Hitachi Projector CP-WU9100 User Manual

31
Operating
Selecting an input signal
1. Activate your signal source. Turn the signal source on, to send signal to the 
projector.
2. Press the INPUT button on the projector.  
When you press the button, the projector switches its input port in turn. 
You can also use the remote control to select an input signal.  
Select from the buttons for input ports as the following. 
• If you have set SKIP to some ports from SOURCE SKIP in the 
OPTION menu, the input from the ports cannot be selected (82).
•...

32
Selecting an aspect ratio
  For a video signal 
 
 4:3  16:9  16:10  14:9  ZOOM  NATIVE 
  
  
For an input signal from the LAN, or if there is no signal  
CP-WU9100: 16:10 (fixed) 
CP-HD9950: 16:9 (fixed)
1.Press the ASPECT button on the remote control.   
Each time you press the button, the projector switches 
the mode for aspect ratio in sequence. 
  For an HDMITM, DVI-D and HDBaseT™ signal 
  
  NORMAL  4:3  16:9  16:10  14:9  ZOOM  NATIVE 
       
• The ASPECT button does not work...

33
►Do not place the projector with an inclination exceeding
5 degrees. The projector leaned exceeding the limit could cause malfunction and 
shorten the life of the projector.
CAUTION
Increasing or shortening the 
length of the elevator feet shifts 
the projection position and the 
projection angle.
Turn the elevator feet each to 
adjust their length.
5°
max. 30 mm
►Do not lengthen the elevator feet exceeding 30 mm. The foot 
lengthened exceeding the limit may come off and drop the projector down, and...

34
The ZOOM or FOCUS dialog will appear when 
you press any of the buttons from ZOOM, ZOOM -, 
ZOOM +, FOCUS + and FOCUS -. 
1. Use the ZOOM + / - buttons  to adjust 
the screen size.
2. Use the FOCUS + / - buttons to focus 
the picture.
Adjusting the lens 
Adjusting the zoom and focus
• The projector may ignore the operation 
by other buttons while the lens is moving.
NOTE
Press the LENS SHIFT button. The LENS SHIFT 
dialog will appear. Using the ▲/▼/◄/►buttons while 
the dialog is displayed shifts the...

35
This projector is equipped with memory functions for the 
lens adjustments (ZOOM, FOCUS, LENS SHIFT and 
LENS TYPE). Up to three sets of adjustments can be 
stored.
To use the lens memory feature, press the LOAD or 
FUNCTION button while the LENS SHIFT dialog is dis-
played, or press ▲ button while the ZOOM or FOCUS 
dialog is displayed. Then the LENS MEMORY dialog will 
appear. The current lens adjustments are displayed on 
the “CURRENT” line. The adjustments already stored 
in the lens memory are...

36
1.Press AUTO button on the remote control.  
Pressing this button performs the following.
Using the automatic adjustment feature
  For a computer signal 
The vertical position, the horizontal position and the  
horizontal phase will be automatically adjusted.  
Make sure that the application window is set to its  
maximum size prior to attempting to use this feature. A dark picture may still be 
incorrectly adjusted. Use a bright picture when adjusting.
   For a component video signal  
The vertical...

37
Operating
Other buttons 
HDCR:   Displays the HDCR menu (59).
C.WHEEL:   Displays the COLOR WHEEL menu (60).
OSD:   Displays the OSD MESSAGE menu (75),  
and it switches the function by pressing  
the button again. 
NORMAL  SILENT  INHIBIT 
   
All message functions do not work by selecting INHIBIT. •  To change this function, follow the steps below. 1. Press the OSD button on the remote control for 3 sec. 2. The INHIBIT OSD will be displayed.     While this OSD is displayed, press the OSD button...

38
   KEYSTONE: 
When KEYSTONE is pointed at, pressing the ► or 
ENTER button displays the KEYSTONE dialog.
1. 
Select the vertical or horizontal keystone ( / 
) with the ▲/▼ buttons.
2. 
Use the ◄/► buttons to adjust the keystone distortion.
• When the zoom adjustment is set to the TELE (telephoto focus),
this function may be excessive. This function should be used when the zoom
adjustment is set to the full WIDE (wide-angle focus) .
• When the horizontal lens shift is not set to the center, this...

39
Operating
   PERFECT FIT: 
When PERFECT FIT is pointed at, pressing the 
► or ENTER button displays the PERFECT FIT 
dialog.
This projector is equipped with a test pattern for 
PERFECT FIT. Select  PATTERN with the ▲/▼ 
buttons, then press the ◄/► buttons to switch on 
and off.
1. 
Select SETUP with the ▲/▼ buttons and  
 
press the ► or ENTER button.
2. 
Select one of the corners or sides to be adjusted 
 
with the ▲/▼/◄/► buttons and press the 
ENTER or INPUT button.
3. Adjust the selected part as...

40
Operating
4. This projector is equipped with a memory feature for PERFECT FIT 
adjustment. Up to three sets of adjustments can be stored.
●  SAVE:  
To store the current PERFECT FIT adjustment, select one of the "SAVE" 
options numbered 1 to 3 (number of the memory) with the ▲/▼ buttons and 
press the ►, ENTER or INPUT button.  
The current data being stored is lost by saving new data.
●  LOAD:  
To recall stored adjustments, select one of the "LOAD" options numbered 
1 to 3 (number of...