Honeywell Hrhd 9 User Manual

Configuration
Document 900.0856
 Rev B61
02/08
Figure 3-34 Notification Callback Setup Screen
10. Highlight LAN and press   to toggle between On and Off. When LAN is turned 
On you can change the IP addresses.
11. Highlight the IP Address box that you want to change and press  . Enter the IP 
address of the computer you want contacted during an event. You can enter up to 
five IP addresses.
12. Highlight the box beside Retry and enter the number of times you would like the 
DVR to try contacting the...

Configuration
62
Figure 3-35 Device Menu
Camera Setup Screen
1. Highlight Camera in the Devices menu and press  . The Camera setup screen 
(Figure 3-36) appears.
Figure 3-36 Camera Setup Screen
2. You can turn the camera number On or Off, and you can change the Title of each 
camera using the virtual keyboard.
3. You can also determine which cameras will display on the monitors by selecting 
Normal, Covert 1 or Covert 2 from a drop-down list in the Use column.
NoteWhen selecting Covert 1, the DVR...

Configuration
Document 900.0856
 Rev B63
02/08
Figure 3-37 Camera PTZ Setup Screen
NoteYou will only be able to set up PTZ devices if the PTZ port is set 
to RS232 or RS485. You will not be able to use a modem if you 
are using the RS232 port for PTZ control. 
5. Highlight the box in the Product column for the PTZ camera you wish to configure 
and press  . A list of PTZ devices appears.
6. Select your camera from the list and press  . You will need to connect the 
camera to the RS232 or RS485 connector...

Configuration
64
Figure 3-39 Port Setup Window
9. Configure the port’s setting based on the PTZ camera manufacturer’s instructions.
10. You can save your Camera changes by highlighting Save and pressing  . 
Selecting Cancel exits the screen without saving the changes.
Audio Setup Screen
1. Highlight Audio in the Devices menu and press  . The Audio setup screen 
(Figure 3-40) appears.
Figure 3-40 Audio Setup Screen
2. The DVR can record up to four audio inputs. Highlight the box beside the input 
and...

Configuration
Document 900.0856
 Rev B65
02/08
Alarm-Out Screen
1. Highlight Alarm-Out in the Devices menu and press  . The Alarm-Out screen 
(Figure 3-41) allows you to change the settings and establish a schedule for each 
alarm output from the DVR.
Figure 3-41 Alarm-Out Settings Screen
2. Each alarm output can be given its own title by highlighting the box under the 
Title heading and pressing  . A virtual keyboard appears allowing you to enter 
the title.
3. Highlighting the boxes under the Type...

Configuration
66
a. The Day box allows you to select the days that the alarm schedule will be 
active. The choices are: Sun, Mon, Tue, Wed, Thu, Fri, Sat, M~F, Hol and All.
b. The Range box allows you to set the time that the alarm schedule will be 
active in 15-minute increments from 00:00 to 24:00.
c. The Mode box allows you to set how the alarm reacts during the scheduled 
time. When set to On, the Alarm-Out is active during the scheduled time. 
When set to Event, the Alarm-Out is only active when...

Configuration
Document 900.0856
 Rev B67
02/08
2. Highlighting an item and pressing   toggles that item On and Off. When an 
item is On, there is a checkmark in the box beside it. The following items can be 
turned On or Off:
Remote Control — The icon   displays when the DVR can be controlled 
by the infrared remote control.
Zoom — The icon   displays on the enlarged video.
Network — The icon   displays when the unit is connected to a network via 
either Ethernet or modem.
Freeze and Sequence — The icon...

Configuration
68
Figure 3-45 Main Monitor Screen
6. Here you can adjust the display dwell time for each camera displayed in 
sequence on the main monitor. Highlight the box beside Mode and press  . 
You can select between Full Sequence and Cameo Sequence.
Pressing SEQUENCE causes the DVR to sequence cameras, and the DVR can 
sequence cameras in two modes: Full and Cameo. In the Full mode, the DVR 
sequences through the cameras and displays them full screen. In the Cameo 
mode, the bottom-right window in...

Configuration
Document 900.0856
 Rev B69
02/08
Figure 3-46 Spot Monitor Screen
10. You can define which cameras display sequentially on the Spot Monitors. 
Highlight the box in the Channels column for the desired Spot Monitor and press 
.
11. You can save your Display settings by highlighting Save and pressing  . 
Selecting Cancel exits the screen without saving the changes.
Remote Control Screen
1. Highlight Remote Control in the Devices menu and press  . The Remote 
Control setup screen (Figure 3-47)...

Configuration
70
4. Highlight the box beside Remote Control Product and select the device from the 
list.
5. You can save your Remote Control settings by highlighting Save and pressing 
. Selecting Cancel exits the screen without saving the changes.
Recording Settings
Your DVR offers a variety of flexible recording modes. You can set it up to record all the 
time or to only record events. It can be set up to continue recording once the hard disk 
drive is full by recording over the oldest video, or you...