Hitachi Z3000w Manual

8
ç
çç çFacility names and functions
17Power switch
¤
VTR STDBY/SAVEz
CAM ON/OFF¥
Left:  (VTR:STDBYz
CAM:ON)
Both camera and VTR power on and
recording starts.
Center:  (VTR:SAVEz
CAM:ON)
Camera power on, VTR power save
mode
Right:  (VTR:SAVEz
CAM:OFF)
Camera power off, VTR power save
mode.
18
Power LED
Off :    Camera power not supplied.
Lights (green):  Camera power supplied, but
power switch is off.
Lights (red) : Camera power switch on.
19
Check  switch
At the Check setting, the viewfinder...

9
  Facility names and functions
24Scene file LEDs
Light to indicate the scene file selected by the
Scene File buttons  25
.
25
Scene File buttons
Select from among 4 scene files.
26
Function button
Used for changing settings (e.g., detail amount).
27
Up/down buttons
Change the setting selected by the Function
button 26
.
28
Left/right buttons
Change the setting selected by the Function
button 26
.    In the lock scan mode, use for
adjusting the shutter speed.29
Ultra gain on/off switch
ON
Increase...

10
ç
çç çFacility names and functions
32Video output connector (BNC)
Composite video signal output (1 Vp-p/75Ω
).
33
Monitor output connector (BNC)
Video signal output for monitor (1 Vp-p/75Ω
).
The same character signal as the viewfinder is
superimposed on the video signal to allow
checking the setting menu from the monitor
screen.
34
Genlock In connector (BNC)
Reference signal input for applying genlock to the
camera.
35
Remote control connector (4 pin)
Connection for RC-Z1, RC-Z11, RC-Z2A or RC-
Z21A...

11
ç
çç çFacility names and functions
43Rear cover
Contains connections for battery and extension
adapter, etc.
44
DC IN connector (XLR, 4P)
Connect the separately sold AC adapter for
operating from AC power.
45
Intercom connector (XLR, 5P)
Connect intercom headset (MT-12MF) when
using the RU-Z1/RU-Z2 / RU-Z3.46
150 V Out connector (5 pin, CA-Z32 only)
Connect 150 V to 12 V power supply adapter
when using a large size lens.
47
Audio monitor connector (minijack)
Connect an earphone (8 to 10Ω
) to monitor...

12
ç
çç çFacility names and functions
48Brightness control
Adjusts viewfinder screen brightness.    Does not
affect camera output signal.
49
Contrast control
Adjusts viewfinder screen contrast.    Does not
affect camera output signal.
50
Peaking control
Adjusts viewfinder video contours for easier focus
adjustment.    Does not affect camera output
signal.
51
External tally switch
ON
External tally lamp lights.
OFF
External tally lamp does not light.
52
Camera connector
Connects viewfinder to...

13
 Lens installation
1
Raise the lens lever and remove the mount cap.
2
Align the lens center mark with the indent at the
upper part of the lens mount and install the lens
3
Lower the lens lever to secure the lens.
4
Engage the cable with the cable clamp and connect
it to the lens connector.
ÔRefer to the lens instructions when using the lens.
Notes:
The following adjustments may be required according
to the type of lens.
1
}Lens flangeback
2
}Lens auto iris speed
3
}
Lens white shading (with camera) 

14
  Lens flangeback adjustment
When operating a zoom lens, if the focus is not precisely aligned at both the telephoto and wide angle
extremes of the lens, the flangeback (distance from the lens mounting plane to the focal plane) is adjusted.
This adjustment is generally required only once unless the lens is replaced.
Reference
Refer to the lens operating instructions regarding the component positions for flangeback adjustment.
Flangeback adjustment
1Set the lens iris for manual operation.
2Open the...

15
  White shading adjustment
White shading adjustment is recommended after replacing the lens.    The adjustment relates to the
camera vertical coloration.    If the lens includes an extender, the shading can be optimized for both
extender on and off modes.
(Vertical coloration refers to an effect whereby the image of an overall white sheet of paper tends toward
green at the top and magenta at the bottom, or vice versa.)
Adjustment steps
1Install the lens on the camera (be sure to connect the lens...

16
  White shading adjustment
5
FUNC  
yy 

17
  Camera adapter installation
　　　
1. Align the adapter with the camera guide
and guide pin.    Attach the adapter and
engage the connector.
2.  Tighten the screws provided with the
handle to secure the camera adapter to
the camera.
　　
    CAUTION
Tighten the screws completely.    Check for
absence of wobble between the camera and
adapter.
3.
　　Install the handle with two screws.
　　
!