Honeywell 1300g2 Manual

3 - 7
Scan the Hands Free Time-Out bar code, then scan the time-out duration 
(from 0-300,000 milliseconds) from the inside back cover, and Save.   Default = 
5,000 ms.
Reread Delay
This sets the time period before the scanner can read the same bar code a sec-
ond time.  Setting a reread delay protects against accidental rereads of the 
same bar code.  Longer delays are effective in minimizing accidental rereads at 
POS (point of sale).  Use shorter delays in applications where repetitive bar 
code...

3 - 8
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the bar code below, 
then set the delay (from 0-30,000 milliseconds) by scanning digits from the 
inside back cover, then scanning Save. 
Centering
Use Centering to narrow the scanner’s field of view to make sure the scanner 
reads only those bar codes intended by the user.  For instance, if multiple codes 
are placed closely together, centering will insure that only the desired codes are 
read.
If a bar code...

3 - 9
Left of Centering Window
Right of Centering Window
* Centering Off Centering On 

3 - 10
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data 
(when scanning more than one symbol) in whatever order your application 
requires, regardless of the order in which the bar codes are scanned.  Reading 
the Default Sequence symbol programs the scanner to the Universal values, 
shown below.  These are the defaults.  Be certain you want to delete or clear all 
formats before you read the Default Sequence symbol.
Note: To make...

3 - 11
Output Sequence Editor   
Output Sequence Example
In this example, you are scanning Code 93, Code 128, and Code 39 barcodes, 
but you want the image scanner to output Code 39 1st, Code 128 2nd, and 
Code 93 3rd, as shown below.
Note: Code 93 must be enabled to use this example.
You would set up the sequence editor with the following command line:
SEQBLK62999941FF6A999942FF69999943FF
The breakdown of the command line is shown below:
SEQBLKsequence editor start command
62 code identifier for Code...

3 - 12
42 start character match for Code 128, 42h = “B”
FF termination string for second code
69 code identifier for Code 93
9999 code length that must match for Code 93, 9999 = all lengths
43 start character match for Code 93, 43h = “C”
FF termination string for third code
To program the previous example using specific lengths, you would have to 
count any programmed prefixes, suffixes, or formatted characters as part of the 
length.  If you use the example on page 3-11, but assume a  suffix and...

3 - 13
Output Sequence Editor   
Require Output Sequence
When an output sequence is Required, all output data must conform to an 
edited sequence or the image scanner will not transmit the output data to the 
host device.  When it’s On/Not Required, the image scanner will attempt to get 
the output data to conform to an edited sequence, but if it cannot, the image 
scanner transmits all output data to the host device as is.
When the output sequence is Off, the barcode data is output to the host as the...

3 - 14
beeping (if turned on) for each read.  The scanner attempts to find and decode 
new symbols as long as the trigger is pulled.  When this programming selection 
is turned Off, the scanner will only read the symbol closest to the aiming beam.
No Read
With No Read turned On, the scanner sends an “NR” to the host if you pull and 
release the trigger without reading a code (e.g., bad bar code).  If No Read is 
turned Off, the “NR” will not be sent to the host.
If you want a different notation than...

3 - 15
Video Reverse
Video Reverse is used to allow the scanner to read bar codes that are inverted.  
The “Off ” bar code below is an example of this type of bar code.
Note:  If additional menuing is required, Video Reverse must be disabled to read 
the menu bar codes and then re-enabled after menuing is completed.
On
VIDREV0REV.
* Off 

3 - 16