Honeywell Hrhd 9 User Manual

Configuration
Document 900.0856
 Rev B81
02/08
10. Highlight the box beside Daytime and press  . Use the Up and Down arrow 
buttons to set the Daytime range. The DVR will consider the remaining time range 
as the Nighttime.
11. Highlight the Actions 1 and Actions 2 tabs and the Motion Detection Actions 1 
(Figure 3-65) and Actions 2 (Figure 3-66) screens display.
Figure 3-65 Motion Detection Actions 1 Screen
The DVR can be set to react to motion detection differently for each camera. Each 
camera can be...

Configuration
82
NoteFor the Alarm-Out action, the alarm output and beep you select 
should be set to the Event mode in the Alarm-Out setup screen, 
Schedule tab (see Alarm-Out Screen, page 65).
14. Highlight the box under the Notify heading and press  . You can toggle the 
entire list On and Off by highlighting Notification and pressing  . You can 
toggle the individual items On and Off by highlighting that item and pressing  . 
Highlight OK and press   to accept your changes.
NoteFor the Notify action,...

Configuration
Document 900.0856
 Rev B83
02/08
Video Loss Screen
1. Highlight Video Loss in the Event menu and press  . The Video Loss setup 
screen (Figure 3-67) appears.
Figure 3-67 Video Loss Settings Screen
2. The DVR checks to see if anything is obscuring the camera. Highlight the slider 
bar beside Check Obscuration, and use the Left and Right arrow buttons to 
adjust the setting. The sensitivity can be set from Never to 255 (extremely 
sensitive).
3. Highlight the Actions 1 and Actions 2 tabs and...

Configuration
84
NoteFor the Record action, the camera you select should be set to 
the Event or Time & Event recording mode in the Record 
Schedule setup screen.
5. Highlight the box under the Alarm-Out heading and press  . A list of Alarm 
Outputs appears. You can associate as many Alarm-Outs with that camera as you 
wish. When the DVR detects video loss on the selected camera, it will trigger 
output signals on all the associated Alarm-Out connectors. You can also have the 
DVR’s internal buzzer sound...

Configuration
Document 900.0856
 Rev B85
02/08
8. Highlight the box under the Spot Monitor heading and press  . A list of SPOT 
monitors and cameras appears. Each SPOT monitor can be associated with a 
camera. The DVR will display the associated camera on the SPOT monitor 
whenever it detects video loss on the selected camera.
9. You can save your Video Loss changes by highlighting Save and pressing  . 
Selecting Cancel exits the screen without saving the changes.
Text-In Screen
1. Highlight Text-In in...

Configuration
86
Figure 3-71 Text-In Device (VP Filter) Settings Screen
Figure 3-72 Text-In Device (Generic Text and EPSON-POS) Settings 
Screen
3. Highlight the box beside Port, and press  . Select from None, RS232, RS485 
and USB-Serial (1~8).
NoteIf you have set the Port as None, you will not be able to make 
any changes to the screen.
NoteWhen using the USB to serial text-in device, do NOT remove the 
USB cable from the port while the system is running.
4. Highlight Setup…, and press  . Use the ATM...

Configuration
Document 900.0856
 Rev B87
02/08
NoteThe screen changes for the different types of text input devices, 
changing the parameter boxes for you to enter information.
6. Highlight the box beside Virtual Port, and press  . Select the port number to 
use. This field will be activated only when setting up the VP Filter device.
7. Highlight the box beside Transaction Start, and press  . Use the virtual 
keyboard to enter the Transaction Start string. Refer to the device manufacturer’s...

Configuration
88
Figure 3-73 Text-In Actions 1 Screen
The DVR can be set to react to text input. Text input can be associated with 
cameras, trigger an Alarm-Out connector, sound the DVR’s internal buzzer, notify 
a number of different devices, move PTZ cameras to preset positions, and/or 
display a camera on a SPOT monitor.
16. Highlight the box under the Record heading and press  . A list of cameras 
appears. You can associate as many cameras with the Text Input as you wish. If 
the DVR detects text...

Configuration
Document 900.0856
 Rev B89
02/08
NoteFor the Notify action, the notify item you select should be 
enabled in the Notification setup screen and the DVR should be 
registered in the RAS (Remote Administration System).
Figure 3-74 Text-In Actions 2 Screen
19. Highlight the desired box under the PTZ heading, and press  . A list of PTZ 
presets appears. Select the preset positions for each PTZ camera, this is where 
you want PTZ cameras to move to when the DVR detects text input.
20. Highlight...

Configuration
90
Figure 3-75 Health Check Screen
The DVR can be configured to run self-diagnostics and report the results.
2. Highlighting the box beside System and pressing   allows you to select the 
interval that you want the DVR to run self-diagnostics on the system. You can 
select from 1 hr to 30 days, or Never.
3. Highlight the Setup... box beside Check Recording and press  . The Check 
Recording screen appears. Highlighting Schedule On and pressing   toggles 
the schedules On and Off. When set to...