Honeywell Fusion 3 User Manual

GETTING STARTED 
3–5 
 
3.7 LOOPING OUTPUTS 
  The back of the DVR unit contains up to 32 video outputs, which may be connected to 
video monitors or VCR’s, depending on the DVR model. The connectors are standard 
BNC connectors and may require termination depending on the destination of the 
output. Make sure there is a video source connected to the corresponding input and 
then connect a cable to the Channel Out. 
  
8 Channel DVR 
 
 
16 Channel DVR 
 
 
32 Channel DVR 
 
 
  

FUSION III DVR Digital Recording and Transmission System 
3–6 
 
3.8 LOOPING OUTPUT TERMINATION 
  When terminating the outputs becomes necessary, the DVR unit has built-in 
termination that allows you to select individual outputs to be terminated. Generally it is 
not necessary to terminate the output when using it. It is dependant on if the device to 
which you are connecting it, has internal 75 ohm termination. As a rule, if the image 
appears distorted or virtually un-viewable, it most likely needs...

GETTING STARTED 
3–7 
 
3.10  CONNECTING CONTROL OUTPUTS TO THE DVR 
  Each DVR unit may have up to 16 Control Outputs. These outputs can be used to 
trigger devices such as Sirens, Phone Dialers, Lights, and any other relay activated 
device. 
  
Control 
Output 
 
  
 
•  Use 12V, below 300mA. For controlling lights or other high current devices, use an 
external relay. 
•  Maximum voltage is 24V AC @ 1 amp 
•  Output uses a Form C Relay  (NC-C-NC) 
  
  

FUSION III DVR Digital Recording and Transmission System 
3–8 
 
3.11  CONNECTING A 16 CHANNEL AUDIO OCTOPUS CABLE 
  The 16 channel audio octopus cable (Standard with the 16Ch 480PPS Fusion DVR) 
connects to a single serial port in the back of the unit.  
  
Rear 
Connection 
 
 
•  When connecting the 16 Channel Octopus Cable, make sure to properly secure 
the cable to insure no loss of audio 
•  Default audio in the 16 Channel 480 PPS Fusion 3 Model 
(included) 
 
3.12 OPTIONAL COMPONENTS 
  To fully...

 
4–1 
SECTION 4 
DVR BASICS 
4.1  TURNING ON THE DVR 
  Once the cables have been properly connected, it is time to turn on the power.  
 
1.  Turn on the monitor and any external peripherals (ex. Printers, External Storage 
Devices, etc.) connected to the DVR unit.  
 
2.  Turn on the main power switch located on the front of the DVR unit as shown 
below.  
  
  The DVR will run a series of self-tests. After two or three minutes, a series of 
messages may be displayed as the various hardware and...

FUSION III DVR Digital Recording and Transmission System 
4–2 
  2.  Click Camera Setup 
  3.  Click the Registration button 
  4.  In the Network Device Authentication, the System ID can be located under the 
“Add a new Serial Key” section (shown below) 
 
 
 
4.3.1  OBTAINING THE UNLOCK CODE 
  1.  Open an Internet browsing software and go to: http://registration.fusiondvrsupport.com/honeywell/Registration/SWregistration.aspx 
  2.  Enter the Product Serial Number that was provided by Honeywell 
  3....

DVR BASICS 
4–3 
 
 
  7.  Once validated, you will be provided with the Unlock Code 
  8.  Print the page and save for later reference 
 
 
  

FUSION III DVR Digital Recording and Transmission System 
4–4 
 
4.3.2 UNLOCKING YOUR NEW NETWORK DEVICE 
  1.  Start your Fusion DVR 
 2. Enter Setup 
  3.  Enter Camera Setup 
  4.  Click the Registration button 
  5.  Enter the Unlock Code generated by the Honeywell Registration Site into the 
“new serial number” field 
  6.  Click Add a serial number 
  7.  Once the new serial number has been added to the list, click OK 
 
  

DVR BASICS 
4–5 
 
4.4 DISPLAY SCREEN 
  Each time the DVR is restarted, the program defaults to the Display screen.  
The following diagram outlines the buttons and features used on the Display screen. 
Become familiar with these options as this is the screen that will be displayed the 
majority of the time. 
       
  
 
1 Camera Display 
Buttons Controls camera display options including number of 
cameras displayed on screen, full screen mode, and 
looping camera displays. 
 
2 Date/Time Displays...

FUSION III DVR Digital Recording and Transmission System 
4–6 
 
4.5 CAMERA VIEW 
  The Cameral status for each camera is displayed next to the Camera number (or 
name) on the Video Display Area.  
  
12 3
 
 
 
1 Camera Number 
and Name Displays the camera number and the custom name given 
to the camera. 
 
2 Recording Status Displays the current recording status of the camera using 
symbols.  
 
3 Special Recording Displays text relating to the type of recording that is 
occurring.