaserJet 4/5) 1 2 3 A B 5 4 Figure 6-7b Releasing the Door Hinge (LaserJet 4 Plus) Removal and Replacement 6-9
Font Door Cover Removal (LJ 5 Right Front Cover Removal) LJ 4/4 Plus 1Remove the Right Side Cover, the Top Cover,and the PC Tray. 2Release the top latch (see Figure 6-8, callout 1). 3Release the (2) lower latches through the access hole in the metal cover (see Figure 6-8, callout 2 and Figure 6-9, callout 1). 4Remove the Font Door Cover. Note Figure 6-9 shows the metal side cover removed in order to show the Font Door latches. It is not necessary to remove the metal side cover to remove the Font Door. LJ 5 1Remove the right side cover, the top cover, Tray 1 door, and Tray 2. 2Remove the Right Front Cover retaining screw. 3Release the top latch. (See Figure 6-8, callout 1) 4Release the latch halfway down the right side of the cover. 5Release the (2) lower latches, one through the access hole in the metal cover (see Figure 6-8, callout 2), and one from the bottom of the printer (next to the Tray 2 guide). Figure 6-8 Font Door Removal (LaserJet 4 shown) 6-10 Removal and Replacement
Figure 6-9 Font Door Cover Latches Removal and Replacement 6-11
Multi-Purpose (MP) Tray (Tray 1) Door Removal 1Remove the PC Tray. 2Open the MP Tray door and extend the MP Tray. 3Bend the Door Slides out to release the tray from the door slides (see Figure 6-10). Place the inner door in the “up” position. LJ 4/4 Plus 4Flex the MP tray at the lower middle and release the door from its hinges (seeFigure 6-10). LJ 5 4 Slide Tray 2 to the right to release it from its hinges. Figure 6-10 Removing the MP Tray Door 6-12 Removal and Replacement
Multi-Purpose (MP) Tray (Tray 1) Removal 1Remove the Right Side Cover, Top Cover, Left Side Cover, MP Tray Door (Tray 1), and the Font Door Cover. 2Remove the PC Tray (Tray 2). 3Remove the (2) screws in the Cross-member Bracket as shown in Figure 6-11, callout 1. Remove the Cross-member Bracket. (continued on next page) Figure 6-11 Remove the Crossmember Bracket Removal and Replacement 6-13
4On the LJ 4+ and LJ 5 you must release the tray tension spring located at the left side of the tray. Use a pair of needlenose pliers to remove the spring from the tray. 5Rotate the tray down until it slides off its slotted hinges (about 120°)(see Figure 6-12). Figure 6-12 Rotate the Tray Down to Release the Hinge from its Slots 6-14 Removal and Replacement
Assemblies Removal Power Supply Removal 1Remove the Right Side Cover. 2Remove the (3) or (2) screws from the metal cover at the lower right corner of the printer (see Figure 6-13a or b, callout 1.) Remove the metal cover. Note Note which end of the connecting rod is installed into the Power Supply and which end connects into the Rocker Switch. 3Remove the Power Switch Connecting Rod (callout 2.) alift the rod clear of tab (callout 3), and remove from socket (callout 4). bRemove the rod from the Rocker Switch at the front of the printer. (continued on next page) Figure 6-13a Remove the Sheet Metal Plate (LaserJet 4) Removal and Replacement 6-15
4Remove the (2) screws from the bottom frame (see Figure 6-14, callout 1). 5Slide the power supply out the right side of the printer to access the power supply connectors. (continued on next page) Figure 6-13b Remove the Sheet Metal Plate (LaserJet 4 Plus/5) Figure 6-14 Power Supply Screws 6-16 Removal and Replacement