Hitachi Projector CP-WX8650 User Manual

21
• To use a wired remote control, connect a wired remote control to 
the REMOTE CONTROL IN port. You can also connect another  projector to 
the REMOTE CONTROL OUT port to control it from the wired remote control. 
You can utilize this projector as a remote control-relay with the  REMOTE 
CONTROL IN and OUT ports. To connect the wired remote control or another 
projector to the REMOTE CONTROL IN  or OUT ports, use audio cables with 
3.5 mm diameter  stereo mini plugs. This function is useful when a...

22
CP-WU8700
SDI OUT
Connecting with your devices (continued)
Setting up
• The SDI port of this model supports the following SDI signals:
SD-SDI signal: conforming to SMPTE ST 259-C standard
YCBCR 4:2:2 10-bit
480i, 576i
Single link HD-SDI signal: conforming to SMPTE ST 292 standard YPBPR 4:2:2 10-bit
720p@50/60, 1080i@50/60, 1080sf@25/30
3G-SDI Level-A signal: conforming to SMPTE ST 424 standard YPBPR 4:2:2 10-bit
1080p@50/60
-  This projector can be connected with another equipment that has SDI...

23
It is recommended to fasten the HDMI cables by using the HDMI cable holder and 
the Cable tie to prevent them from coming off. Use a Cable tie with the size of 2.0 
x 4.0mm or smaller. 
Fastening the cables
►Do not fasten the cables other than HDMI.
►To fasten the cable, use a supplied Cable tie or plastic tie 
with the size of 2.0 x 4.0mm or smaller.  A metallic tie may cause damage to the 
cables and tie holder.
►Do not bind the cables too tightly. The cables or the hole might be damaged. WARNING...

24
When using the USB wireless adapter, use the supplied adapter cover for theft 
prevention.
USB wireless adapter: 
 USB-WL-11N 
Temperature range: 0 ~ 45°C(operating)
1. 
Loosen the screw on the bottom left of the  WIRELESS port.
2. 
Insert the tab of the cover into the hole at the upper right of the  WIRELESS 
port in the direction of the arrow.
3. 
Align the screw holes on the projector and the cover. Then insert the screw 
removed from the projector into the hole and tighten the screw.
Fastening the...

25
Setting up
Attaching the terminal cover
Insert the two claws of the Terminal cover into the hole of 
the case and confirm two Hooks are fitting into the case.
Terminal cover
When detaching the Terminal cover, push the Hook 
in the direction of the arrow and pull it forward. 
Hook
NOTE  • Do not attach the Adapter cover when attaching the Terminal cover. 

26
Using the security bar and slot
A commercially available anti-theft chain or 
wire can be attached to the security bar on 
the projector. Refer to the fi gure to choose 
an anti-theft chain or wire.
Also this product has the security slot for 
the Kensington lock. 
For details, see the manual of the security 
tool.
►Do not use the security bars and slot to prevent the projector 
from falling down, since it is not designed for it.
►Do not place anti-theft chain or wire near the exhaust vents. 
It may...

27
Setting up
►Do not connect the projector to a power supply while no lens 
unit is attached to it.
►Please use extra caution when connecting the power cord, as incorrect or 
faulty connections may result in fire and/or electrical shock.
• Do not touch the power cord with a wet hand.
•   Only use the power cord that came with the projector. If it is damaged, consult 
your dealer to get a new one. Never modify the power cord.
•   Only plug the power cord into an outlet whose voltage is matched to the...

28
Remote control
Installing the batteries
Please insert the batteries into the remote control before using it. If the remote 
control starts to malfunction, try to replace the batteries. If you will not use the 
remote control for long period, remove the batteries from the remote control and 
store them in a safe place.
1.Holding the hook part of the battery 
cover, remove it.
2.Align and insert the two AA batteries 
according to their plus and minus terminals 
as indicated in the remote control.  (Use...

29
Remote control
Changing the frequency of  remote control signal
The accessory remote control has the two choices on signal frequency Mode 
1:NORMAL and Mode 2:HIGH. If the remote control does not function properly, 
attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of two buttons 
listed below simultaneously for about 3 seconds.
(1)  Set to Mode 1:NORMAL  
MENU and MY BUTTON-4 buttons 
(2)   Set to Mode 2:HIGH 
AV MUTE and MY BUTTON-1 buttons
Please...

30
30°30°
3m
30°30°30°30°30°30°30°30°30°30°30°3m
(approx.)
About the remote control signal
The remote control works with 
the projector’s remote sensor. 
This projector has two remote 
sensors on the front and back 
sides.
The sensors can sense signals 
within the following range:
60 degrees (30 degrees to the 
left and right of the sensor) 
within about 3 meters.
• You can deactivate one of the sensors using the REMOTE RECEIV. 
item in the SERVICE menu of the OPTION menu (
95).
• The remote control...