Honeywell Fusion 3 User Manual

PAN / TILT / ZOOM 
7–3 
 
7.2.1 SUPPORTED PROTOCOLS 
  Protocols are added frequently. The supported list may contain new protocols that are 
not listed here. 
  The current supported protocols are: 
 
Ademco Rapid Dome  KDC 
 
American Dynamics  LG (LVC-A70xs) 
 
CBC (GANZ)  LG SD-110 
 
C-BEL LG (LPT-A100L) 
 
Chiper CPT (V9KR Series)  Merit LI-LIN 
 
CNB-AN102 NiceCam 
 
CNB-PTZ100 Panasonic 
 
Computar Pelco D 
 
Dong Yang Unitech (DRX-502A)  Pelco (P protocol 4800bps) 
 
Dennard Philips (TC8560 &...

FUSION III DVR Digital Recording and Transmission System 
7–4 
 
7.3  SETTING UP A PTZ CAMERA (60IPS /120IPS) 
  
RS-485 ADAPTER 
RED Positive (TX+) 
  Setting up a PTZ Camera is simple since 
the DVR unit comes preassembled with 
an internal RS-485 adapter. 
BROWN Negative (TX-) 
  1.  Locate the PTZ adapter.  
(Refer to Section 3.1 for assistance 
identifying the adapter.) 
2.  Connect the two wires of the PTZ 
adapter to the PTZ camera. The red 
wire on the adapter should connect to 
the RX+ on the...

PAN / TILT / ZOOM 
7–5 
 
7.4  ADVANCED PTZ SETUP 
h 
 
1 Camera Menu Opens the OSD PTZ camera menu.  
 
2 On-Screen Compass Allows On-Screen control of a PTZ camera.  
 
3  RS-232 / RS-485 Defines how to send the PTZ signal to the camera. 
 
4 Select Camera Selects the current camera to be edited. 
 
5 Port Settings Defines the specific settings to transmit to the PTZ.  
 
6  Enable Pan/Tilt and 
Reverse PTZ Pan/Tilt Enables the DVR to control the PTZ camera. 
Reverse PTZ enables the PTZ to have inverse...

FUSION III DVR Digital Recording and Transmission System 
7–6 
The protocol is the unique set of instructions that 
allows the DVR to communicate with the PTZ 
camera. 
 
9  PTZ Status on Close This option will activate a Tour or Preset when the 
PTZ controller is closed.  
 
10 Address Setting Only available on select PTZ cameras. These options 
need to be set when there are more PTZ cameras 
connected together than there are inputs on the 
DVR. Setting these options allows for attaching 
several DVRs...

PAN / TILT / ZOOM 
7–7 
 
7.5  CREATING AND VIEWING PRESET POSITIONS 
  A Preset Position is a user-defined location where the camera can be pointed, zoomed in, 
and focused. Preset positions can be defined and labeled if the camera supports this. 
Each preset can have an independent Dwell and Speed setting for use with the Tour 2 
Function. 
 
  
          4 
       
 5 
                           2 
              3 
            
           1 
          2 
         3...

FUSION III DVR Digital Recording and Transmission System 
7–8 
 
7.5.1  CREATING A PRESET 
 1. Inside Setup, select the PTZ setup option and the camera 
to edit. 
2.  Inside the Preset options select a Preset you would like to 
modify (a red box will appear around the Preset). 
3.  Use the Pan/Tilt/Zoom/Focus controls to move the 
selected camera to the desired position.   
4.  Enter a Dwell Time and Speed setting. This is used for the 
Tour 2 function (Each Preset can have a different Dwell 
and Speed...

PAN / TILT / ZOOM 
7–9 
 
7.6 UNDERSTANDING TOURS 
  The following section explains the PTZ Tour options. Not every Tour Method will be 
available for each PTZ camera. 
 
 
1 Tour Method Defines the type of Tour to use. 
 
 Preset Tour Cycles through the selected Recorded Presets.  
 
 Preset Tour 2 Cycles through the selected Recorded Presets with the 
addition of a definable Travel Speed and Dwell Time.  
 
 Mimic Tour This Tour ‘mimics’ a user-defined motion path, copying 
everything the user does...

FUSION III DVR Digital Recording and Transmission System 
7–10 
 
8 Tour Schedule The Tour Schedule option allows for the setting of a Tour 
Schedule. 
  
7.6.1  CREATING A PRESET TOUR 
  1.  Start by creating two or more Preset Positions. (refer to Section 7.4.1) 
 2. Select the Preset Tour Method. The Preset Tour is now the default Tour method.  
  3.  The Tour is now set to cycle through the defined presets. 
 
7.6.2 VIEWING THE PRESET TOUR 
  1.  From the Main Display Screen, select the PTZ option....

PAN / TILT / ZOOM 
7–11 
 
7.6.5  CREATING A MIMIC TOUR 
 1. Select the Mimic Tour Method. 
 2. Press the Start Position button. 
  3.  Using the PTZ Controller, move the PTZ in the path of the tour to mimic. 
 4. Press the Stop Position button when finished moving the PTZ around. 
 5. Press OK or APPLY to save. 
 
7.6.6  VIEWING THE MIMIC TOUR 
  1.  From the Main Display Screen, select the PTZ option. 
  2.  Select the PTZ camera of the Tour you just created.  
  3.  Press the Tour Button. The MIMIC...

FUSION III DVR Digital Recording and Transmission System 
7–12 
 
7.6.7  PTZ TOUR SCHEDULING 
  The Fusion DVR provides an option with the PTZ setup called PTZ Tour Scheduling 
which allows users to specify set tour schedules for PTZ cameras connected to the 
DVR unit. The Tour Schedule allows for scheduling of specific days of the week and 
specific hours of the day for multiple PTZ cameras. Selected time frames are 
designated in blue and non selected (default frames) and shown in white. 
 
1  Day of...