Honeywell Hrhd 9 User Manual

Configuration
Document 900.0856
 Rev B51
02/08
Figure 3-21 Shutdown Screen
After selecting Shutdown and pressing  , a screen will appear telling you when it is 
safe to disconnect power.
Logout Screen
Highlight Logout in the System menu and press  . The Logout screen displays 
asking you to confirm whether or not you want to log out the current user.
Figure 3-22 Logout Screen
After selecting Logout and pressing  , the user will be logged out.
Network and Notification Setup
In the Main screen, use the...

Configuration
52
Figure 3-24 Network Setup Screen
2. Highlight the first box beside Transfer Speed. Press the Up and Down arrow 
buttons to set the Transfer Speed from 50 Kbps to 100 Mbps.
3. Highlight the second box beside Transfer Speed. You can select the unit of 
measure for the transfer speed between: bps and ips. Press   to set the 
transfer speed.
4. Highlight the box beside Quality and press  . You can select the Quality from: 
Very High, High, Standard and Low. Press   to set the Quality....

Configuration
Document 900.0856
 Rev B53
02/08
Figure 3-25 LAN (Manual) Setup Screen
2. Highlight the box beside Type and press  . You can select the type of network 
configuration from: Manual, DHCP and ADSL (with PPPoE). Select the desired 
type and press  .
3. Selecting Manual as the Type allows you to set up LAN parameters manually.
NoteYou will need to get the appropriate IP Address, Gateway and 
Subnet Mask values from your network administrator.
a. Change the numbers by highlighting them and using...

Configuration
54
Figure 3-26 Port Numbers Setup Screen
d. Change the numbers by highlighting them and using the Up and Down arrow 
buttons to increase or decrease the number.
The factory default Port settings are:
Remote Admin:  8200
Remote Callback: 8201
Remote Watch:  8016
Remote Search: 10019
NoteThe system restarts automatically after changing the port 
settings.
NoteDo NOT use the same port number for two different programs, 
otherwise, the DVR cannot be connected with the PC running 
RAS or...

Configuration
Document 900.0856
 Rev B55
02/08
Figure 3-27 LAN (DHCP) Setup Screen
5. Selecting ADSL (with PPPoE) allows you to set up the ADSL network.
NoteADSL and modem cannot be configured at the same time. If the 
DVR is configured by modem, the ADSL (with PPPoE) will not 
be selected.
Figure 3-28 LAN (ADSL) Setup Screen
a. Highlight the box beside ID and press  . A virtual keyboard appears 
allowing you to enter the ID for ADSL connection.
b. Highlight the box beside Password and press  . A virtual...

Configuration
56
NoteIf the DVR is configured for DHCP or an ADSL network, the 
DVR’s IP address might change whenever the unit is turned on.
Modem Setup
1. Highlight the Modem tab, and the Modem screen (Figure 3-29) displays.
Figure 3-29 Modem Setup Screen
NoteIf the RS232 port is in use for remote control, networking cannot 
be configured for a modem.
2. Highlight Enable and press   to toggle between On and Off. You will only be 
able to change the settings if Modem is enabled.
3. Highlight the box...

Configuration
Document 900.0856
 Rev B57
02/08
DVRNS Setup
1. Highlight the DVRNS tab, and the DVRNS screen (Figure 3-30) displays.
Figure 3-30 DVRNS Setup Screen
NoteWhen LAN settings have been changed, set up the DVRNS after 
saving your LAN changes by highlighting Save and pressing   
.
2. Highlight Use DVR Name Service and press   to toggle between On and Off.
NoteThe DVRNS (DVR Name Service) allows the DVR to use Dynamic 
IP addresses for remote connection. When this feature is On, 
you can access...

Configuration
58
NoteYou can use the domain name instead of IP address if you 
already set up the DNS Server when setting up the LAN.
4. Highlight the box beside Port and press  . Set the port number of the DVRNS 
server using the Up and Down arrow buttons to increase or decrease the 
numbers. 
5. Highlight Use NAT and press   to toggle between On and Off.
NoteWhen using the NAT (Network Address Translation) device, refer 
to the NAT manufacturer’s instructions for the proper network 
settings.
6....

Configuration
Document 900.0856
 Rev B59
02/08
Figure 3-31 WebGuard Setup Screen
2. Highlight Use WebGuard Service and press   to toggle between On and Off. 
See Appendix D, WebGuard for detailed descriptions of the WebGuard service.
3. Highlight the box beside Port and press  . Set the port number used when 
accessing WebGuard by using the Up and Down arrow buttons to increase or 
decrease the numbers.
4. You can save your Network changes by highlighting Save and pressing  . 
Selecting Cancel exits the...

Configuration
60
3. Highlight the box beside SMTP Server and press  . Use the virtual keyboard 
that appears to enter the IP address or domain name of the SMTP server. 
NoteYou will need to get the IP address or domain name of the SMTP 
Server from your network administrator.
NoteYou can use the domain name instead of IP address if you 
already set up the DNS Server when setting up the LAN.
4. Highlight the box beside Port and press  . Use the arrow buttons to enter the 
SMTP Server port number obtained...