Honeywell 1300g2 Manual

2 - 25
RTS/CTS Off, RTS Inactive: RTS/CTS is turned off so no data flow control is 
used and RTS is inactive.
Flow Control, No Timeout:  The scanner asserts RTS when it has data to 
send, and will wait indefinitely for CTS to be asserted by the host.
Character-Based Flow Control, No Timeout:  The scanner asserts RTS when 
it has a character to send, and will wait indefinitely for CTS to be asserted by the 
host
Two-Direction Flow Control:  The scanner asserts RTS when it is OK for the 
host to transmit....

2 - 26
Character-Based Flow 
Control, No Timeout
Two-Direction Flow 
Control
    Flow Control with 
Timeout
    Character-Based Flow 
Control with Timeout    
    CTS-Based Flow Control, 
No Timeout
 RTS On
No RTS if CTS is On 

2 - 27
RS232 Timeout
When using Flow Control with Timeout, you must program the length of the 
delay you want to wait for CTS from the host.  Set the length (in milliseconds) for 
a timeout by scanning the bar code below, then setting the timeout (from 1-
65535 milliseconds) by scanning digits from the inside back cover, then scan-
ning Save.   Default = 1000.
XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start send-
ing data (XON/XOFF On) or to stop sending data (XON/XOFF...

2 - 28
for ACK/NAK again.  Turn on the ACK/NAK protocol by scanning the ACK/NAK 
On bar code below.  To turn off the protocol, scan ACK/NAK Off.  Default = 
ACK/NAK Off.
Scanner to Bioptic Communication
The following settings are used to set up communication between Honeywell 
scanners and bioptic scanners.  
Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout 
must be set to 3000 in order to communicate with a bioptic scanner.  See 
RS232 Modifiers on page 2-22, and RS232 Timeouton...

3 - 1
3
Input/Output Settings
Good Read Indicators
Beeper – Good Read
The beeper may be programmed On or Off in response to a good read.  Turning 
this option off, only turns off the beeper response to a good read indication.  All 
error and menu beeps are still audible.  Default = On.
Beeper Volume – Good Read
The beeper volume codes modify the volume of the beep the scanner emits on 
a good read.  Default = High.
* On
 Off
*HighMedium
Off  Low 

3 - 2
Beeper Pitch – Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner 
emits on a good read. Default = Medium
Beeper Duration – Good Read
The beeper duration codes modify the length of the beep the scanner emits on 
a good read.  Default = Normal.
Low (1600 Hz)
* Medium (2750 Hz)
High (4200 Hz)
* Normal Beep
Short Beep 

3 - 3
Beeper Pitch – Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner 
emits when there is a bad read or error.  Default = 100 Hz.
LED – Good Read
The LED indicator can be programmed On or Off in response to a good read.  
Default = On.
Number of Beeps – Good Read
The number of beeps of a good read can be programmed from 1 - 9.  The same 
number of beeps will be applied to the beeper and LED in response to a good 
read.  For example, if you program this option to have...

3 - 4
LED flashes are in sync with one another.  To change the number of beeps, 
scan the bar code below and then scan a digit (1-9) bar code and the Save bar 
code on the  inside the back cover of this manual.  Default = One.
Good Read Delay
This sets the minimum amount of time before the scanner can read another bar 
code.  Default = No Delay.
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the bar code 
below, then set the delay (from 0-30,000...

3 - 5
Trigger Modes
Manual/Serial Trigger
You can activate the scanner either by pressing the trigger, or using a serial trig-
ger command (see Trigger Commandson page 9-4).  When in manual trigger 
mode, the scanner scans until a bar code is read, or until the trigger is released.  
When in serial mode, the scanner scans until a bar code has been read or until 
the deactivate command is sent.  In serial mode, the scanner can also be set to 
turn itself off after a specified time has elapsed (see Read...

3 - 6
Presentation Mode
Presentation Mode uses ambient light to detect bar codes.  The LEDs are off for 
ambient conditions until a change occurs in the scanner’s field of view.  Then 
the LEDS turn on automatically to read the code.  If the light level in the room is 
not high enough, Presentation Mode may not work properly.
Continuous Illumination Mode (Manual Trigger only)
If you have several bar codes that are close together, you may wish to have a 
continuous aiming beam on in order to properly aim...