Honeywell Hrdp H264 Manual

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  61 
02/11  
 
Icons
 
In Live  mode, icons or messages on the scr een indicate the system mode or 
status.   
 
Right -upper corner on each CH screen  
 
 Continuous Recording  
  Motion Detection Recording  
  Sensor Activated Recording  
  Continuous + Motion Alarm Recording 
  Continuous + Sensor Activated Recording  
  Motion Detection + Sensor Activated Recording  
  Emergency Recording  
  Sensor  Activated 
  Motion Detected 
  PTZ Camera  
  Audio Channel  
 
 
Right -bottom corner on full screen.  
 
 No HDD, Smart Alarm & HDD Failure  
  Using Emergency Recording  
  Using PTZ  
  Warning when  exceeding temperature  
  Showing sequence mode  
  Showing digital zoom  mode  
    
						

							Operation 
 
________________________________________________________________________\
______________________ 
62  
   
Mouse
-Over Menu  
Move the mouse  to the bottom of the monitor in live mode. The mouse -over 
menu  will instantly appear . 
 
  Sequence
 –  Click to start camera sequence.  
  Instant Recording
 –  Click to start instant recording . In instant 
recording mode, the records all channels at the recording rate 
configured in the Emergency Recording setup . 
  PTZ Mode
 –  Click to enter PTZ mode. In PTZ mode, you  can 
pan/tilt and zoom by moving the mouse pointer, referred to as a 
virtual joystick.  
  Qu
ick Search  –  Click  to automatically play back the most recent 
video clip.  
  Dock Tool Menu
 –  Click to dock the Tool menu at the bottom of 
the screen.  If  the Tool menu is not docked,    it  will be shown only 
when the you  places the mouse pointer in the lowe r portion of the 
screen.  
Note   If there is no icon in the upper  right corner of the live screen mode, 
it means that the system is not currently recording.  If this is  the 
case, you should check the recording schedule or camera setup in 
the main setup menu.  
 
    
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  63 
02/11    
Popup Menu
 
Right-click the live screen to open the Popup Menu.  
HIDE LIVE VIEW  –  Hide the selected 
camera from Live view.  
RECORD CHANGE  – Change the 
recording settings for that channel 
including PPS, quality, resolution and 
event response.  
PAGE  SEQUENCE  –  The SEQ icon is 
shown on the bottom right of the screen 
and displayed channels will be 
sequentially changed.  
FREEZE ALL  –  Pause all channels 
displayed on -screen.  
SHOW MOTION AREA  –  Display the 
motion grid for the selected camera. 
DISPLAY -PIP  – Change screen display 
to PIP.  
AUDIO  – Select an audio channel to play 
(live).  
LOGOFF  – Select to log out the active user.  
SEARCH  –  Open the Search Menu.  
PTZ  – Switch to PTZ mode. 
MENU  –  Open the Setup Menu.  
 
No Signal  
If no camera is connected to a channel,  NO SIGNAL is shown on the display 
screen.  When a camera is disconnected, the DVR will generate a warning 
sound  according to the system settings.  
 
No Permission  
The Administrator can set  different levels of authorization for each user. If a 
user is not allowed to view a certa in live or playback channel, a NO 
PERMISSION warning  is shown on the display screen.  
 
    
						

							Operation 
 
________________________________________________________________________\
______________________ 
64  
   
PTZ
 
To enter PTZ mode:  
•  Right -click the Live screen and select PTZ  on the pop- up menu, or  
•  Click the PTZ icon on the Tool menu on  the bottom of the main 
screen.  
Drag the mouse up/down or left/right to move pan/tilt position of the camera. 
As  you  move the mouse away from the center of the screen, the camera 
movement  speed increases.  You  can also zoom -in/out by  using the scroll 
wheel on the mouse.  
Note   Full PTZ functions are available  using  the front panel buttons, a 
mouse, the IR remote control, or a keyboard controller. 
PTZ Popup Menu  
Right-click the desired camera to open the PTZ Popup menu while in PTZ 
mode. 
 
 
Arrow Buttons  –  Move Camera  
M  –  Open camera’s on screen display menu (dependant on camera model 
support, see your camera’s manual for information)  
ZOOM  –  Zoom in/out on PTZ camera. Enabled by default in PTZ mode  
FOCUS  –  Adjust focus on PTZ camera.  
IRIS  – Adjust the iris on PTZ camera.  
PRESET  –  Go to preset position. S elect the preset number. The maximum 
preset number is 255  
PRESET  TOUR  –  Start preset tour. PRESET  TOUR will sequence though all 
preset positions. Can only be  enabled while in full screen mode.  
    
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  65 
02/11    
Create PTZ Preset Position 
1.
  Right -click the desired PTZ camera to open the PTZ Popup menu while in 
PTZ mode. 
2.   Select a PTZ Preset ID number . 
3.   Select MOVE under PRESET to move the camera to the desired position.  
4.   Select SET  to save the preset position.  
   
Search 
 
Searching Recorded Data  
Search recorded video on the DVR to find a specific time or event.  
 
 
 
1.   Press the SEARCH key on the front of the DVR or the remote control to 
enter Search Mode.  
2.   Select TARGET media (HDD, DVD- RW, USB). 
3.   Select the desired search method.  
    
						

							Operation 
 
________________________________________________________________________\
______________________ 
66  
   
Quick Search
 
Click the  button on the Tool menu  bar to automatically playback the 
latest video clip. 
Using the playback control icons or the jog/shuttle wheel on the front panel, 
you can search recordings  and control the speed of the playback by 2x, 4x, 
8x, 16x, or 32 times to the forward or backward directions.  
 
 
Graphic Search  
In the search mode, click the colored time bar to search the desired section of 
recorded video.  
• The white -vertical line indicates the current search time.   
•  The colors of the time bar are different according to the recording 
method selected.   
Yellow  –  Continuous recording.  
Green   – Motion -detection recording . 
Orange  –  Sensor -activated recording . 
Sky  Blue  –  Continuous  +  Motion detection recording . 
Dark orange  –  Continuous  +  Sensor -activated recording . 
Pink  –  Motion detection  + Sensor -activated  recording.  
Red  – Instant Recording.  
Dark Blue  –  Data recorded during DST (Daylight Saving Time) . 
 
 
 
Quick  Backup in Search Mode  
You can easily archive video while watching a video playback.  
In the search mode : 
1.   Press the BACKUP  on the front panel to set the Start time.  You  will see S 
[Date/Time of clip] in right bottom of the playback monitor.  
2.   Continue video p layback until you reach the end of the desired clip.  
3.   Press the BACKUP  again to set the end time. The back up menu will open  
and  you can select the backup media  ( CD/DVD or USB thumb drive ) and 
execute the backup. 
      
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  67 
02/11    
Express Search
 
Select a specific date and  time to search for recordings : 
1.   Press SEARCH on the front panel or remote control and then EXPRESS 
SEACH, or  
Click MENU on the Tool menu, select SEARCH and then select 
EXPRESS SEARCH.  
2.   Select a date from the date list and press PLAY on the front panel or 
remote to begin playing that date from the beginning, or press  Enter to 
select a time.  
3.   Select a time by scrolling to the timeline box and pressing enter. Use the 
left/right arrows to scr oll forward and backward in time. Use the up/down 
arrows to change between hours and minutes view.  
Tip   Dates with an asterisk contain recorded video data.  
Jump to First Saved Data 
Go to the first frame of the recorded data. This is the oldest image recorde d. 
 
Jump to Last Saved Data  
Go to the last frame of the recorded image. This is the latest image recorded. 
 
Event Search 
Use the Event S earch to find particular events.  
The  11 most recent events display on the first Event Search/Log page. Click 
the arrows  at the top of the screen to view the remianing entries for each date.   
You can filter the log results by SENSOR, MOTION, VIDEO LOSS, and DISK 
FULL/  
Write  th e Event log to a CD or connected USB device in text file format : 
1.   Insert a CD/DVD or USB device in the DVR . 
2.   Click SCAN, and then click EXPORT to copy the log information to the 
CD/DVD or USB device.  
3.   The Event Log is saved in a dated folder as a system.log file. 
    
						

							Operation 
 
________________________________________________________________________\
______________________ 
68  
   
Daylight Savings Search
 
Daylight Savings Search is used to find recorded data after switch ing the time 
at the end of Daylight Savings Period. The System will record data with the 
same time stamp for two hours when they are repeated. If any overlapped 
time data exists the system will display the times on this page.  
 
Search Popup Menu  
Use to access display options in Search Mode.  
•  Right -click the desired channel to open the Search Popup Menu.  
 
 
 
TIME SELECTION –  Change the Date/Time to search.  
AUDIO ON  –  ON/OFF.  
SAVE JPEG  –  Save a JPEG still image of the current frame.  
Note SAVE JPEG is only a vailable when a single camera is selected. To 
activate, select a single channel (full screen), pause playback, and 
press ENT twice, or right click the channel  to open the popup 
menu.  
 
    
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  69 
02/11    
Backup (Export)
 
Manual Export 
Back up recorded data on a CD -RW,  DVD- RW or connected USB device.  
Tip   Refer to the USB Flash Drive Approved List  in the Introduction
 
chapter.  
 
To configure a data backup:  
1.   Press  BACKUP  on  the front panel or remote control.  
or  
Click  MENU  on the hover  menu and select BACKUP.  
2.   Connect a USB device or insert a CD/DVD.  
Note The DVR supports DVD+R, and DVD -R.  DVD -RW/+RW ma y not 
operate correctly. 
3.  Select SCAN to locate the device . 
C aution  If you are using a new USB device to back up your data, you must 
format it first as FAT32.  
4.  Select the desired CAMERAs and the FROM and TO time for the backup.  
5.   Select  ESTIMATE to display estimated data size and free space available.  
    
						

							Operation 
 
________________________________________________________________________\
______________________ 
70  
 
Note  ESTIMATE must be selected first, before WRITE. If any backup 
parameters are changed (Date, Time, Channels) you must select 
ESTIMATE again.  
6.  Select the EXPORT VIEWER check box to add the Export Viewer to the 
backup file.  
Tip   Video data is saved in a proprietary format and must be viewed 
using the Export Viewer software. 
7.  Select EXPORT.  
Caution Do not shutdown the system during the backup process.  
 
Search Backup Data  
Backup files are saved in folders by date.   
 
To view a backup file:  
1.   Insert the backup file media in a computer.  
2.   Double -click the Export  Viewer program to open.  
3.   Open the desired backup file (saved by date). 
4.   Use the controls on the Export  Viewer screen to pl ayback, zoom, print or 
save an image.  
5.   Right -click the playback screen to select additional options including, 
Audio Play, Deinterlace, Digital Zoom, Save, and Print.  
Deinterlacing 
De-interlacing is often required for smooth playback of video that is record ed 
in  704x480 ( 4CIF) resolution.  
The picture comparison belo w shows the difference between Interlaced  video 
and a De- interlaced video clip. 
   
Interlaced Image   De-interlaced image  
Watermark 
When playing back an AVI video clip in the  Export Viewer, you  can verify 
whether the AVI file has been altered or not by clicking the  Watermark button.