Honeywell Hrhd 9 User Manual

Installation
Document 900.0856
 Rev B31
02/08
Connecting the Power Cord
Figure 2-17 Power Cord Connector
Connect the AC power cord to the DVR and then to a wall outlet.
WARNING!ROUTE POWER CORDS SO THAT THEY ARE NOT A 
TRIPPING HAZARD. MAKE CERTAIN THE POWER CORD 
WILL NOT BE PINCHED OR ABRADED BY FURNITURE. 
DO NOT INSTALL POWER CORDS UNDER RUGS OR 
CARPET.
THE POWER CORD HAS A GROUNDING PIN. IF YOUR 
POWER OUTLET DOES NOT HAVE A GROUNDING PIN 
RECEPTACLE, DO NOT MODIFY THE PLUG.
DO NOT OVERLOAD THE...

Installation
32 

Configuration
Document 900.0856
 Rev B33
02/08
3
Configuration
NoteYour DVR should be completely installed before proceeding. 
Refer to Chapter 2, Installation.
Front Panel Controls
Figure 3-1 16-Channel DVR Front Panel
The front panel looks and operates much like a VCR combined with a multiplexer. Many 
of the buttons have multiple functions. The buttons on the infrared remote control, while 
laid out differently, perform the same functions as those on the front panel. The 
following describes each...

Configuration
34
NoteThe infrared sensor on the DVR is just to the left of the arrow 
buttons. Make certain that nothing blocks the sensor, or the 
remote control will not function properly.
NoteYou can also use a USB mouse (not supplied) to navigate 
through the screens and menus much like you would on a 
computer.
Figure 3-2 Infrared Remote Control 

Configuration
Document 900.0856
 Rev B35
02/08
NoteSome buttons on the infrared remote control may not be 
supported, depending on the DVR model.
Table 3-1 Front Panel Buttons and Controls 
Control Description
Camera Buttons
(1 to 16)Pressing the individual camera buttons will cause the selected camera to 
display full screen. Buttons 1 to 9 are also used to enter passwords.
DISPLAY Button The DISPLAY button has two functions. First, it toggles between different 
display formats. The available formats...

Configuration
36
HDD  LED The HDD LED flickers when the DVR is recording or searching video on the hard 
disk drive.
NETWORK LED The NETWORK LED flickers when the unit is connected to a network via either 
Ethernet or modem.
POWER LED The POWER LED is lit when the unit is On.
Enter  Button The   (Enter) button selects a highlighted item or completes an entry that you 
have made during system setup.
SEARCH Button Pressing the SEARCH button enters the Search menu. Pressing the button 
again exits Search...

Configuration
Document 900.0856
 Rev B37
02/08
Turning on the Power
Connecting the power cord to the DVR turns on the unit. The unit takes approximately 
60 seconds to initialize. 
Initial Unit Setup
Before using your DVR for the first time, you will want to establish the initial settings. This 
includes settings such as time and date, display language, camera, audio, remote 
control, record mode, network and password. Your DVR can be set up using various 
screens and dialog boxes.
Throughout the screens...

Configuration
38
Figure 3-3 Login Screen
Select a User and enter the password by pressing the appropriate combination of 
Camera number buttons and then  . There is no default password when logging in 
the admin user for the first time.
NoteTo assure the secure management of the system, setting up a 
password is strongly recommended.
NoteYou can use a mouse (not supplied) to access the Login screen 
in addition to using the front panel buttons or the infrared remote 
control. Click the right mouse button...

Configuration
Document 900.0856
 Rev B39
02/08
Press MENU to enter the setup screen. 
While setting up the DVR, there will be many opportunities to enter names and titles. 
When making these entries, a Virtual Keyboard will appear.
Figure 3-5 Virtual Keyboard
Use the arrow keys to highlight the character you want in the name or title and press 
. That character appears in the title bar and the cursor moves to the next position. 
Pressing   toggles between the upper and lower case keyboards,   backspaces,...

Configuration
40
2. Highlight the Site box and press  . A virtual keyboard appears that you can use 
to enter a Site Name.
3. Once you have entered your title, highlight OK and press  .
4. Highlight the box beside System ID and press  . Change the number by 
highlighting it and using the Up and Down arrow buttons to increase and 
decrease the number from 0 to 99.
NoteThe System ID number is used to identify the unit when it is 
connected with other DVRs through the RS485 port. You cannot 
use the same ID...