Hitachi Projector CP-WU9100 User Manual

41
Blend Region
L eft I mageRight I mage
Using the EDGE BLENDING feature
Operating
Guide line
1. Mode (Manual/Camera)
OFF: Disables the Blending function.
 
Manual: Allows you to adjust Blending Region or Blending Level by using menu.
Camera:   
Allows you to perform automatic adjustment by using Camera in Projector 
Blending Tool.
• ECO MODE is not selectable when Blending is set to other than OFF .
•  Keystone/PERFECT FIT/Warping are not selectable when Camera is selected in 
Blending.
•  Camera...

42
Operating
3.  Cropping 
When inputting the same image to each projector, the Cropping function enables 
projectors to cut out a part of input image and display one image on a large 
screen. The following patterns are supported.
 
3.1 Displaying Cropping Menu 
Select CROPPING with ▲/▼ buttons and press 
►, ENTER or INPUT button to display Cropping 
Menu. 
 
3.2 Setting Cropping 
Select MODE with ▲/▼ buttons and select ON 
with ◄/► buttons. 
The input image is automatically cut out according to the...

43
Operating
 
3.3 Adjusting Cropping Area 
Adjust the Cropping Area when cutting out a part of input image.
Select SETUP with ▲/▼ buttons and press ►, ENTER or INPUT button.
*  MODE is set to [OFF] temporarily and the guide of the Cropping Area 
 is displayed.
Select [LT]/[WH] with ▲/▼ buttons and press the ENTER or INPUT button.
Move the guide display with ▲/▼/◄/► buttons to select the region of the 
screen to be cut out.
Press the ENTER or INPUT button and then press ◄ button to select SETUP, 
and...

44
4.  Selecting Blending Level 
Select the BLENDING LEVEL with ▲/▼ buttons. 
[1-25] can be selected with ◄/► buttons. 
Adjust the brightness of the Blending Region according to the settings.
5.  DIMMING LEVEL 
Adjusts the brightness of the projectors which are using Blending. 
Using the ◄/► buttons to adjust the DIMMING LEVEL.
6.  WHITE BALANCE 
Adjusts the white balance of the whole screen.
6.1.   OFFSET 
Changes the color intensity on the whole tones.
6.2.  GAIN 
Mainly affects color intensity on the...

45
1.
Using the magnify feature
2.
3.
4.
Press the MAGNIFY ON button on the remote 
control.  
The picture will be magnified, and the MAGNIFY 
dialog will appear on the screen. When the 
MAGNIFY ON button is pressed for the first time 
after the projector is turned on, the picture will be 
zoomed by 1.5 times. On the dialog, triangle marks 
to show each direction will be displayed.
While the triangles are displayed on the dialog, use the ▲/▼/◄/► cursor
buttons to shift the magnifying area.
Press the...

46
1.Press the SHUTTER button on the control 
panel. or on the remote control.
The mechanical lens shutter closes and 
the screen turns to black. The SHUTTER 
indicator on the projector blinks in yellow 
while the shutter is closed.  
To open the shutter and restore the screen, 
press the SHUTTER button again.
Temporarily shading the screen
1.Press the FREEZE button on the remote control.  
The “FREEZE” indication will appear on the screen 
(however, the indication will not appear when the 
SILENT is...

47
The PbyP / PinP is a function for displaying two different picture signals on a 
screen that is separated into main and sub areas for each signal. 
PbyP (Picture by Picture) / PinP (Picture in Picture)
PbyP buttonNormal modePbyP mode
main areasub area
PinP mode only
Press the PbyP button on the remote control. This activates the PbyP mode. 
Then, press the PbyP button again. The projector goes into PinP mode. The 
screen displayed before the PbyP button was pressed will be displayed as the 
main area....

48
The position of the main area can be toggled with the ◄/► buttons when the 
setting information is displayed on the screen. The frame will move together with 
it.
  Changing the main area
main areasub areamain areasub area
The setting information appears for several seconds when the PbyP / PinP
 function is started. Displays the input information for each area. A frame around 
the main area will be displayed. The information can be redisplayed with the 
◄/► buttons after it has been erased.
...

49
Press any button to select an input port on the remote control or press the 
INPUT button on the control panel. A dialog box to select the input signal for 
the main area will be displayed. Choose a signal using the ▲/▼ buttons. To 
change the signal in the sub area, switch temporarily across to the main area 
with the ◄/► buttons. 
Displaying the same signal on the both areas is not allowed. Refer to the table 
for details on available input signal combinations. Any combinations marked 
with...

50
Using ▲/▼ buttons on the remote control changes the size of main area in 
PbyP mode.
  Changing the size of main area in PbyP mode
  Changing the position of sub area in PinP mode
• For some signals, it may not be displayed correctly in the PbyP /
PinP mode, even if it can be displayed properly in the normal mode.
NOTE
Press the MY BUTTON assigned the PbyP / PinP SWAP (84). The position of 
the area is exchanged without any setting change.
  PbyP / PinP SWAP function
main areasub areamain areasub...