Hitachi Z3000w Manual

48
ç
çç çSetup card
çç




ç





çç




ç

ç



ççççç




ççççççøççç
þõ÷øõ÷øçøù

÷÷
ççççççùççç
þõ÷ýõ÷øçøù

÷÷
ççççççúççç
þõ÷ùõùùçøù

÷÷
ççççççûççç
þõ÷úõ÷øçøù

÷÷




ç






çç
 

çççô




ç
ï




ð
çç







ô




çï

ð
5. 
If the cursor is positioned at the correct File
No., press the    button for Yes.  If the
number is incorrect, press the 
Ú
 button for
Cancel and return to the Memory Card Top
menu, then press the    button.  To end the
menu, press...

49
ç
çç çViewfinder indications
Lighted indicators
The following lighted indicators appear above and below the viewfinder screen.
！
ＢＴ
Ｓ
T
:TALLY (Tally) 
B
:BATT (Battery) 
S
:VTR SAVE (VTR save)
!
:
(Setting discrepancy) 
VTR connected:    Lights during recording
CCU connected:    Lights at tally signal
Lights to indicate low battery voltage.
Immediately replace the battery when
lighted.
Lights when Power switch is set to VTR
Save.
lights in the following situations
Gain switch other than Low
Shutter...

50
ç
çç çViewfinder indications
In addition to the video image, the viewfinder displays messages related to camera settings and operating status,
center and safety zone markers and other information.
Ô
When set to on at the setting menu VF Display page, setting items are indicated at the top and bottom edges of
the screen.
Ô
Messages regarding switch changes and adjustments are shown for about 3 seconds at the center of the
screen.
CAM mode
The above items are indicated only when set to on at the...

51
ç
çç çViewfinder indications
Display description
Item Description
Extender (No indication)
E
W
Extender off
Extender on
Wide setting (
×0.8) on
Shutter speed OFF
1/100,1/250,1/500,1/1000,1/2000
1/61.58 to 1/2097
CC FRM
AESShutter off
Preset shutter
Lock scan mode
CC frame mode
Auto electronic shutter mode
REC Time 000 MIN to 255 MIN Cumulative recording time.
To reset, simultaneously press the              buttons
during REC Time display.
Battery voltage 12.0 to 13.2 V Indicates...

52
ç
çç çViewfinder indications
Check mode
Set the switch to Check and press the Check button.    The CAM mode is returned about 3 seconds after
releasing the button.
Ô
All items of the CAM mode are indicated at the top and bottom edges of the screen (see CAM mode
description).
Ô
The center of the screen shows the DTL, Flesh tone and other switch setting states.
Display description
Item Description
DTL levelDTLOFF, -128...........0........+127
Flesh toneFLESH TONEON, OFF
MaskingMASKINGOFF,...

53
ç
çç çViewfinder indications
One line indicating mode
The switch operation effect is indicated at the 2nd line from the bottom.
Display description
Switch Description
Effect (set to Zebra)ZEBRA

ON, OFF
ULTRA GAINULTRA GAIN

ON, OFF
FLESH TONEFLESH TONE

ON, OFF
DNRDNR

ON, OFF
CS-1, CS-2CONTRAST

OFF, NORMAL, HIGH
QUICK FOCUS

ON, OFF
FULL AUTO

ON, OFF
OUTPUT(AUTO KNEE)AUTO KNEE

ON, OFF
CC/ND FILTERFILTER

3200K, 5600K+1/16ND, 5600K,
EFFECT
ÚÜIRIS

+1.0, +0.8, +0.4, +0.2, 0,...

54
ç
çç çStatus Indication of Viewfinder Screen
BARS mode
(Note) Above items are set at the Function (BAR mode) menu.
Ÿ}}


)y/

55
ç
çç çFunction menu screen
Settings with Function menu
Preparation menu
Settings can be changed by using the Function menu.    The principal settings are as follows.
  
     Mode    Menu Description
1)  CAM    Setup Card Settings when using setup card
2)  CAM    Function 1 Memory items for each scene file
3)  CAM    Function 2 Other memory items
4)  CAM    VF Display Viewfinder display selection
5)  BAR    Bar Function Main menu for Bar mode
6)  BAR    GL Set Genlock adjustment
7)  BAR    ID Set...

56
  Function menu screen
CAM mode (Output switch)
Standard menu
ç




ç





çç




ç

ç



ççççç




ççççççøççç
þõ÷øõ÷øçøù

÷÷
ççççççùççç
þõ÷ýõ÷øçøù

÷÷
ççççççúççç
þõ÷ùõùùçøù

÷÷
ççççççûççç
þõ÷úõ÷øçøù

÷÷
çç



ç




ô




ç
ï




ð




ç




ô




ç
ï




ð







ô




ç






ò
ç









çøçç





çø

57
  Function menu screen
CAM mode (Output switch)
Full menu
çç






ç






 

çççç