Honeywell Hrdp H264 Manual

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  21 
02/11    
Quick Start Instructions 
1.
  Turn on the DVR. See the  Turning on the DVR  section for more details.   
2.   Log in --  Use the number buttons to enter the password when prompted 
–  The  default  password is  –  Press ENTER. 
3.   Complete System Configuration to set up the date, time and system ID. 
See the System Configuration  section for more details. 
4.   Complete Disk Configuration to set overwrite options and enable SMART 
Check. See the Disk Configuration section for more details. 
5.   Complete User Configuration to change the Admin password and add 
additional users. See the System >User Configuration section for more 
details.  
6.   Complete Camera Configuration for all attached cameras. See the 
Camera Configuration  section for more detail. 
7.   Complete PTZ Configuration for any attached Pan / Tilt / Zoom cameras. 
See the PTZ Configuration  section for more details. 
8.   Create a recording schedule. See the Record  section for more details. 
9.   Complete Sensor Configuration to enable any external devices 
connected to sensor inputs  or relay outputs. See the Record > 
Motion/Event Configuration  section for more details. 
10.  Complete Motion/Event Configuration to trigger recording on an event: 
motion,  sensor, video loss. See the Motion/Event Configuration  section 
for more details. 
11.  The DVR is now configured to record, search and playback video. See 
the  Operation  section in this manual for more information on using the 
DVR.  
 
Logging In for the First Time  
The default administrative log in information:  
 
ID:  admin 
Password:    
      
						

							Installation 
 
________________________________________________________________________\
______________________ 
22  
   
Installation
 
Front  Panel  Controls  
 
 
   
USB Port LED Lights 
•  Power  
•  HDD  
•  Record  
•  Network  
•  HDD Temp.  
DVD Drive Numeric Keypad Arrow Buttons 
Live Display 
Setup Menu 
Lock (logout) 
Search Mode 
Backup Menu 
Rotate  
Instant  Record  
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  23 
02/11    
Rear Panel Connectors
 
The rear panel of the DVR  contains virtually all of the connectors you will be 
using.  The diagram below shows the location and description of each 
connector. 
 
16 Channel 
 
   
Primary and Spot Monitor Outputs 
Power Input 
RS-232 Input  
VGA Output 
USB Port 
Video In Ports  
Video Out Ports  
Relay Output 
Sensor Input 
Audio Input  
PTZ Connection  
Audio Output  
NTSC/PAL switch 
Network Port  
						

							Installation 
 
________________________________________________________________________\
______________________ 
24  
   
8 Channel  
 
4 Channel 
 
 
   
RS-232 Input 
Video Out Ports 
Video In Ports 
Relay Outputs 
Sensor Inputs 
Audio Input Cable Connections PTZ Connection 
Primary and Spot 
Monitor Outputs Network Port 
USB Port 
Power Input 
Audio Output  NTSC/PAL switch 
Primary and Spot Monitor Outputs 
Network Port 
RS-232 Input 
VGA Output 
USB Port 
Relay Output 
Sensor Input Audio Input Cable Connection 
PTZ Connection Video Out Ports 
Video In Ports 
Power Input 
Audio Output  
NTSC/PAL switch  
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  25 
02/11    
Remote Control
 
 
   
ROTATE ALARM OSDPTZ
EXIT
REPL AY
ENTER
ZOOMFOCUSIRIS
PTZ
PRESE T
+10
LIVESEARCHBACKU
P
SETU
P
0
789
456
1
ID23
REC
S
P
-30+30
Record Toggle
 ID Select*  
 Arrow / Panorama 
  Arrow 
Rewind 
Pause 
  Arrow  
Display Options  
Play 
Fast Forward  
Log Off (Lock)  
PTZ Controls  
*The ID Select button  allows 
you to use one remote control 
for several DVRs.   
						

							Installation 
 
________________________________________________________________________\
______________________ 
26  
   
Connection Guide
 
 
Connecting the Monitor 
There are three available monitor outputs on the  DVR.  
•  Composite Monitor output for CCTV moni tor – BNC (Marked MAIN)  
•  Spot monitor output for CCTV monitor  -  BNC (Marked SPOT) 
•  VGA output for VGA monitor –  Mini-Sub D15  
 
Video Input s and Loop ing Outputs   
The HRDP DVR comes with 4/8/16 BNC video inputs on the rear of its 
chassis. Each video input has a corresponding looping BNC output for 
passing the video signal to another monitoring/recording device. 
 
Connecting to a Network  
Use the RJ45 jack on the rear of the DVR when connecting to a network.  
 
 
 
Connecting Audio  
To record audio on the DVR connect the audio source to the connections on 
the audio ports on the back of the DVR. 
To listen to live or recorded audio connect the Audio Out Port to an amplified 
speaker system. 
Note   The DVR audio output is a line level source which requires an 
amplified  speaker system. The audio input can be from an amplified 
source or line level microphone.  
    
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  27 
02/11    
Connect
ing a PTZ Camera  
The RS485 connector can be used to control Pan / Tilt / Zoom (PTZ) cameras. 
See the PTZ camera manufacturer’s manual for configuring the RS 485 
connection.  
N ote  Use the RS485 connector for external control systems such as a 
control keyboard. Connect RX -/TX - and RX+/TX+ of the control system to the 
TX -/RX - and TX+/RX+ (respectively) of the DVR.  
 
Connecting to a Sensor Input  
To make connections on the Alarm Connector Strip : Press and hold the 
button and insert the wire into the hole below the button.  To disconnect the 
wire press and hold the button above the wire and pull it out.  
Alarm In  
Use external devices to send a signal to the DVR when an  event occurs. 
Mechanical or electrical switches can be wired to the Alarm In and Ground 
(GND) connectors.  
Note All connectors marked GND are common. Connect the ground side 
of the alarm input and/or alarm output to the GND connector. 
 
Connecting to a Relay  Output  
To make connections on the Alarm Connector Strip : Press and hold the 
button and insert the wire into the hole below the button.  To disconnect the 
wire press and hold the button above the wire and pull it out.  
Alarm Out  
The DVR can activate externa l devices such as buzzers or lights. Connect the 
external device to the Alarm Out and Ground (GND) connectors. See Sensor 
Configuration in the manual for more details.  
 
Installing the Rackmount Kit  
Caution There must be a minimum 1U space between the DVR a nd any 
other items in the rack. 
1.  Attach  the rackmount brackets with the screws provided on each side of 
the DVR. Do not remove the plastic edge guards.  
2.   Mount the DVR in your rack.  
    
						

							Installation 
 
________________________________________________________________________\
______________________ 
28  
   
Turning on the DVR
 
1.  Connect camera cables.  
2.   Connect a network cable and a monitor cable. 
3.   Connect the power cable to the DVR and wait until the main screen is 
displayed on the connected monitor; this process will take approximately 
two minutes.  
Tip  See the Connection Guide section for more details  
 
Using the Power Button 
To start the DVR:   
Press and hold the Setup/Power button on the front panel of the 
DVR until the lights start to flash.  
 
To shutdown the DVR:  
Press and hold the Setup/Power button on the front panel of the DVR, log in 
when prompted and select OK to shut down. 
Not e  Only authorized users can shut down the DVR.  
 
Setting the Remote Controller ID 
When more than one HRDP  DVR is installed in the same location, you can 
use one remote controller to control multiple DVRs  –  up to 20 DVRs . To 
control mul tiple DVRs, you must change the remote controller ID to the DVR  
ID of the DVR.  
 
T o change the remote controller ID : 
1.   On  the DVR, go to SYSTEM > SYSTEM CONFIGURATION.  
2.   Enter the desired DVR ID number.  
3.   On the remote controller, press and hold the ID button and  enter the 
desired DVR ID number to operate the corresponding DVR. 
Note  The DVR ID must be input as two numbers on the remote controller. 
You must  input 00 for the system ID 0 and input 01 for 1.  
   
						

							HRDP DVR User Guide 
 
________________________________________________________________________\
______________________ 
Document 800 -06801   Rev D  29 
02/11    
Setup
 
 
Setup Menus  
 
 
Use the setup menus to configure all of the DVR settings, schedule recording, 
networking and shutdown.  
Press the SETUP key on the front of the DVR or remote control to enter the 
setup menus and log in. See the Logging In for the First Time section if 
entering setup for the first time. Use  the   and   keys on the front of the 
DVR or remote control to navigate individual menus, and use the   and   
keys to select a new setup menu.  
    
						

							Setup 
 
________________________________________________________________________\
______________________ 
30  
   
Setup Wizard  
The Setup Wizard allows you to define global recording settings for an easy 
and custom recording schedule on the DVR.  
 
 
 
Global Resolution  –  352 x240 / 704 ×  240 / 704 ×  480.  
Record Mode  –  Continuous / Motion   
Average Days to Record  –  [The estimated days of recording determined by 
resolution, IPS (Images Per Second), Picture Quality, and available storage 
size.]  
IPS Per Channel  –  1-30 [Maximum varies with resolution.]  
Picture Quality  –  Low / Normal / High / Highest