Hitachi Projector CP-WX8650 User Manual

31
  In a normal state  
The Status Monitor displays the state of the projector in 
three lines.
:  Displays the condition of the projector. 
While the lamp is on, the selected port is 
displayed.
Displayed conditions are as below;
STANDBY : The projector is in standby mode.
WARM UP: The projector is warming up.
SEARCHING: The projector is searching an input signal.
COOL DOWN:    The projector is cooling down.
:   Displays the condition of the detected input signal while the lamp 
is on. Otherwise,...

32
Displaying the condition of the projector (continued)
• While the projector is searching an input signal in normal condition, 
nothing is displayed on the 2nd line of the monitor.
• Displayed temperature might differ from actual peripheral temperature 
because the displayed temperature is measured inside of the projector .
NOTE
Status Monitor 
  
In error state 
The Status Monitor displays a warning of an error with 
larger letters. Resolve the errors referring to the table 
of the sections...

33
Status  Monitor  
When the projector is in a normal condition, 
or displays one of the warnings of AIR FLOW, 
COLD or FILTER errors, press the FUNCTION 
button on the control panel, press the ENTER 
button on the remote control for three seconds 
or press one of the MY BUTTON buttons if 
assigned as STATUS MONITOR. The backlight 
of the monitor turns on.
  To display the setup information including 
usage time
Use the ◄/►  buttons to switch display. 
     
  
Usage time: The Status Monitor displays...

34
AC240V35°C
7FILTERERRO
1PREVIOUS
  To display error history 
Press the ▲ button to display previous error 
log. If a warning has been displayed, the 
first previous error log is the present error 
currently occurring. The Status Monitor 
displays the log number, occurred error, the 
supplied voltage and peripheral temperature 
at that time. Press the  ► button to display the 
usage time when each error occurred. 
Use the ▲/▼ buttons to switch the log. 
The display switches with the ◄/► 
buttons at...

35
1.Make sure that the power cord is firmly 
and correctly connected to the projector 
and the outlet.
Turning on the power
2.Make sure that the POWER indicator is 
lighted in steady orange (
11 7). Then 
remove the lens cover.
3.Press STANDBY/ON button on the projector  
or the ON button on the remote control.
The projection lamp will light up and  POWER indicator will begin blinking in 
green. When the power is completely on, the indicator will stop blinking and 
light in steady green (
11 7 )....

36
►A strong light is emitted when the projector’s power is on.  
Do not look into the lens of the projector or look inside of the projector through 
any of the projector’s openings since the projection ray may cause a trouble on 
your eyes.
►Keep any object away from concentrated projection light beam. Blocking the 
beam by something causes high temperature and could result in fire or smoke.
►Do not touch around the lamp cover and the exhaust vents during use or just 
after use, since it is too hot....

37
Operating
Operating
1.
Adjusting the volume
Use the VOL + / - buttons to adjust the volume. 
A dialog will appear on the screen to aid you in 
adjusting the volume. If you do not do anything, 
the dialog will automatically disappear after a few 
seconds.• 
When  is selected for current picture input port, the volume 
adjustment is disabled. Please see AUDIO SOURCE item of AUDIO menu (
 80).
• Even if the projector is in the standby mode, the volume is adjustable when 
both of the following conditions...

38
Operating
1.Press INPUT button on the projector. 
Each time you press the button, the projector 
switches its input port from the current port as 
below.
Selecting an input signal
1.
INPUT button
   SHADE           LAN    COMPUTER IN     HDMI 1
         VIDEO                                      HDMI 2
           SDI*       HDBaseT      DisplayPort 
Buttons for input 
ports
• If you have set SKIP to some ports from SOURCE SKIP in the 
OPTION menu, the input from the ports cannot be selected (
...

39
Operating
Selecting an aspect ratio
1.Press ASPECT button on the remote control.   
Each time you press the button, the projector switches 
the mode for aspect ratio in turn. 
ASPECT 
button
• ASPECT button does not work when no proper signal is input.
• NORMAL mode keeps the original aspect ratio setting. NOTE
  
For a computer signal  
CP-X8800:   
  NORMAL  4:3  16:9  16:10 
         
 
CP-WU8600, CP-WX8650, CP-WU8700, CP-WX8750:  
  NORMAL  4:3  16:9  16:10  NATIVE 
        
  For a video...

40
Operating
Adjusting the projector’s elevator
Lengthening or shortening the length 
of the elevator feet shifts the projection 
position and the projection angle.
Turn the elevator feet each to adjust 
their length.
►Do not lengthen the elevator feet exceeding 30 mm. The foot
lengthened exceeding the limit may come off and drop the projector down, and
result in an injury or damaging the projector.
►Do not place the projector with an inclination exceeding
5 degrees. The projector leaned exceeding the...