Hitachi Z3000w Manual

18
ç
çç çMicrophone installation
Mic holder attachment
Attach the MH-Z3 microphone holder (separately sold).
Microphone
Install the (separately sold) MC-Z2 microphone and C-300MA microphone cable as follows.
1.Attach the MC-Z2 microphone to the mic holder.
2.Connect the C-300MA mic cable to the microphone.
3.Secure the cable in the cable clamp and connect to the MIC IN connector.
Microphone power and sensitivity
Set from Function 2 menu screen.
1.
Phantom power (+48 V) can be supplied.    Set to on for...

19
 Tripod mounting
Use the accessory TA-Z3 tripod adapter to mount
the camera on a tripod.
1.Securely attach the tripod adapter to the tripod.
Shift the adapter screw position to obtain the
best balance.    The adapter can accept two
types of screws.    Use the screw hole that
matches the tripod.
2.Secure the camera on the tripod adapter.
Align the hooks of the camera and adapter,
then turn the lock lever in the direction
indicated by the arrow.    A click sound can be
heard at the locked position....

20
  Shoulder pad position
The shoulder pad can be shifted up to 15 mm in either direction from the center (factory) position.    The
position can be adjusted for comfortable operation.
1.Loosen 2 screws.
2.Slide the pad forward or rearward to the best position.
3.Tighten the 2 screws. 

21
  Anton-Bauer battery pack
Anton-Bauer battery pack
Procure the separately sold battery holder to operate the camera from an Anton-Bauer battery.
1.Use 4 screws to attach the battery holder to the rear of the camera adapter.
Note:The optional buttery holder connecting cable is required.    Consult Hitachi denshi service center.
2.
Attach the battery pack.    Insert and slide the battery pack.
3.Set the camera adapter Power Select switch to BATT.
4.To remove the battery, set the battery holder...

22
GM-51 5-inch viewfinder attachment
Use the separately sold AT-30 viewfinder adapter when installing the GM-51 5-inch viewfinder.
1. 
Raise the lock lever of the AT-30 horizontally and remove the viewfinder mounting screw from the AT-30.
Insert this screw in the bottom of the GM-51.    Insert the screw together with the GM-51 into the AT-30 and set
the lock lever forward, then turn the lever clockwise to secure it.
2. Insert the GM-51 and AT-30 into the slot at the rear of the handle and slide them...

23
GM-51 5-inch viewfinder attachment
3. 
Removal
Disconnect the viewfinder cable.
Turn the AT-30 lock lever B
counter-clockwise and pull the
release knob to allow removing
both the GM-51 and AT-30. 

24
 VTR connection
VTR docking
Examples of compatible VTRs
Sony DNV-5 (BETACAM SX)
BVV-5 (BETACAM SP£
PVV-3¢
BETACAM SP2000PRO£
DSR-1¢
DVCAM£
Matsushita (Panasonic)AUµ
45H¢
M˜
 Promind£
AJ-D90¢
DVCPRO£
JVCBR-S422¢
S-VHS£
BR-D40¢
DIGITAL-S£
Required inner modules (separately sold)Note:
Refer to the VTR and inner module instructions for
details regarding installation.
Note:
VTR examples are shown only for
general reference.  Model names
and specifications are subject to
change. 

25
 VTR connection
VTR types and connections
SystemMain VTR
VIDEO(VTR) AUDIOLEVEL CA-Z31 CA-Z32
VTR inner
module
BETACAM COMP100% -60dBµµµ µµµ
IM-Z3D DNV-5
BVV-5
µµµ µµµ
IM-Z3S PVV-3
C-201TE
C-501TEC-201TB
C-501TBµµµ
BVW -50
DVCAM COMP100% -60dBµµµ µµµ
IM-Z3S DSR-1
M2 COMP75% -60dBµµµ µµµ
IM-Z3P AU-45H
C-201TE
C-501TEC-201TB
C-501TBµµµ
AU-520
DVCPRO COMP75% -60dBµµµ µµµ
IM-Z3P AJ-D90
S-VHS Y/C -20dBµµµ µµµ
IM-Z3P BR-S422
C-201TD C-301TFµµµ
(AG-7400)
(BR-S400)...

26
 
VTR connection
VTR power save
When the camera PWR switch is set to VTR Save, the VTR types operate as follows.
VTROperation
DNV-5,BVV-5,
PVV-3, DSR-1,
AU-45H,AJ-D80The VTR goes to power save mode to
avoid battery depletion
BR-S422,
BR-D40All VTR operations inhibited.
REC review and playback monitor
When the VTR includes a recording review function, in the VTR REC Pause mode, press the lens RET
button to view the final few seconds of the recording in the viewfinder.    By setting the VTR to the...

27
 
Power supply
When the CA-Z31/CA-Z32 is installed, power can
be supplied as follows.    Set the Power Select
switch accordingly.
1. Connect the separately sold AP-60 AC adapter
to the DC IN connector.
2. Connect the camera base station or VTR to the
CCU/VTR connector.
3. Connect Anton-Bauer battery.
¢Note£
ÔWhen a Betacam type VTR is directly connected
to the camera, power is supplied from the VTR.
Caution
1. The DC IN connector can accept 10.5 to 17 VDC.
However, use a designated power supply of...